TRENDnet Network Card TEW 430APB User Manual

Quick Installation Guide  
TEW-430APB  
 
1. Before You Start  
Package Content  
TEW-430APB  
Quick Installation Guide  
User’s Guide CD-ROM  
External Power Adapter  
1 x 2dBi Detachable Antenna  
Installation Requirements  
Web Browser: Internet Explorer (5.5 or higher) or  
Netscape Navigator (4.7 or higher).  
A computer with a network adapter properly installed.  
A network Switch or Hub with an available network LAN port.  
A RJ-45 network cable.  
Application  
54Mbps 802.11g Wireless LAN Access Point  
(TEW-430APB)  
Workstation with  
Wireless PCI Adapter  
(TEW-423PI)  
Notebook with  
Wireless PC Card  
(TEW-421PC)  
Internet  
Cable/DSL  
Modem  
Cable/DSL 4-Port  
Firewall Router  
(TW100-BRF114)  
Workstation with  
PCI Adapter  
(TE100-PCIWN)  
1
 
English  
2. Hardware Installation  
Note: Locate an optimum location for the Access Point. The best place for the  
Access Point is usually at the center of your wireless network. Please connect  
the computer configuring the TEW-430APB to the same switch/hub.  
1. Connect a RJ-45 cable from the  
Switch/Hub to the LAN port of the  
Access Point and then connect the  
2dBi Detachable Antenna.  
2. Connect the Power Adapter to the  
Access Point and then to a power  
outlet.  
3. Verify that the following front panel  
lights are on: WLAN and LAN.  
2
 
English  
3. Configure the Access Point  
Note: It is recommended that you configure the Access Point from a wired  
computer. Before the Access Point can be configured, a Static IP address  
must be assigned to your computer's network adapter in the subnet of  
192.168.1.x. Since the Access Point's default IP address is 192.168.1.100,  
make sure no other network devices are assigned an IP address of  
192.168.1.100. (Refer to the Troubleshooting section on how to configure  
TCP/IP settings on your PC)  
1. Open your web browser, type  
Address bar, and press Enter.  
2. Enter User name and Password,  
and then click OK. By default,  
User name: admin  
Password: admin  
3. Click Wizard.  
3
 
English  
4. Click Next.  
5. Enter a new password for your  
Access Point, verify the new  
password, and then click Next. (If a  
new password is not entered, the  
default password admin will be  
used.  
6. Enter a SSID for your Access  
Point and then click Next.  
4
 
English  
7. Enable Encryption if needed and  
then click Next.  
8. Click Restart.  
9. Click Close.  
Your installation is now complete.  
For detailed information regarding the TEW-430APB's configuration and  
advanced settings, please refer to the Troubleshooting section, User's Guide  
5
 
English  
Troubleshooting  
Q1: How do I configure TCP/IP settings on my computer?  
1. Go into the Control Panel and double-  
click the Network Connections icon,  
right-click the Local Area Connection  
icon and then click Properties.  
2. Click Internet Protocol (TCP/IP) and  
then click Properties. Then click on  
Use the following IP address, and  
make sure you assign your network  
adapter an IP address in the subnet of  
192.168.1.x.  
error message says “The page cannot be displayed.” How can I get into the  
TEW-430APB's web configuration page?  
A2: First, check your hardware settings again by following the instructions in  
section 2. Second, make sure the LAN and WLAN lights are lit. Third, make sure  
the TCP/IP settings are configured properly (see Q1). Fourth, since the Access  
Point's default IP address is 192.168.1.100, make sure that no other network  
devices are assigned an IP address of 192.168.1.100.  
Q3: If my network's IP is different than the Access Point's range, what should I  
do?  
A3: You should still configure the Access Point first. After all the settings are  
applied, go to the Access Point's configuration page, click on TCP/IP settings and  
change the IP address of the Access Point to match your network's IP.  
6
 
Q4: After I successfully configured the Access Point to meet my network settings,  
I can not connect to my network using wireless computers.  
A4: If you have a DHCP server in your network, you need to go into TCP/IP  
settings again and re-select "Obtain an IP address automatically" to allow the PC  
to regain an IP address from your DHCP server.  
Q5: All the settings are correct, but I can not make a wireless connection to the  
Access Point.  
A5: First, double check that the WLAN light on the Access Point is lit. Second,  
power cycle the Access Point by unplugging the power to the Access Point. Wait  
15 seconds, then plug the power back in. Third, contact the manufacturer of your  
wireless network adapter. Make sure the wireless network adapter is configured  
with the proper SSID. The default SSID of the Access Point is TRENDnet.  
If you still encounter problems or have any questions regarding the TEW-430APB,  
please contact TRENDnet's Technical Support Department.  
7
 
Certifications  
This equipment has been tested and found to comply with FCC and CE Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference.  
(2) This device must accept any interference received. Including interference that may cause undesired  
operation.  
Este equipamento opera em caráter secundário, isto é, não tem  
direito a proteção contra interferência prejudicial, mesmo de estações  
do mesmo tipo, e não pode causar interferência a sistemas operando  
em caráter primário.  
Waste electrical and electronic products must not  
be disposed of with household waste. Please  
recycle where facilities exist. Check with you Local  
0873-05-2375  
Authority or Retailer for recycling advice.  
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV  
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS  
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO  
OPERATE THE EQUIPMENT.  
ADVERTENCIA  
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de  
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al  
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador  
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria  
existente en el pais o zona de instalación.  
 
TRENDnet Technical Support  
.
US Canada  
Toll Free Telephone: 1(866) 845-3673  
24/7 Tech Support  
.
.
.
.
.
Europe (Germany France Italy Spain Switzerland UK)  
Toll Free Telephone: +00800 60 76 76 67  
English/Espanol - 24/7  
Francais/Deutsch - 11am-8pm, Monday - Friday MET  
Worldwide  
Telephone: +(31) (0) 20 504 05 35  
English/Espanol - 24/7  
Francais/Deutsch - 11am-8pm, Monday - Friday MET  
Product Warranty Registration  
Please take a moment to register your product online.  
20675 Manhattan Place  
Torrance, CA 90501  
USA  
 
Copyright ©2006. All Rights Reserved. TRENDnet.  

Toastmaster Coffeemaker ME8TSB ME8TPWCAN User Manual
Trane Air Conditioner FIN PRC004 User Manual
Tripp Lite Surge Protector DEU2 TEL User Manual
Tripp Lite Surge Protector Kiosk User Manual
Vermont Casting Electric Heater 2478 User Manual
Viking Convection Oven VHSO205 User Manual
Viking Ventilation Hood DIPR101R User Manual
Vinotemp Refrigerator VT 38 User Manual
Viper Automobile Alarm 791XV User Manual
VTech Cordless Telephone t2151 User Manual