Tasco Digital Camera 119203C User Manual

Digital Trail Camera  
Instruction Manual  
Model#: 119203C  
LIT #: 98-1164/03-10  
 
QUICK GUIDE: TASCO TRAIL CAMERA  
1. Open the camera by releasing the latches on the right side of the camera. Install 4Dcell batteries (flat base of all batteries  
contacting springs), and insert an SD card (not included, use any capacity up to 2GB) in the slot to the right of the 5 buttons  
(upside down, brand name facing you). Press the card down until you hear it click into place.  
2. Press and release the Power switch. If you are using the camera for the first time, you should set the date and time so your  
photos will be “stamped” correctly. Briefly press the Menu button-the “year” digits will blink on the display. Use the Up/Down  
buttons to set the current year, then press Enter, and repeat to set the month and press Enter again. The display will then  
change to let you set the date. After setting the date, press enter, and set the time (thehourdigits will flash, use Up/Down to  
set the hour and then minute. The time display uses the 24 hr standard, so 2:00 PM is indicated as “1400, etc).  
3. After the date and time have been set, and Enter is pressed, you have a choice of three operating modes: Still photos with  
“Lo” resolution (this is the default setting if you don’t change it), Still photos with “Hi” resolution, or movie (video) mode. To  
change modes, press Up or Down to cycle through the choices (each will blink), pressing Enter to set the mode you prefer.  
4. In normal operating mode, the display will only show the still photo or movie clip icon in the lower left corner, an SD card  
icon on the lower right, and one or more digits that indicate how many photo or movie files have been stored on the card. To  
test the camera operation, wave your hand in front of the lens and PIR (passive infrared/motion) detector, while looking at  
the LCD display. As long as events are being detected, a new still photo or movie clip (as set in previous step) will be recorded  
every 30 seconds, indicated on the display by “SnAP, then “SLP. Note: for movie clips, the display will stay on “SnAP” for the 15  
sec duration of each movie.  
5. Thread the strap through the slots on the back of the Trail Cam and attach the buckles, then strap it onto a suitable tree,  
making sure the strap is tight and the camera is aimed at the area you wish to observe. Turn on the camera (make sure a new  
or empty SD card has been inserted) and leave the area-there is a 60 second delay after power on before the first photo is  
taken. Alkaline batteries typically last 30 days or more, depending on how often the Trail Cam is activated, how often the flash  
fires, ambient temperature, etc.  
6. To look at your captured photos, make sure the power is off, and remove the SD card by pushing down lightly on the top  
edge of the card-it will pop up for removal. Use an SD card reader with any PC or Mac to view, copy, or delete the photos  
(standard JPG files) and movies (AVI files) inside the “DCIM/100MEDIAfolder on the card. Double click on an individual file  
to see it, or open the files with the photo software of your choice.  
 
3
Digital Trail Cam Specifications  
Lens  
F/3.5, effective focal length 42mm. Sight range: 45 degrees  
Flash  
High power electronic Xenon Flash. Range: 30 ft.  
PIR Sensor  
Low noise, high sensitivity passive infrared sensor. Range: 30 ft.  
Motion LED Indicator Yes  
Display  
Monochrome LCD. Auto-off: 3 min. 2-digit event and image display.  
File Format  
Standard JPEG format (.jpg) still photos. Video movie clips (.avi). DCF ver. 1.0 file  
management.  
Photo Modes  
1.3MP or 3MP* still photo, or AVI video (320x240 pixels per frame, 10 frames per  
second rate, 14 second length)  
Exposure  
Auto  
White Balance  
Power Supply  
Battery Life  
Auto  
4 x “Dsize alkaline batteries  
Alkaline batteries: Approximately 90 days (dependant on temperature, camera  
activity and flash usage).  
Card Compatibility  
Up to 8 GB maximum capacity secure digital (SD)cards. The use of MMC cards is  
not recommended.  
* High resolution photos processed via software interpolation before storage  
 
4
Glossary  
PIR—Passive Infrared Sensor. Senses motion like typical security motion detector. Requires infrared energy  
(heat) in addition to motion to trip sensor to assure detection of live animals.  
Image—A digital picture recorded on the SD Card when motion is sensed. Images are taken at the desired  
delay between images.  
Image Delay—Time elapsed between photos while events are sensed and recorded. This is fixed at 30 second  
intervals in the Trail Cam.  
Camera Flash—Xenon Flash used for low light photography. Automatically fires if required.  
SD Card—Memory card used to store images and events. Compatible with up to 8GB capacity SD card.  
Battery Life—Time that camera will function in the field. Dependent on temperature, number of images and  
number of flashes during that time.  
Setup—Using the display menu and buttons to set the date/time, and still photo or movies option.  
Trigger Speed—Time delay between a subject passing in front of PIR sensor and the image capture of that  
subject. All Tasco Trail Cameras have a trigger speed of less than one second.  
 
5
Front of Camera  
Control Panel  
Inside Front  
PIR  
Flash  
LCD  
Display  
Camera  
Lens  
SD Card Slot  
Button & Display  
Detail  
Setup,  
Menu &  
Power  
PIR Detected (or  
Low Battery) LED  
Buttons  
Lock  
Tab  
Parts  
Guide  
 
6
Setup and Operation Guide  
1. Open the Cam by pulling out on the two latches on the right side. Install 4 “D” cell batteries (flat base of all  
batteries contacting springs), and insert an SD card (not included, use any capacity from 16MB to 8GB. Do not  
substitute MMC cards.) in the slot to the right of the 5 buttons as indicated on the slot cover (upside down,  
with the notched corner of the card on the left and metal contacts of the card facing the back of the slot). Press  
the card down until you hear it click into place. If the Cam is turned on without a card in place, it may not turn  
off-reset it by pulling one of the batteries out partway, insert a new or empty SD card, and put the battery back  
in place. Only remove or insert cards with power off.  
2. If you are using the camera for the first time, you should set the date and time so your photos will be  
“stamped” correctly. Briefly press the Menu button-the first two digits of the  
year will flash, prompting you to enter the year (a). Use the Up/Down buttons  
to set the current year, then press ENTER. Set the month the same way, and  
press ENTER again. The display will then change to let you set the day, with  
a
only the last two digits blinking (b). Again use the Up/Down buttons to  
change the day if necessary and press ENTER. To set the time, use Up/Down to  
set the hour and minute. The time display uses the 24 hr standard, so 2:00 PM  
is indicated as “1400, etc.  
b
3. After the date and time have been set, press ENTER. Then the camera  
icon will and the word “Lo” will blink (c). By pressing UP/DOWN, the camera  
will cycle between Lo resolution still photo, Hi resolution still photo, and  
movie (video) modes. Choose the mode that you want and press ENTER. The  
c
“Lo” setting will allow you to take lower resolution images and therefore  
accumulate more images on your card while theHIsetting will give you high  
 
7
Setup Guide (cont.)  
resolution images of better quality but fewer images can be stored to the card. In Movie mode a 14 second AVI  
file will be recorded to the SD Card each time the camera is triggered.  
4. Pressing ENTER again after the resolution options will go to the Format screen next. Formatting is  
recommended before you re-use an old SD card, and is a quick way to erase all of the photos/videos after  
you’ve saved any you wish to keep. The display will readFoNo, withNoand  
the SD card icon blinking (d). Press ENTER when “No” is flashing if you don’t  
want to format the card. To format the card, press either UP/DOWN button  
and the “Fo” portion will blink. Press ENTER and the display will change to “Y  
d
N” with the SD card icon blinking. “N” (NO) is the default, so pressing ENTER  
will cancel the formatting, then pressing and holding MENU will exit menu  
mode. If you are certain that you want to format the card and DELETE all data and images on the card,  
then press either UP/DOWN button to select “Y” (YES). With “Y” flashing, press ENTER- the display will briefly  
change toSdFr. After the card has been formatted, the camera will exit the MENU mode and is ready to take  
images.  
5. Press and hold MENU to exit Menu mode at any time once you have finished changing any of the menu  
item settings or using one of the menu options.  
6. In normal operating mode, the display will only show the still photo or movie clip icon in the lower left  
corner, an SD card icon on the lower right, and one or more digits that indicate how many photo or movie  
files have been stored on the card. To test the camera operation, wave your hand in front of the lens and PIR  
(passive infrared/motion) detector, while looking at the LCD display. As long as events are being detected, a  
new still photo or movie clip (as set in the menu) will be recorded every 30 seconds, indicated on the display  
 
8
Setup Guide (cont.)  
by “SnAP, then “SLP” (Sleep). Note: for movie clips, the display will stay on “SnAP” for the 14 sec duration of each  
movie.  
7. Thread the strap through the slots on the back of the Cam and attach the buckles, then strap it onto a  
suitable tree, making sure the strap is tight and the camera is aimed at the area you wish to observe. The  
red LED lamp on the front of the camera can help you determine how large an area is covered, as it will flash  
when an “event” is detected. Turn on the camera (make sure a new or empty SD card has been inserted) and  
leave the area-there is a 60 second delay after power on before the first photo is taken. Batteries typically last  
30 days or more, depending on how often the Cam is activated by events, how often the flash fires, ambient  
temperature, etc. The red LED lamp will stay on continually to indicate a low battery condition.  
8. To view your captured photos, make sure the power is off, and remove the SD card by pushing down lightly  
on the top edge of the card-it will pop up for removal. Insert it into an SD card reader (available at most  
computer, photo, or electronics dealers) connected via USB to your PC or Mac to view, copy, or delete the  
photos (standard JPG files) and movies (AVI files) inside theDCIM/100MEDIAfolder on the card. Double click  
on an individual file to see it, or open the files using the photo software of your choice.  
 
9
Additional Notes  
MOON PHASE STAMP  
All new Trail Cam models have amoon phasestamp feature. This links the current date (as set by the user in  
the setup procedure) to the phase of the moon on that date (this data is stored on an internal memory chip),  
and imprints a icon on your photo which represents the moon phase when the photo was taken. The moon  
phase icon will appear on your photos in the lower left, next to the Tasco logo. Some hunters will find this to  
be a useful reference, as it can help determine if particular animals are inactive at night when a full or nearly  
full moon is present, causing them to be more visible to predators. Or, if some of your night photos seem to  
have a darker or lighter background (beyond the range of the flash), you can see if that was related to how  
bright the moon was at the time. The icons for the various phases of the moon are shown below:  
Waxing >  
Waning >  
New  
New  
Full  
ABOUT THE PIR SENSOR  
The sensor that triggers the trail camera is Passive Infra Red, or PIR. Infrared energy is essentially heat energy.  
The PIR detector operates by sensing a change in the infrared level in its detection zone. This zone is a cone  
in the center 30 degrees of the camera’s field of view. The camera establishes an average long-term infrared  
level. When this level increased suddenly the PIR detector signals the camera to record a picture and/or an  
event. Because of this effect, the PIR detector will be more sensitive at night, when the average temperature  
is lower.  
You can use the red LED indicator on the front of the camera to confirm the detection zone.When PIR is  
sensed, this “PIR detected” indicator will light. The camera’s field of view is a 45 degree cone, centered on the  
PIR detection zone.  
 
10  
FCC Note:  
ONE YEAR LIMITED WARRANTY  
This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However,  
there is no guarantee that interference will not occur  
Congratulations on the purchase of your new Tasco product. You have chosen one  
of the finest values available today. This product carries Tasco’s ONE YEAR LIMITED  
WARRANTY. This product is warranted against original defects in material and/or  
workmanship for the length of time specified by this warranty, provided, however,  
that the unit has not been abused, taken apart or tampered with in any way  
whatsoever.  
This warranty is limited to the original purchaser and is not transferable. This warranty  
applies only to products purchased in the United States of America. Any return  
made under this warranty must be accompanied by the items listed below:  
1) A check/money order in the amount of $10.00 to cover the cost of  
postage and handling  
in  
a
particular installation. If this equipment does  
cause harmful interference to radio or television  
reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the  
following measures:  
2) Name and address for product return  
3) An explanation of the defect  
4) Proof of Date Purchased  
5) Product should be well packed in a sturdy outside shipping carton to  
prevent damage in transit, with return postage prepaid to the address  
listed below:  
· Reorient or relocate the receiving antenna.  
·
Increase the separation between the equipment and  
receiver  
.
· Connect the equipment into an outlet on a circuit  
different from that to which the receiver is  
connected.  
· Consult the dealer or an experienced radio/TV  
technician for help.  
SEND TO:  
TASCO  
Attn.: Repairs  
8500 Marshall Drive  
Lenexa, Kansas 66214  
Shielded interface cable must be used with the  
equipment in order to comply with the limits for a  
digital device pursuant to Subpart B of Part 15 of FCC  
Rules.  
Tasco shall not be liable for any consequential, incidental or contingent damages  
whatsoever. Some states do not allow the exclusion of incidental or consequential  
damages, so the above limitation or exclusion may not apply to you. This warranty  
gives you specific legal rights, and you may have other rights which vary from state  
to state.  
Specifications and designs are subject to change  
without any notice or obligation on the part of the  
manufacturer.  
Non-warranty repairs or refurbishing of your Tasco product are always provided at a  
reasonable cost. For products purchased outside the United States please contact  
your local dealer for applicable warranty information.  
©2010 B.O.P Tasco, TM, ®, denote trademarks of B.O.P  
 
For further questions or additional information please contact:  
Tasco  
9200 Cody, Overland Park, Kansas 66214  
(800) 423-3537 • www.tasco.com  
©2010 B.O.P.  
 

Tascam CD Player CD R624M User Manual
Tiger Lawn Mower JD 5083E User Manual
Timex Clock Radio T617 User Manual
TMC Telephone EV4500 User Manual
Transcend Information Computer Hardware TS2G 8GCF266 User Manual
Transition Networks Network Card CPSMM 120 User Manual
Venture Products Car Amplifier VP100L User Manual
Vision Fitness Speaker System ST730 User Manual
VTech Baby Toy 91 002761 001 User Manual
Wachsmuth Krogmann CRT Television TQ 10 User Manual