Targus Mouse paum005 User Manual

ATTENTION! Targus Wireless RF Mouse Users  
Before You Begin  
After your computer detects the USB receiver and the driver software is installed, you must establish a communications link between the mouse and its receiver  
BEFORE you can use the mouse. To establish this link, you need to set the identification code so that the mouse works properly. To do this, follow the instructions  
for your mouse model.  
NOTE: This addendum replaces the section titled Establishing a Communications Link (All RF Mouse Models)” in the supplied user’s guide.  
Mouse Model PAUM005  
Mouse Model PAUM006  
Establishing a Communications Link  
Establishing a Communications Link  
Make sure that your computer is turned on and has detected the USB receiver  
before you establish a communications link.  
1
Press and release the link button on the receiver.  
1
Press and release the link button on the receiver.  
Link button/  
status light  
Link  
button  
Receiver link button (PAUM005)  
The receiver’s status light glows blue when the receiver is activated.  
Press and release the reset button, located on the bottom of the mouse.  
2
Receiver link button (PAUM006)  
CAUTION: Pressing and holding the reset button longer than 1.5 seconds  
may cause the mouse to enter power off mode. See Powering the Mouse  
2
Press and release the link button, located on the bottom of the RF  
mouse.  
Link  
button  
Reset  
button  
Mouse link button (PAUM006)  
Mouse reset button (PAUM005)  
The receiver’s status light flashes red once the mouse and receiver are  
activated and whenever there is mouse activity.  
The mouse’s red light emitter diode (LED) stops glowing when you  
press the reset button and resumes glowing when the button is  
released.  
NOTE: You may need to press the mouse’s link button more than once if the  
receiver’s status light does not glow red.  
You are now ready to use the RF mouse.  
The receiver’s status light flashes while it scans the identification  
codes for the mouse. Once a valid code is selected, the status light  
stops flashing.  
Powering the Mouse Off and On  
To power off the mouse:  
3
To use the mouse, press any button.  
1
2
3
Press any key to wake the mouse (if it’s in sleep mode).  
Press and hold the reset button for at least two seconds.  
Release the reset button when the red LED flashes one time.  
The mouse is now in power off mode and cannot be used. To power on the  
mouse, press and release the reset button so that the red LED glows. You can  
now use the mouse again.  
Things to Remember  
Batteries  
General  
PAUM005  
PAUM006  
• You must establish a communications link every time • You should change the batteries when the LED on the • You should change the batteries every two to three  
you change the batteries.  
scroller wheel glows blue.  
months, depending on how often you use the mouse.  
• To extend the life of your batteries, remove them  
from the mouse while traveling.  
• The mouse enters sleep mode every time the batteries  
are changed. To wake the mouse from sleep mode,  
press any button.  
Sleep Mode  
• The mouse’s sleep mode feature activates after 20 minutes of non-operation.  
• To wake the mouse from sleep mode, press any button.  
402-0250-001B  
 
 

Tatung Flat Panel Television TLM 1705 User Manual
Toshiba TV DVD Combo MD13N1 User Manual
Tricity Bendix Dishwasher DH 101 User Manual
Tripp Lite Computer Accessories PK3020KB User Manual
Ultratec Printer CLB 2012 User Manual
Unisar Thermometer Digital Thermometer User Manual
Vector Portable Generator VEC097 User Manual
Vulcan Hart Oven CO1717 User Manual
Weed Eater Blower 952711937 User Manual
Weed Eater Lawn Mower 96114000410 User Manual