TP Link Switch TL SG1008D User Manual

User Guide  
TL-SG1005D  
TL-SG1008D  
5/8-Port Gigabit Desktop Switch  
Rev:2.0.2  
7106503707  
 
FCC STATEMENT  
This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to part 15 of the  
FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in  
a
residential  
installation. This equipment generates, uses and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and  
receiver.  
Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
Consult the dealer or an experienced radio/ TV technician  
for help.  
This device complies with part 15 of the FCC Rules. Operation  
is subject to the following two conditions:  
 
II  
1This device may not cause harmful interference.  
2This device must accept any interference received,  
including interference that may cause undesired operation.  
Any changes or modifications not expressly approved by the  
party responsible for compliance could void the user’s authority  
to operate the equipment.  
CE Mark Warning  
This is a class B product. In a domestic environment, this  
product may cause radio interference, in which case the user  
may be required to take adequate measures.  
Safety Notices  
Cautions:  
Do not use this product near water, for example, in a wet  
basement or near a swimming pool.  
Avoid using this product during an electrical storm. There may  
be a remote risk of electric shock from lightning.  
 
III  
Package Contents  
The following items should be found in your package:  
¾
¾
¾
One TL-SG1005D/TL-SG1008D Switch  
One Power Adapter  
This User Guide  
Note:  
The wall-mounting screws are not provided with our product.  
Please contact your distributor if any of the listed items are  
damaged or missing.  
Convention  
The Switch or TL-SG1005D/TL-SG1008D mentioned in this  
User Guide stands for TL-SG1005D/TL-SG1008D 5/8-port  
Gigabit Desktop Switch without any explanation.  
Note:  
The two devices of TL-SG1005D and TL-SG1008D are sharing  
this User Guide. For simplicity, we will take TL-SG1008D for  
example throughout this Guide.  
The differences between them are:  
¾
TL-SG1005D Switch with  
Negotiation RJ45 ports.  
5
10/100/1000Mbps Auto-  
10/100/1000Mbps Auto-  
¾
TL-SG1008D Switch with  
Negotiation RJ45 ports.  
8
1
 
Chapter 1 Introduction of the Product  
Thank you for choosing the TL-SG1005D/TL-SG1008D 5/8-port  
Gigabit Desktop Switch.  
1.1 Overview of the Product  
Powered by the Gigabit Ethernet Technology, TL-SG1005D/  
TL-SG1008D Gigabit Desktop Switch provides the seamless  
network connection, which can speed up your old network to  
1000Mbps, ensuring the graphics, CGI, CAD, or multimedia  
files and other applications with bandwidth-intensive files  
transferred across the network almost instantly.  
The non-blocking switching architecture adopted in the TL-  
SG1005D/TL-SG1008D switch greatly improves network  
response times as well as significantly speed up the traffic  
between subnets by forwarding and filtering packets at full wire-  
speed for maximum throughput.  
The TL-SG1005D/TL-SG1008D switch is plug-and-play. In  
addition, the Auto-MDI/MDIX cable detection on all ports  
eliminates the demand of crossover cable or Uplink port. Each  
port can be used as general ports or Uplink ports, and any port  
can be simply plugged into a server, a hub, a router, a switch or  
a PC, using the straight cable or crossover cable. Diagnostic  
LEDs which display link status and activity, allowing you to  
quickly detect and correct problems on the network.  
The TL-SG1005D/TL-SG1008D switch adopts Green Ethernet  
technology, supports power saving features. The switch  
automatically powers down the ports that have no link or are  
connected to the computers which have been shut down,  
budgets power output for different Ethernet cable lengths.  
2
 
1.2 Features  
¾
¾
¾
¾
¾
¾
Supports Green Ethernet technology to implement power  
saving features  
Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab  
standards  
5/8 10/100/1000Mbps Auto-Sensing RJ45 ports supporting  
Auto-MDI/MDIX  
Supports IEEE802.3x flow control for Full-duplex Mode and  
backpressure for Half-duplex Mode  
Non-blocking switching architecture that forwards and filters  
packets at full wire-speed for maximum throughput  
4K entry MAC address table of TL-SG1005D/TL-SG1008D  
with auto-learning and auto-aging  
¾
¾
¾
Supports for Jumbo frames of up to 9KB  
LED indicators for monitoring power, link, speed and activity  
External power adapter supply  
Chapter 2 Identifying External Components  
This Chapter describes the front panel and rear panel of the  
Switch.  
2.1 Front Panel  
Figure 2-1 TL-SG1008D Switch Front Panel  
3
 
The Switch’s LEDs are located on the front panel:  
¾ Power LED: This indicator will light up when the Switch  
powers up.  
¾ LEDs (1~8): The LED indicates Link/Active status. The  
corresponding LED indicator will light solid green when  
connected to a network device. It flashes green when data is  
being transmitted or received on the working connection.  
Note:  
The LEDs’ description above explains the device’s working  
status after initialization.  
2.2 Rear Panel  
Figure 2-2 TL-SG1008D Switch Rear Panel  
The following parts are located on the rear panel.  
¾
POWER: The POWER socket is where you will connect the  
power adapter. Please use the power adapter provided with  
this TL-SG1008D Switch.  
¾
Port (1-8): The TL-SG1008D Switch is equipped with 8  
10/100/1000Mbps Auto-Sensing RJ45 ports where you will  
connect your network devices. The working status can be  
indicated by the corresponding LEDs on the front panel.  
4
 
Chapter 3 Installation  
The Switch can be either located on a desktop or mounted on a wall.  
3.1 Mounting the Switch on a Desk  
To locate the Switch on a desktop, please follow these steps:  
1) Place the Switch on a flat desk.  
2) Inspect the Power Adapter carefully and make sure that it  
is properly connected to a power source.  
3) Ensure adequate ventilation space around the switch for  
dissipating heat and air.  
Note:  
Please avoid any heavy thing placed on the switch.  
To ensure the stable cable connection, please keep the switch  
horizontal on the desktop, with white cover facing up.  
3.2 Mounting the Switch on a Wall  
There are two wall-mounting slots on the bottom panel of the  
Switch. To mount the Switch on a wall, please follow the steps  
below.  
1) Drill two holes into the wall. Insert a screw into each hole  
and leave a part of its head exposed.  
2) Place the two wall-mounting slots over the screws and  
slide the Switch down to fasten it.  
5
 
3.3 Power On  
Power on the Switch and it will automatically initialize and its  
LED indicators will respond as follows:  
Time  
Status Indication  
Name  
Power All the time On  
Power on  
N/A  
1st second  
2nd second  
On  
Off  
N/A  
LEDs  
(port  
1-8)  
No device connected to the  
corresponding port.  
Off  
On  
3
rd second~  
There is a 10/100/1000Mbps  
device connected to the  
corresponding port.  
Note:!  
If the LED indicators don’t respond as described above, please  
check the power supply and its connection.  
6
 
Appendix A: Specifications  
General  
Standards  
IEEE802.3, IEEE802.3u, IEEE802.3ab  
Topology  
Protocol  
Star  
CSMA/CD  
Ethernet: 10Mbps (Half Duplex), 20Mbps  
(Full Duplex)  
Fast Ethernet: 100Mbps (Half Duplex),  
200Mbps (Full Duplex)  
Data Transfer Rate  
Gigabit Ethernet: 2000Mbps (Full Duplex)  
10Base-T: UTP category 3, 4, 5 cable  
(maximum 100m) EIA/TIA-568 100STP  
(maximum 100m)  
100Base-TX: UTP category 5, 5e cable  
(maximum 100m) EIA/TIA-568 100STP  
(maximum 100m)  
Network Media(Cable)  
Number of Ports  
1000Base-T: UTP category  
5
cable  
(maximum 100m) EIA/TIA-568 100STP  
(maximum 100m)  
5/8 10/100/1000Mbps Auto-Negotiation  
RJ45 ports  
LED indicators  
Power, LEDs (1-8)  
Store-and-Forward  
Transfer Method  
MAC Address Learning Automatically learning, automatically aging  
10Base-T: 14880pps/Port  
100Base-Tx: 148800pps/Port  
1000Base-T: 1488000pps/Port  
Frame Filter Rate  
7
 
10Base-T: 14880pps/Port  
Frame Forward Rate  
100Base-Tx: 148800pps/Port  
1000Base-T: 1488000pps/Port  
Environmental and Physical  
Operating Temperature 0 ~40(32 ~104)  
Storage Temperature  
Operating Humidity  
Storage Humidity  
-40 ~70(-40 ~158)  
10%~90% non-condensing  
5%~90% non-condensing  
Appendix B: Troubleshooting  
1. The Power LED is not lit  
Check to see if the AC power cord is connected to the  
Switch properly, and make sure the power source is ON.  
2. The Link/Act LED is not lit when a device is connected  
to the corresponding port  
Check to see if the cable connectors are firmly plugged into  
the Switch and the device, and verify the connected device  
is turned on and working well. Make sure the cable is not  
longer than 100 meters (328 feet).  
8
 

The Singing Machine Flat Panel Television STVG 535 User Manual
Timex Watch W279 User Manual
Toshiba Laptop 1600EP User Manual
Toshiba Network Card TOS SN 1 User Manual
Toshiba Printer Accessories MJ 1103 User Manual
Trane Air Conditioner Central Air Conditioning User Manual
Transcend Information Computer Drive Memory Stick Reader Writer User Manual
Vantec Range NST 530U2 User Manual
VDO Dayton Car Satellite TV System DTV 6500 User Manual
Vector Camping Equipment VEC1198POB User Manual