Tascam Musical Instrument PORTA02 User Manual

»
OWNER’S MANUAL  
9101411800  
 
Important Safety Instructions  
CAUTION:  
"Note to CATV system installer:  
Read all of these Instructions.  
Save these Instructions for later use.  
Follow all Warnings and Instructions marked on the  
audio equipment.  
This reminder is provided to call the CATV system installer’s  
attention to Section 820-40 of the NEC which provides guide-  
lines for proper grounding and, in particular, specifies that the  
cable ground shall be connected to the grounding system of the  
building, as close to the point of cable entry as practical.  
1) Read Instructions — All the safety and operating  
instructions should be read before the product is operated.  
2) Retain Instructions — The safety and operating instruc-  
tions should be retained for future reference.  
Example of Antenna Grounding as per  
National Electrical Code, ANSI/NFPA 70  
3) Heed Warnings — All warnings on the product and in the  
operating instructions should be adhered to.  
4) Follow Instructions — All operating and use instruc-  
tions should be followed.  
5) Cleaning — Unplug this product from the wall outlet  
before cleaning. Do not use liquid cleaners or aerosol cleaners.  
Use a damp cloth for cleaning.  
ANTENNA  
LEAD IN  
WIRE  
GROUND  
CLAMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
6) Attachments — Do not use attachments not recommend-  
ed by the product manufacturer as they may cause hazards.  
7) Water and Moisture — Do not use this product near  
ELECTRIC  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
_
water for example, near a bath tub, wash bowl, kitchen sink,  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250. PART H)  
or laundry tub; in a wet basement; or near a swimming pool;  
and the like.  
NEC - NATIONAL ELECTRICAL CODE  
8) Accessories — Do not place this product on an unstable  
cart, stand, tripod, bracket, or table. The product may fall, caus-  
ing serious injury to a child or adult, and serious damage to the  
product. Use only with a cart, stand, tripod, bracket, or table  
recommended by the manufacturer, or sold with the product.  
Any mounting of the product should follow the manufacturer’s  
instructions, and should use a mounting accessory recommend-  
ed by the manufacturer.  
15) Lightning — For added protection for this product during  
a lightning storm, or when it is left unattended and unused for  
long periods of time, unplug it from the wall outlet and discon-  
nect the antenna or cable system. This will prevent damage to  
the product due to lightning and power-line surges.  
16) Power Lines — An outside antenna system should not be  
located in the vicinity of overhead power lines or other electric  
light or power circuits, or where it can fall into such power lines  
or circuits. When installing an outside antenna system, extreme  
care should be taken to keep from touching such power lines or  
circuits as contact with them might be fatal.  
9) A product and cart combination should be moved with care.  
Quick stops, excessive force, and uneven surfaces may cause  
the product and cart combination to overturn.  
17) Overloading — Do not overload wall outlets, extension  
cords, or integral convenience receptacles as this can result in  
risk of fire or electric shock.  
18) Object and Liquid Entry — Never push objects of any  
kind into this product through openings as they may touch dan-  
gerous voltage points or short-out parts that could result in a  
fire or electric shock. Never spill liquid of any kind on the prod-  
uct.  
19) Servicing — Do not attempt to service this product your-  
self as opening or removing covers may expose you to danger-  
ous voltage or other hazards. Refer all servicing to qualified  
service personnel.  
20) Damage Requiring Service — Unplug this product  
from the wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
a) when the power-supply cord or plug is damaged.  
b) if liquid has been spilled, or objects have fallen into the  
product.  
c) if the product has been exposed to rain or water.  
d) if the product does not operate normally by following the  
operating instructions. Adjust only those controls that are cov-  
ered by the operating instructions as an improper adjustment of  
other controls may result in damage and will often require  
extensive work by a qualified technician to restore the product  
to its normal operation.  
10) Ventilation — Slots and openings in the cabinet are pro-  
vided for ventilation and to ensure reliable operation of the  
product and to protect it from overheating, and these openings  
must not be blocked or covered. The openings should never be  
blocked by placing the product on a bed, sofa, rug, or other sim-  
ilar surface. This product should not be placed in a built-in  
installation such as a bookcase or rack unless proper ventilation  
is provided or the manufacturer’s instructions have been  
adhered to.  
11) Power Sources — This product should be operated only  
from the type of power source indicated on the marking label.  
If you are not sure of the type of power supply to your home,  
consult your product dealer or local power company. For prod-  
ucts intended to operate from battery power, or other sources,  
refer to the operating instructions.  
12) Grounding or Polarization — This product may be  
equipped with a polarized alternating-current line plug (a plug  
having one blade wider than the other). This plug will fit into  
the power outlet only one way. This is a safety feature. If you  
are unable to insert the plug fully into the outlet, try reversing  
the plug. If the plug should still fail to fit, contact your electri-  
cian to replace your obsolete outlet. Do not defeat the safety  
purpose of the polarized plug.  
13) Power-Cord Protection — Power-supply cords should  
be routed so that they are not likely to be walked on or pinched  
by items placed upon or against them, paying particular atten-  
tion to cords at plugs, convenience receptacles, and the point  
where they exit from the product.  
e) if the product has been dropped or damaged in any way.  
f ) when the product exhibits a distinct change in performance  
_
this indicates a need for service.  
21) Replacement Parts — When replacement parts are  
required, be sure the service technician has used replacement  
parts specified by the manufacturer or have the same character-  
istics as the original part. Unauthorized substitutions may result  
in fire, electric shock, or other hazards.  
22) Safety Check — Upon completion of any service or  
repairs to this product, ask the service technician to perform  
safety checks to determine that the product is in proper operat-  
ing condition.  
23) Wall or Ceiling Mounting — The product should be  
mounted to a wall or ceiling only as recommended by the man-  
ufacturer.  
24) Heat — The product should be situated away from heat  
sources such as radiators, heat registers, stoves, or other prod-  
ucts (including amplifiers) that produce heat.  
14) Outdoor Antenna Grounding — If an outside antenna  
or cable system is connected to the product, be sure the anten-  
na or cable system is grounded so as to provide some protection  
against voltage surges and built-up static charges. Article 810 of  
the National Electrical Code, ANSI/NFPA 70, provides infor-  
mation with regard to proper grounding of the mast and sup-  
porting structure, grounding of the lead-in wire to an antenna  
discharge unit, size of grounding conductors, location of anten-  
na-discharge unit, connection to grounding electrodes, and  
requirements for the grounding electrode.  
3
 
1 An introduction to the Porta02  
1 – An introduction to the Porta02  
The TASCAM Porta02 MiniStudio recording” before you start using the  
are not possible with an ordinary stereo now will save you a lot of time in the  
cassette recorder.  
future. You can read the rest of the man-  
ual at any time.  
We suggest that you read at least this sec-  
tion 1 and also 3, “Making your first  
1.1 Multitrack recording – a brief introduction  
This section gives you a brief introduc- to read through this section so that you  
tion to some of the terms and techniques understand the rest of the manual, which  
used in recording. If you are unfamiliar uses the terms explained here.  
with these terms, you may find it useful  
1.1.1 Multitrack recorders  
When you listen to a commercial record- The Porta02 allows you to record up to 4  
ing (CD, cassette, etc.), it is quite proba- tracks on inexpensive Type II (chrome)  
ble that the different parts of the piece cassettes using the same principle as  
will have been recorded at different larger studios–taking inputs into  
a
times.  
mixer’s channels, feeding them into a  
recorder which can record tracks inde-  
pendently of each other, and building up  
the song by recording new tracks while  
listening to what has been recorded  
before (“monitoring”).  
This is done by “multitracking”–taking  
the different sounds, feeding them  
through a mixer’s inputs (“channels”) and  
recording them on a special tape recorder  
which splits the tape into “stripes”, each  
stripe being used for a different part of The advantage of working with multi-  
the music.  
track recording is that the whole group of  
musicians does not have to repeat the  
whole piece if one person makes a mis-  
take.  
These stripes are called “tracks”, and the  
parts recorded on them may also be  
called “tracks”. Since there are many  
tracks on a tape, the term “multitrack” is The illustration below shows you how  
used to describe these tapes and record- tracks are arranged on an ordinary stereo  
ers.  
cassette tape, as well as on the Porta02  
4
 
1 An introduction to the Porta02  
and on A/V cue-equipped cassette record-  
ers.  
L
R
4
3
CUE  
R
L
2
1
R
L
IEC (Philips) ste-  
reo cassette  
TASCAM 4Tr 4Ch  
(Porta02 format)  
TASCAM 4Tr 3Ch  
(A/V cue format)  
Notice that the stereo cassette arrange- one pair of L and R tracks on the stereo  
ment allows you to use both sides of the cassette take up the same positions as  
cassette, by playing the tape in the other tracks 1 and 2 on the Porta02. This can be  
direction. The Porta02, however, uses the important for your recording projects, as  
whole width of the tape. Notice also that we will see later on.  
1.1.2 Mixing down  
Another advantage of multitrack record- using the panpots, you can make the  
ing is that when you come to make the tracks appear to come from the left or the  
final version (on CD, cassette, etc.), you right speakers or anywhere in the middle.  
can adjust the level (volume) of each  
The technique of converting a multitrack  
track, so that the piece sounds the way  
recording to a stereo recording is called  
you want.  
“mixing down” to a “stereo master” or  
As well as adjusting the track levels, you “mastering” recorder. The Porta02  
can also adjust the position of each track includes a mixdown section which allows  
with regard to the left and right speakers. you to mix to a stereo cassette or MD  
This is called “panning”, and the controls recorder.  
used to do this are called “panpots”. By  
1.2 Some safety notes and precautions  
Always use the PS-P2 power adaptor  
supplied with the Porta02. If you use  
any other adaptor, there is a risk of  
damage, or even fire. Make sure that  
the input voltage marked on the PS-P2  
adaptor matches the power supply you  
are using. If you are in any doubt, con-  
sult your TASCAM dealer.  
Turn off your Porta02 and remove the  
cassette when you are not using the  
Porta02. If you will not be using it for  
an extended period of time, unplug the  
PS-P2 adaptor.  
When connecting or disconnecting the  
Porta02 to or from any other equip-  
ment, make sure the power to the  
Porta02 and all other equipment is  
turned off. This will avoid possible  
damage to equipment.  
Do not keep your Porta02 in a very  
hot place. Remember that in sunny  
weather, the inside of a parked car  
heats up very quickly. Avoid leaving  
your Porta02 in such a place.  
Do not spill liquid onto your Porta02.  
Avoid eating, drinking and smoking  
near it (smoke particles are bad for  
5
 
1 An introduction to the Porta02  
audio equipment). If any liquid or any  
objects such as paperclips, guitar  
picks, etc. fall inside the Porta02, do  
not try to operate it. Return it to a  
TASCAM service center for repair.  
If the case of the Porta02 becaomes  
dirty, clean it only with a damp (not  
wet) cloth, moistened with a little  
detergent. Do not use solvents or thin-  
ners, etc. to clean the Porta02, as these  
will damage the surface.  
There are no parts inside the Porta02  
that you can repair by yourself. Do not  
open the Porta02 case or try to make  
any repairs. Return it to a TASCAM  
service center for repair.  
1.2.1 Tape cassettes  
Since the Porta02 uses the whole width of To avoid having to wind and rewind a lot  
a cassette tape, you can only play and use of tape, use the shortest possible cassettes  
one side of a cassette. You should try to for your projects. Remember that because  
use either side A or side B for all cas- you are only using one side of the cas-  
settes, to avoid confusion when changing sette, the marked length of the tape will  
tapes.  
be halved (that is, a C60 tape will run for  
30 minutes, a C40 for 20 minutes, etc.).  
Only use Type II (chrome or CrO ) cas-  
2
settes with the Porta02. Find a reliable  
brand and stick with it. The time you  
spend creating your multitrack master is  
worth much more than the small differ-  
ence in price between cheap and high-  
quality cassettes. High quality cassettes  
will cause you fewer problems in the long  
run.  
NOTE  
Never use C120 cassettes with the Porta02. The  
tape in these cassettes is thin, and may stretch  
and break.  
Always store cassettes in a safe place  
(away from the magnetic fields produced  
by speakers, television sets, computer  
monitors, etc.).  
1.2.2 Record-protecting cassettes  
The record-protect tab on a cassette stops However, we suggest that you remove  
you recording on that side when it is both tabs when you want to protect a  
removed. The Porta02 also recognizes Porta02 cassette. This will stop you put-  
this protection, and will not allow you to ting in the cassette the wrong way round  
record on the side of a cassette where this and recording over old material  
tab has been removed.  
accidentally.  
1.2.3 Playing back stereo cassettes  
As mentioned earlier, the Porta02 can be played back on a stereo cassette  
play back cassettes recorded on a stereo recorder.  
cassette recorder, using tracks 1 and 2.  
Also, note that if a cassette has been  
Also, if tracks 1 and 2 have been recorded  
recorded with noise reduction, such as  
on the Porta02, these cassettes can be  
Dolby, etc., it will sound strange when  
played back on a stereo cassette recorder.  
played back on the Porta02. Any tapes  
However, if tracks 3 and 4 are used for (tracks 1 and 2) recorded on the Porta02  
recording on the Porta02, these cannot should be played back without noise  
reduction on a stereo recorder.  
6
 
1 An introduction to the Porta02  
1.2.4 Cleaning the heads  
You should clean the tape heads of the formance and longer life from your  
Porta02 regularly to keep it working Porta02.  
properly. Dirt and tape oxide buildup on  
the heads will force the tape away from  
the tape head gaps that record and play-  
back. Head cleaner will remove the dirt  
and restore the sound quality.  
WARNING  
Only use head and rubber cleaning fluid and  
cleaning swabs designed for use with tape  
recorders. The use of any other cleaning materi-  
als may cause damage to the Porta02.  
In addition to affecting performance by  
coating the heads, and keeping the tape  
away from the recording and playback  
gaps, dirt and oxide in the tape path will  
also act in the same way as very fine  
sandpaper, which will wear down internal  
parts of the Porta02, and affect the  
recording in this way as well.  
Clean the heads and metal parts of the  
tape path before every session with the  
Porta02 and also after every session.  
Heads and tape  
guides  
All of these problems can be avoided if  
you buy a head cleaning kit such as the  
TEAC TZ-261 and keep it with your  
Porta02 for regular use. The kit consists  
of head cleaner, cleaner for the rubber  
parts of the Porta02, and cotton-tipped  
swabs. The cost of such a kit is less than  
the cost of a couple of high-quality cas-  
settes and will pay for itself in better per-  
Capstan  
Pinch wheel  
1) Open the tape cassette cover.  
2) Carefully clean the heads and  
metal parts as shown in the  
illustration using a swab dipped in  
the head cleaning fluid.  
3) Dry off the heads with a dry swab.  
1.2.5 Cleaning the pinch roller  
You should also clean the rubber pinch 3) Press a swab dipped in the rubber  
roller at regular intervals (at least once  
each day that you use the Porta02).  
cleaning fluid against the right side  
of the pinch roller.  
If you press the right side of the roller,  
the swab will not get caught between the  
roller and capstan.  
1) Open the tape cassette cover.  
2) Press the PLAY key.  
The pinch roller will engage with the  
capstan shaft and start turning.  
4) Dry the capstan with a dry swab  
and make sure that there is no  
material on the pinch roller or  
capstan before you insert a  
cassette.  
7
 
   
2 Parts of the Porta02  
1.3 What you need to make recordings  
Apart from the Porta02 itself, you will  
need:  
Some monitoring equipment (some  
kind of amplifier and speaker system).  
Headphones, if you intend doing any  
work with microphones. These will  
avoid acoustic feedback (“howl-  
round”) when recording. Additionally,  
headphones are sometimes useful  
when panning tracks on mixdown, as  
you can hear the precise position of  
each track.  
Some kind of stereo mastering  
recorder to produce the stereo record-  
ings. This can be a cassette recorder  
such as the TASCAM 102Mk II or an  
MD recorder such as the TASCAM  
MD301. A recorder which does not  
have recording level controls is not  
suitable for use as a master recorder.  
You will also need RCA (pin or  
phono) cables to connect the Porta02  
to other equipment.  
Of course, you will also need some  
kind of sound source to record (instru-  
ment or microphone, etc.).  
1.4 Connecting the Porta02  
1) Make sure all the equipment is  
turned off.  
You can listen to the Porta02 by selecting  
the amplifier’s input source to be from the  
terminals to which you connected the  
Porta02 (AUX or VIDEO, etc.).  
2) Connect the LINE OUT terminals of  
the Porta02 to the amplifier, using  
a pair of terminals on the amplifier  
such as AUX or VIDEO.  
When you have mixed down and you  
want to listen to the mixed tape, you  
should select the mastering recorder as  
the amplifier’s input source.  
NOTE  
Do not use any terminals marked PHONO or  
intended for record decks. These are connected  
to a special circuit inside the amplifier which  
makes them unsuitable for anything except  
record decks.  
Left  
speaker  
Right  
speaker  
3) Connect your mastering recorder  
to a set of four TAPE terminals on  
the amplifier (two for REC and two  
for PLAY).  
To AUX IN  
Amplifier  
TAPE OUT  
to  
PLAY OUT  
to  
REC IN  
LINE OUT  
Porta02  
You may be using an integrated system in  
which the mastering recorder and ampli-  
fier are built into one enclosure. In this  
case, you do not need to follow step 3.  
TAPE IN  
Mastering recorder  
2 – Parts of the Porta02  
This section gives an explanation of the they do.  
different parts of the Porta02, and what  
8
 
   
Parts of the Porta02  
Parts of the Porta02  
9
 
Parts of the Porta02  
[1]  
POWER IN and switch  
[4]  
PHONES jack  
This 1/4” jack allows you to connect a  
pair of stereo headphones to the Porta02.  
Use this jack to connect the PS-P2 AC  
adaptor which comes with your Porta02.  
When connecting the power, make sure  
the power switch is off (slide it to the  
right, as you look from the back).  
WARNING  
Do not use headphones equipped with a mono  
jack. This will cause damage to the Porta02’s  
headphone amplifiers.  
WARNING  
DO NOT use any adaptor with the Porta02  
except the PS-P2 adaptor which comes with the  
Porta02.  
[5]  
LINE OUT  
Use these RCA (pin or phono) jacks to  
connect your Porta02 to the amplifier or  
mastering recorder.  
Slide the switch to the left (looking from  
the back) to turn on the power to the  
Porta02.  
[6]  
PHONES LEVEL  
This control adjusts the volume in head-  
phones connected to the PHONES jack.  
Turn clockwise to increase the volume.  
There will be no output from the  
PHONES jack when the control is fully  
counter-clockwise. It has no effect on the  
level from the LINE OUT connectors.  
[2]  
MIC/LINE 2  
Use this 1/4” phone jack to connect the  
second channel audio source (instrument  
or microphone) to the Porta02.  
WARNING  
[7]  
MONO switch  
The Porta02 is designed to record signals from  
microphones, CD players, tape decks and musi-  
cal instruments. It is not designed to record sig-  
nals which come from the speaker outputs of  
any amplifier or equipment. If you try to plug  
such signals into the Porta02, you will almost  
certainly damage both the Porta02 and the other  
equipment.  
When this switch is pressed down (in), it  
changes the stereo signal from the  
PHONES jack into a mono signal (the  
same signal will be output from both the  
left and right channels). Press it again to  
return it to the “out” stereo position. It  
does not affect the signal from the LINE  
OUT connectors.  
[3]  
MIC/LINE 1 (MONO)  
[8]  
TRIM (1 and 2)  
Use this 1/4” phone jack to connect the  
first channel audio source (instrument or  
microphone) to the Porta02.  
Different pieces of equipment output sig-  
nals at different levels. The TRIM controls  
allow you to match the Porta02 to these  
levels. A piece of equipment such as a  
If you connect an audio source to this CD player or cassette deck will output  
jack, but do not connect a source to the signals at a high (LINE) level, so the trim  
MIC/LINE 2 jack, the source at this MIC/ control should be turned fully counter-  
LINE 1 jack acts as a mono source, that is, clockwise when such a device is being  
it will be split between the first and sec- recorded. A microphone on the other  
ond channels as if you had plugged the hand, produces a lower signal level, and  
same source into both jacks.  
so theTRIM control should be turned fully  
10  
 
Parts of the Porta02  
clockwise to MIC for any channel which  
is recording a microphone.  
When the PHONES MONO switch is  
pressed, these controls will have no effect  
on the output from the PHONES jack.  
Instruments such as electric guitars pro-  
LINE levels and the TRIM control should  
therefore be somewhere between fully  
clockwise and fully counter-clockwise.  
See 3.3, “Setting the level” for full details  
of how to adjust theTRIM controls for dif-  
ferent input sources.  
[13] REC FUNCTION switches  
(1 and 2)  
These switches control where the signals  
coming into the MIC/LINE jacks will be  
recorded. For both switches 1 and 2, the  
center position is marked as SAFE. When  
a switch is in this position, no signal will  
be recorded on tape. However, you can  
still listen to the signals coming into the  
MIC/LINE jacks and view the levels on the  
meters.  
[9]  
POWER indicator  
This yellow light is lit when the Porta02  
is connected to the power supply and  
switched on.  
When set to a number (1 or 3 for channel  
1, or 2 or 4 for channel 2), the signals  
input to the channel will be recorded on  
the track whose number has been set on  
the switch. This is called “assigning” or  
“routing” channels to tracks.  
[10] Tape counter and reset  
button  
The tape counter allows you to note dif-  
ferent parts of the tape and locate to  
them. Press the reset button to reset the  
counter to “000” at any time (we suggest  
that you only do this at the beginning of a  
recording).  
[14] Channel meters (1 and 2)  
Each channel has a set of four LED indi-  
cators which show the level of the signals  
sent to the LINE OUT L and R jacks.  
Exactly what is metered depends on the  
REC FUNCTION switch settings, but gen-  
erally, they display the signals at the MIC/  
LINE IN jacks, and when the input chan-  
nels are set to SAFE, the meters show the  
off-tape signals, whose levels and pan  
positions are set using the OUTPUT  
LEVEL and PAN controls.  
[11] OUTPUT LEVEL controls  
These controls change the levels of the  
four tape tracks in the LINE OUT and  
PHONES outputs. When one of these con-  
trols is turned fully counter-clockwise,  
the tape track corresponding to that con-  
trol will not be heard in the LINE OUT and  
PHONES outputs.  
[12] OUTPUT PAN controls  
The best level for any input signal is  
lights the red 0 indicator, and the +6 indi-  
cator (also red) is only lit by the loudest  
parts of the signal. See 3.3, “Setting the  
level” for details of how this should be set  
up.  
These controls change the position of the  
four tape tracks in the stereo LINE OUT  
and PHONES outputs. When one of these  
controls is turned fully counter-clock-  
wise, the sound of the corresponding tape  
track will appear to come from the left,  
and when turned fully clockwise, it will  
appear to come from the right. When in  
[15] Channel faders (1 and 2)  
the center position, the output will appear These faders are used to adjust the level  
equally from both the left and right.  
of the signals coming into the MIC/LINE  
11  
 
IN jacks. They should be used together  
with the TRIM controls (see 3.3, “Setting  
the level”) to adjust the levels of the sig-  
nals routed to the tape tracks.  
If the left record-protect tab of the cas-  
sette has been broken out, or if there is  
no cassette loaded, the RECORD key  
cannot be pressed.  
It is not possible to go directly from  
recording into playback mode.  
[16] RECORD indicator  
This red indicator lights when the  
RECORD and PLAY keys are pressed, and  
at least one of the REC FUNCTION  
switches is not in the SAFE position.  
The PAUSE key only pauses playback  
and recording. It is not possible to  
pause the tape in fast forward and  
rewind modes.  
All keys lock down when pressed,  
except for the STOP key, and only  
work when locked down.  
Pressing RECORD and PLAY while both  
REC FUNCTION switches are set to SAFE  
has the same effect as pressing PLAY.  
[18] Cassette compartment  
cover  
The hinged cassette compartment cover  
is opened by lifting the tab on the right  
side.  
[17] Transport controls  
These work in the same way as the con-  
trols on most cassette recorders. How-  
ever, there are a few points you should  
note:  
There is no eject mechanism. You load  
and unload cassettes by hand, using a fin-  
ger or fingers in the space to the right of  
the cassette.  
Pressing the RECORD key will also  
press down the PLAY key.  
12  
 
3 Making your first recording  
3 – Making your first recording  
This section describes how to make a 4-track recording using the  
Porta02. For this, we will assume that you are making a recording  
recording a part of a stereo CD or cassette on the other two tracks (3  
and 4). Make sure you know what you are going to say.  
Start by making sure that you have all the equipment listed in 1.3,  
“What you need to make recordings”.  
3.1 Setting up  
1) Make sure all equipment is turned off.  
2) Connect the LINE OUT jacks of the Porta02 to the AUX IN  
3) Connect the mastering recorder REC IN and PLAY OUT jacks  
to the appropriate jacks of the amplifier. See 1.4,  
“Connecting the Porta02” if you are not sure what you  
should be doing here.  
4) With the INPUT 1 fader at the 0 position, plug the  
microphone into the MIC/LINE 1 jack. Do not plug anything  
into the MIC/LINE 2 jack.  
If the microphone has a switch, make sure this switch is off.  
5) Plug the stereo headphones into the PHONES jack of the  
Porta02.  
6) Turn on the Porta02, the mastering recorder, and the  
amplifier (in that order).  
7) Set the amplifier’s input source to AUX (or the name of the  
3.2 Getting ready  
1) Clean the heads and pinch roller (see 1.2.4, “Cleaning the  
heads” and 1.2.5, “Cleaning the pinch roller”).  
2) Insert a Type II (chrome) cassette.  
The tape should be towards the front of the Porta02, and the full spool  
should be on the left side. Put the non-tape part of the cassette in first,  
and then push the tape (front) down into place  
13  
 
 
3 Making your first recording  
3) Play the tape for about 10 seconds and then stop the tape.  
4) Press the counter reset button.  
3.3 Setting the level  
The aim of this section is to teach you to set the input level so that  
the average signals coming from the microphone will light the 0  
meter indicator, and the loudest will light the +6 indicator.  
1) Make sure all OUTPUT LEVEL controls are set to 0. Put on  
the headphones and set the PHONES LEVEL to the 0 position.  
If you do not do turn down the speaker volume, you will probably get  
feedback (“howlround”) when you start using the microphone.  
2) Set both TRIM controls to the LINE position.  
Although you will probably end up with this control at the MIC posi-  
tion, or close to it, for now, set it to LINE.  
3) Take the INPUT 2 fader to the 0 mark. Bring the INPUT 1  
fader up to between the 7 and 8 marks.  
This is called the “nominal” position, and is the position where the  
electronics controlled by the fader will not have to amplify the signal  
too much (causing noise) or have too much signal going into them  
(causing distortion).  
4) Switch the microphone on if necessary. Speak into the  
microphone at the volume you will be recording.  
It is important than when you perform these level checks that you  
speak, sing or play at the level at which you will actually be recording.  
Most people, when they first start recording, tend to be a little louder  
than when they are simply checking the levels.  
5) While talking into the microphone, turn the INPUT 1TRIM  
control clockwise until the left 0 indicator is lit most of the  
time, and the +6 indicator is lit on the loudest parts.  
If the 0 indicator hardly lights at all, you may be too far from the  
microphone, or you are speaking too softly. If the microphone uses  
batteries, you may need to replace them.  
You can also bring the fader up from the 7-8 position to increase the  
level, but you should do this only after the TRIM control has been  
turned fully clockwise.  
6) Adjust the PHONES LEVEL until you are comfortable with  
what you hear in the headphones.  
14  
 
 
3 Making your first recording  
3.4 Recording the first track  
1) Set the REC FUNCTION switch of INPUT 1 to 1.  
You are now ready to record on track 1. Make sure the REC FUNC-  
TION switch of INPUT 2 is set to SAFE, so you don’t record on it by  
accident.  
2) Press the RECORD key (which will also press the PLAY key)  
and start recording the first spoken track.  
If the level as shown by the meters now seems a little high, you can  
“back off” on the fader a little.  
3) When you have finished (try to keep speaking for at least a  
minute), press the STOP key.  
4) Rewind the tape to the 000 mark.  
5) Start playing the tape, and adjust the LEVEL and PAN  
controls of track 1 so that you can hear clearly what you  
have just recorded.  
Note that meter 2 now shows the level of the tape replay on the right  
LINE OUT, rather than what is being input to the tape.  
NOTE  
You may notice a difference between the sound you hear when you replay the  
tape and the sound you hear when you are recording. This is perfectly nor-  
mal, and is due to the way that the Porta02 lets you hear previously-recorded  
material.  
6) Rewind and replay the tape again, listening carefully to  
your recording.  
7) Rewind and re-record the track as many times as you think  
necessary.  
Of course, this is only a test, so it doesn’t matter too much, but when  
you’re making a real recording, it’s important to make the recording  
as good as possible.  
8) When you’re happy with the recording, set the REC  
FUNCTION switch of INPUT 1 to SAFE.  
If you replay now, both meters will now show off-tape monitoring  
15  
 
3 Making your first recording  
3.5 Recording the next track  
Since you plugged the microphone into MIC/LINE 1 / MONO, and  
didn’t plug anything into MIC/LINE 2, the microphone signal is split  
as if it was plugged into both channels.  
1) Take fader 1 to the 0 mark.  
2) Set the level for input channel 2 in the same way as you set it  
for input channel 1 (see 3.3, “Setting the level”).  
3) Set REC FUNCTION switch for INPUT 2 to 2.  
You are now ready to record on track 2.  
4) Rehearse your second spoken part by playing back the first  
track (adjusting the level and pan if necessary) while  
speaking the words for the second track.  
5) Rewind and record when you are ready.  
When you are recording, the meter of INPUT 2 will show the input  
levels of input 2. Since the signal is now going to track 2, the meter  
for input 1 will not show anything.  
6) Rewind and playback when you have recorded. Adjust the  
level and pan position of the two tracks with the LEVEL and  
PAN controls for tracks 1 and 2.  
Remember that the fader adjusts the level of what goes onto tape, not  
the replay levels.  
When you are playing back, the meter of INPUT 1 will show the level  
of the signal from the left outputs, and the meter of INPUT 2 will  
show the input signal level as long as the REC FUNCTION switch is  
not SAFE.  
7) Rewind and repeat the recording of track 2 until you are  
satisfied with it.  
SAFE input channel 2, and take both faders down to 0. Set  
the TRIM controls of both inputs to LINE.  
16  
 
3 Making your first recording  
3.6 Recording the stereo backing  
Now that tracks 1 and 2 are filled with spoken words, we’ll put  
some backing music behind them. We’ll assume that you’re using a  
CD player here (of course, it may be an MD player or a cassette  
player).  
NOTE  
This is a test recording and will not be used except as a test. However, if you  
are making recordings for public performance or distribution which include  
pre-recorded copyright material, you should be aware of the regulations con-  
cerning copyright in the area where you live. Unauthorized recording of copy-  
right material may be illegal.  
1) Make sure the volume on the amplifier is turned all the way  
down (it should already be turned down).  
2) Take off the headphones and unplug the microphone.  
3) Connect the left and right LINE OUT of the CD player to MIC/  
LINE inputs 1 and 2 of the Porta03.  
4) Set the REC FUNCTION switches of INPUTs 1 and 2 to 3 and 4.  
You are now ready to start recording on tracks 3 and 4.  
5) Start playing the CD track you will be recording. Adjust the  
faders so that the +6 meter indicators light on the loudest  
parts of the CD.  
6) Slowly turn up the amplifier volume so that you are  
listening at a comfortable level.  
7) Make the CD ready to play, and make sure that the Porta02  
is rewound to the start of the recording.  
8) Start recording, and start replaying the CD.  
9) When you come to the end of the CD material, stop the CD  
and Porta02, and rewind the Porta02 tape to the beginning  
of the recording.  
17  
 
3 Making your first recording  
3.7 Mixdown  
Make sure that your mastering recorder is connected to the monitor-  
ing system.  
1) Set both REC FUNCTION switches to SAFE, and move both  
faders down to 0.  
This will stop any extra unwanted noise from the inputs appearing in  
the final mix.  
2) Make sure the mastering recorder is ready to record, and  
put it into record pause mode. Do not start recording yet.  
If you are using a tape for mastering, make sure that you are not  
recording over anything you want to keep. If you are using a new tape,  
make sure that you have taken the tape past the leader portion. Make  
the noise reduction, etc. settings on the mastering recorder, which will  
give you the best sound quality.  
3) Play back the recording on the Porta02 and adjust the  
OUTPUT LEVEL and PAN controls on the Porta02.  
The nominal position (the best position) for the LEVEL controls is  
about the 2 to 3 o’clock position. This is the position you should  
regard as normal.  
It is usual to put the PAN controls for a stereo source such as a CD  
fully right and fully left.You can place the two voices anywhere in the  
stereo picture.  
Practice adjusting the levels of tracks 3 and 4 together to fade the  
backing music in and out.  
4) While adjusting the levels on the Porta02, watch the  
recording levels on the mastering recorder. If they are too  
high, take down the recording level on the mastering  
recorder.  
Remember that if you are recording on a digital recorder, such as an  
MD recorder, if the signal levels are too high, the result will be  
extremely unpleasant distortion. Analog recorders, such as cassette  
decks, will also distort if the levels are too high, but the distortion is  
much more pleasant (even so, you should try to avoid distortion in the  
mixdown).  
5) When you are happy with the mix rehearsal, rewind to the  
start of the recording on the Porta02.  
6) Start recording on the mastering machine, and start  
playback on the Porta02.  
18  
 
3 Making your first recording  
7) Mix the tracks, fading the backing music on tracks 3 and 4  
to taste.  
8) At the end, stop both machines. Rewind the mastering  
recorder.  
9) Set the amplifier input source to the mastering recorder,  
and replay your mix.  
10) If you are not happy with the mix, you can do it again,  
either recording over the old mix, or adding the new mix  
after the old one.  
Congratulations! You have now completed your first recording  
project with the Porta02. Rewind the Porta02 tape to the start,  
remove it, and clean the Porta02’s heads.  
19  
 
4 Hints and advanced tips  
4 – Hints and advanced tips  
This section gives a few hints and tips  
which may be useful to you when you  
make recordings using the Porta02.  
4.1 Recording techniques  
Learning how to record is an art, not a you, and there are several good books on  
science. One of the best teachers is expe- the subject which can explain the theory  
rience. However, there are a few things of recording and some of the techniques.  
mentioned here which may be useful to  
4.1.1 Recording electric guitars  
Much of the sound of an electric guitar  
(and also bass) is due to the effects,  
amplifier and speakers, as well as the gui-  
tar and style of playing. If you plug the  
guitar straight into the Porta02, you will,  
of course, be able to record it, but the  
sound will probably not be what you are  
used to.  
4.1.2 Recording with effects  
Professional recordings often use effects  
like digital reverberation on vocals, etc.  
You can add some of these effects by  
plugging the microphone into an effects  
unit, and plugging the unit into the  
Porta02. Note that the effects unit must  
be able to accept microphone-level sig-  
nals, and will output to the Porta02 at  
LINE levels.  
Plugging effects units between the guitar  
and the Porta02 will certainly help to pro-  
duce a fuller sound. The sound which  
will come closest to a live sound, though,  
will be provided by the amplifier itself.  
In addition, you will need to use the inter-  
nal balance control in the unit to decide  
how much of the “dry” (un-effected)  
sound will be passed through to the  
Porta02 for recording.  
You can adopt one of two approaches:  
either to put a microphone in front of the  
guitar speaker and record this (at MIC  
level), or to connect the output of the pre-  
.amplifier to the Porta02 and record at  
LINE level.  
If you do not have access to a reverbera-  
tion unit, you can try recording vocals in  
a very “live” room (without much furni-  
ture).  
WARNING  
Do not connect the speaker output (or head-  
phone output, if provided) of the amplifier to  
the Porta02. This will almost certainly dam-  
age the Porta02, and may damage the ampli-  
fier. Only use outputs which are marked  
LINE OUT, PRE OUT, DIRECT OUT  
and so on. Avoid using any outputs marked  
SPEAKER OUT, SP OUT, 4, 8, 16Ω  
or the like.  
20  
 
4 Hints and advanced tips  
4.1.3 Metering  
In general, you should not try to record at When playing back if one or both of the  
too high a level, and the +6 indicator input channels has set to SAFE, they will  
should not be lit more than half the time display the levels of the signal sent to the  
(at the very most).  
left LINE OUT (channel and meter 1) or  
the right LINE OUT (channel and meter  
2). If a signal is also received at the MIC/  
LINE input jacks, this will be added to the  
playback for metering.  
The meters display the input levels to the  
channels at all times except when playing  
back with the input channels in SAFE  
mode.  
4.1.4 When you’re not recording  
Try to get into the habit of always leaving recording by accident (remember that  
the REC FUNCTION switches in the SAFE pressing RECORD with both channels  
position unless you are actually recording SAFE is the same as pressing PLAY).  
or rehearsing a take. This will stop you  
4.2 Mixdown  
What sounds good is something that tant pieces of equipment that you have  
depends on personal taste, but most pro- are your ears! Train yourself to use them  
fessionals try to avoid mixes with too so that you can spot mistakes quickly,  
much bass or high end (unless it’s for a and you know how to put them right, just  
special effect). However, the most impor- by listening. It’s a useful skill!  
4.2.1 Recording more than four tracks (i)  
Although the Porta02 has only 4 tracks, it 2) Set both REC FUNCTION switches to  
is possible to produce a mix with more  
than four sounds. Here’s one way, which  
involves adding one or two more extra  
inputs to the four recorded tape tracks.  
SAFE.  
3) Connect the source for the extra  
inputs to the MIC/LINE jacks and  
adjust the TRIM controls to match  
the level.  
These extra inputs will be panned either  
fully left or right (or one track will be in  
the center) and the mix proceeds as the  
extra inputs are recorded. This method is  
therefore useful for adding a pre-recorded  
stereo backing to go behind the four  
recorded tracks.  
4) Play back the tape, and use the  
OUTPUT LEVEL and PAN controls to  
adjust the playback of the tape  
tracks.  
5) Use the faders to adjust the levels  
of the input signals against the tape  
tracks.  
1) Record on all four tracks of the  
Porta02.  
4.2.2 Recording more than 4 tracks (ii)  
For this method, there must be an ordi- The four tracks of the Porta02 are mixed  
nary stereo cassette recorder used as the in the usual way onto a stereo cassette.  
mastering recorder.  
This cassette is then removed from the  
mastering recorder and replaces the 4-  
21  
 
5 Troubleshooting  
track tape in the Porta02. The left and  
right stereo tracks of the mastering  
recorder can be used as tracks 1 and 2 of  
the Porta02, leaving tracks 3 and 4 ready  
for recording.  
ing the Porta02 tracks to the mastering  
machine, as the Porta02 does not use  
noise reduction. Of course, on the  
final stereo mix, you can use noise  
reduction on the mastering machine.  
Once you have mixed the four tracks  
to two, you cannot adjust their levels  
or pan positions again on the new  
tape. Think ahead to what tracks you  
will record on the new tape, and mix  
accordingly.  
There are a few points to remember:  
Although you can repeat this process  
of mixing 4 tracks to 2 and then add-  
ing 2 more, as you repeat the mix pro-  
cess, noise and hiss will build up to a  
point where the quality becomes unac-  
ceptable.  
When using this technique, always use  
the same type of tape in the Porta02  
and mastering machine. Differences in  
tape type may affect the sound.  
The mastering recorder must have its  
noise reduction turned off when mix-  
5 – Troubleshooting  
Tracing faults in a recording setup is which hasn’t been plugged in properly, or  
often a mixture of logical deduction and a faulty cable. If you discover a faulty  
patience. Very often, the problem is cable, replace it with a new one–it’s not  
caused by something simple; a cable worth hanging onto bad cables!  
Is the PS-P2 adaptor plugged into the power supply?  
The Porta02’s POWER light does  
Is the PS-P2 adaptor plugged into the Porta02?  
not come on  
Is the switch on the Porta02 set to ON?  
Is the tape properly inserted in the Porta02?  
Is the tape at the end of the tape?  
The tape does not move when  
PLAY is pressed  
If you’ve just put in a tape you recorded in another session, make  
sure that it’s the right way round.  
Make sure the OUTPUT LEVEL controls are set to monitor the  
tape tracks (not at 0). Set the REC FUNCTION switches to  
SAFE and look at the meters.  
Some tracks have been recorded  
on the tape, but nothing can be  
heard when playing back  
Try monitoring through headphones and adjust the PHONES  
LEVEL. If you can hear something through the headphones, check  
the LINE OUT connections.  
Make sure the amplifier is set to the correct input source.  
Is the source (microphone, guitar, etc.) switched on and volume  
control turned up? If it uses batteries, does it need new batteries?  
Nothing appears on the meter  
indicators when a source is  
played  
Is theTRIM control of the channel set correctly?  
Is the tape properly inserted in the Porta02?  
Is the tape record-protected?  
Cannot press the RECORD key  
Is the REC FUNCTION set to SAFE?  
Check the OUTPUT LEVEL control for the track.  
The RECORD key is pressed, the  
tape moves, but nothing is  
recorded, or the level is very low  
Is theTRIM level set correctly (a microphone feeding a channel set  
to LINE will sound very faint).  
22  
 
6 Specifications  
If you’re listening through headphones, is the Porta02’s MONO  
switch pressed?  
The PAN controls don’t work  
If you’re listening through speakers, is there a MONO switch on  
the amplifier which has been pressed?  
When monitoring while recording, the sound will often be a little  
different to when it is played back. A large amount of distortion  
may be caused by recording at too high a level (shown by the meter  
+6 indicator being lit all or most of the time). Adjust theTRIM  
level and/or back off on the faders.  
Recorded sound is distorted  
when recording  
If the meter +6 indicator is not constantly lit, you may want to  
reduce the headphone level; you may be driving the headphones  
too hard.  
level of all four tracks is too high. Try reducing the level of all  
tracks so that the meter +6 indicator is not constantly lit on play-  
torted, it was recorded at too high a level.  
Recorded sound distorts on  
playback.  
The heads are dirty. Clean them (see 1.2.4, “Cleaning the heads”)  
Tape sounds muffled on play-  
back  
The capstan and pinch roller are dirty. Clean the capstan and pinch  
roller (see 1.2.5, “Cleaning the pinch roller”).  
Pitch changes (wow and flutter)  
You’re probably listening to tracks 1 and 2 forwards at the same  
time as 3 and 4 backwards. Turn down the OUTPUT LEVEL con-  
trols of tracks 3 and 4.  
A stereo tape recorded on  
another machine sounds really  
strange!  
If the sound is unnaturally “bright”, it’s quite likely that the tape  
was recorded on the other machine using noise reduction.  
6 – Specifications  
Compact cassette tape, CrO (Type II, 70µs EQ), C-30 to  
Recommended tape type  
2
C-90  
4 tracks, 4 channels  
Track format  
1 x 4-track record/replay head (Permaloy)  
1 x 4-track erase head (ferrite)  
1 x DC motor (capstan and reel motor)  
1 7/8 in./sec (4.76 cm/sec)  
0.18%  
Head configuration  
Motor type  
Tape speed  
Wow and flutter  
Fast wind speed  
Power requirements  
Approx 120 seconds (C-60 tape)  
USA/CANADA: 120V AC, 60Hz  
U.K./EUROPE: 230V AC, 50Hz  
AUSTRALIA:  
240V AC, 50Hz  
7W, via the supplied PS-P2 AC adaptor  
Power consumption  
305 x 64 x 205 (mm), 12.0 x 2.5 x 8.1 (in.), maximum  
height (including controls) 80 (mm), 3.1(in)  
Physical dimensions (w x h x d)  
1.5kg (3.3lb)  
Weight (main unit)  
MIC/LINE inputs (2 x 1/4" jacks)  
Input level  
–50dBV, TRIM at maximum; –10dBV, TRIM at minimum  
50kΩ  
Input impedance  
23  
 
6 Specifications  
LINE outputs (2 x RCA jacks)  
Output level  
–10dBV  
10kΩ  
Output impedance  
Headphone output (1/4" stereo  
jack)  
60mW + 60mW  
Output level  
Output impedance  
Frequency response  
Signal-to-noise ratio  
Total Harmonic Distortion  
Channel separation  
Erasure  
30Ω  
50Hz – 12.5kHz ±3dB  
43dB  
Better than 3.0% (400Hz, –10dB)  
Better than 40dB (at 1kHz)  
65dB (at 1kHz)  
0 dBV is referenced to 1 volt  
Changes in features or specifications may be made without notice or obligation.  
305mm  
TEAC CORPORATION  
3-7-3, Nakacho, Musashino-shi, Tokyo 180, Japan Phone: (0422) 52-5082  
TEAC AMERICA, INC.  
7733 Telegraph Road, Montebello, California 90640 Phone: (213) 726-0303  
TEAC CANADA LTD.  
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada Phone: 905-890-8008 Facsimile: 905-890-9888  
Privada De Corina, No.18, Colonia Del Carmen Coyoacon, Mexico DF 04100 Phone: 5-658-1943  
5 Marlin House, Marlins Meadow, The Croxley Centre, Watford, Herts. WD1 8YA, U.K. Phone: 01923-819699  
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany Phone: 0611-71580  
TEAC MEXICO, S.A. De C.V  
TEAC UK LIMITED  
TEAC DEUTSCHLAND GmbH  
TEAC FRANCE S. A.  
17 Rue Alexis-de-Tocqueville, CE 005 92182 Antony Cedex, France Phone: (01) 42.37.01.02  
P.A. TEAC Nederland BV, Perkinsbaan 11a, 3439 ND Nieuwegein, Netherlands Phone: 0031-30-6048115  
Perkinsbaan 11a, 3439 ND Nieuwegein, Netherlands Phone: 030-6030229  
TEAC BELGIUM NV/SA  
TEAC NEDERLAND BV  
TEAC AUSTRALIA PTY., LTD.  
A.C.N. 005 408 462  
106 Bay Street, Port Melbourne, Victoria 3207, Australia Phone: (03) 9644-2442  
Via C. Cantù 5, 20092 Cinisello Balsamo, Milano, Italy Phone: 02-6601050  
TEACITALIANA S.p.A.  
PRINTED IN TAIWAN 1097 M-1349A  
 

Therma Stor Products Group Ventilation Hood Quiet Vent Ventilation System User Manual
TOA Electronics Security Camera C CV854D 3 CE User Manual
Topcom Blood Pressure Monitor BPM ARM 3301 User Manual
Toro Lawn Mower 51465230000001 Up User Manual
Toshiba Printer B 480 QP SERIES User Manual
TRENDnet Bluetooth Headset BlueSoleil User Manual
Unimac Washer M30 CONTROL User Manual
Vision Fitness Home Gym 2200 HRC User Manual
Vivitar Camcorder F332 User Manual
Wagner SprayTech Paint Sprayer W 867 E User Manual