Quick Installation Guide
TPL-210AP
85Mbps Powerline
Wireless Access
(TPL-210AP)
Outlet
Workstation with
Fast Ethernet PCI Adapter
(TE100-PCIWN)
85Mbps Powerline
Fast Ethernet Bridge
(TPL-202E)
Outlet
Workstation with
Wireless PCI Adapter
(TEW-423PI)
Notebook with
Wireless PC Card
(TEW-421PC)
Internet
Cable/DSL
Modem
4-Port Cable/DSL
Broadband Router
(TW100-S4W1CA)
85Mbps Powerline
Fast Ethernet Bridge
(TPL-202E)
Outlet
54Mbps Wireless
Powerline
10/100Mbps
Troubleshooting
Q1: How do I configure TCP/IP settings on my computer?
1. Go into the Control Panel and double-
click the Network Connections icon,
right-click the Local Area Connection
icon and then click Properties.
2. Click Internet Protocol (TCP/IP) and
then click Properties. Then click on
Use the following IP address, and
make sure you assign your network
adapter an IP address in the subnet of
192.168.1.x.
Address Bar, but an error message says "The page cannot be displayed". How
can I get into the TPL-210AP's web configuration page?
A2: First, check your hardware settings again by following the instructions in
section 2. Second, make sure the Power, Home Plug and Wireless lights are lit.
Third, make sure the TCP/IP settings are configured properly (see Q1). Fourth,
since the Access Point's default IP address is 192.168.1.200, make sure that no
other network devices are assigned an IP address of 192.168.1.200.
Q3: If my network's IP is different than the Access Point's range, what should I
do?
A3: You should still configure the Access Point first. After all the settings are
applied, go to the Access Point's configuration page, click on IP setting and
change the IP address of the Access Point to match your network's IP.
6
Q4: After I successfully configured the Access Point to meet my network settings,
I can not connect to my network using wireless computers.
A4: First, if you are connecting to an existing Powerline network, the Powerline
network name one the Access Point must match that of the Powerline network. To
configure the Powerline network name, log on to the Access Point's browser
Click HomePlug. Change the HomePlug Group name to match your network's
Powerline network name. The default HomePlug Group name is HomePlug.
Second, verify that the power outlet the TPL-210AP is plugged into is on the same
electrical power distribution and/or circuit breaker. Third, if you have a DHCP
server in your network, you need to go into TCP/IP settings again and re-select
"Obtain an IP address automatically" to allow the PC to regain an IP address from
your DHCP server.
Q5: All the settings are correct, but I can not make a wireless connection to the
Access Point.
A5: First, double check that the Wireless light on the Access Point is lit. Second,
power cycle the Access Point. Disconnect the Access Point from the power outlet,
wait 15 seconds, then plug the Access Point back into the power outlet. Third,
contact the manufacturer of your wireless network adapter. Make sure the
wireless network adapter is configured with the proper SSID. The default SSID of
the Access Point is Powerline.
If you still encounter problems or have any questions regarding the TPL-210AP, please
contact TRENDnet's Technical Support Department.
7
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.
TRENDnet Technical Support
.
US Canada
Toll Free Telephone: 1(866) 845-3673
24/7 Tech Support
.
.
.
.
.
Europe (Germany France Italy Spain Switzerland UK)
Toll Free Telephone: +00800 60 76 76 67
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Worldwide
Telephone: +(31) (0) 20 504 05 35
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Product Warranty Registration
Please take a moment to register your product online.
20675 Manhattan Place
Torrance, CA 90501
USA
Copyright ©2007. All Rights Reserved. TRENDnet.
|