Teac Stereo System CD RW880 User Manual

Z
CD-RW880  
Quick-Start Recording Guide  
This Guide provides you with the simplest way to use this equipment for recording.  
Of course, we strongly suggest that you consult the Owner’s Manual for complete details and important safety information.  
Connections  
This is the simplest connection to enjoy CD recording.  
1
Connect the CD-RW880 to your Amplifier, for listening to CD-Rs and  
CD-RWs, and for checking recording.  
Make sure to connect:  
white plug q white jack (L: left channel)  
red plug q red jack (R: right channel)  
2
3
Connect the CD-RW880 to your CD Player or MD Deck using an  
optical digital cable.  
When using the DIGITAL IN terminal, remove the cap from the terminal.  
R
L
R
L
DIGITAL OUT  
REC PLAY  
AC Outlet  
Finally, connect the power cord.  
CD Player, MD Deck, etc.  
Amplifier  
Recording  
When the POWER button is pressed, the unit returns to the factory settings.  
About CD-R/CD-RW discs  
You must use CD-R and CD-RW discs bearing the  
“DIGITAL AUDIO” logo. This unit CANNOT RECORD CD-  
R and CD-RW discs designed for computer systems.  
1
As this guide is based on the factory settings, be sure to start from step  
.
Manual track division  
5
4
Play the source to be recorded.  
Press the RECORD button.  
It is possible to divide the recording into tracks while  
recording.  
The unit will start synchronous recording.  
The unit enters record pause mode.  
While the recording is taking place, press the TRACK  
INCREMENT button. The current track number will be  
incremented by one.  
< During digital synchronous recording, if  
the input signal stops for 5 seconds,  
recording will stop automatically.  
< Press the STOP button to stop the  
recording manually.  
Finalizing  
Although audio data may be written on a CD-R or CD-  
RW disc, a standard CD player will not be able to play  
back the audio until a final table of contents (TOC) has  
been written at the start of the disc.  
The process of writing this table of contents is known as  
“finalizing”. Once this has been done, no further data  
can be written to the disk.  
1
Press the FINALIZE button in the stop mode.  
“FINALIZE” appears on the display.  
2
Press the PLAY (y) button to start finalizing.  
1
2
3
Press the POWER switch.  
Load a recordable CD-R or CD-  
RW disc into the unit.  
Select “SYNC ALL” using  
the SYNC 1/ALL button.  
The unit enters standby  
mode, and “STAND-BY”  
lights on the display.  
Press the OPEN/CLOSE button (L),  
place a disc on the disc tray with the  
printed label side up, and then press  
the OPEN/CLOSE button (L) to close  
the disc tray.  
“TOC” and the “REC” indicator blink, and the  
remaining time for the finalizing operation appears  
in the display.  
When the operation has been finished, the display  
returns to the track/time display.  
< Pressing the OPEN/CLOSE button in  
the standby mode turns the unit on.  
< Although finalized CD-R discs may be played on  
most ordinary CD players, remember that some  
finalized CD-RW discs may not play on older CD  
players.  
.
TEAC CORPORATION 0705 MA-0992A  
9A10350200  
 

TeleType Company GPS Receiver Bluetooth GPS Receiver User Manual
Toastmaster Oven RST18 User Manual
Toastmaster Toaster T75BR User Manual
TP Link Network Card TL PA111 User Manual
Tricity Bendix Cooktop CSIE452 User Manual
Tripp Lite Switch PDUMH20NET2 User Manual
Tyan Computer Marine Sanitation System B5382 User Manual
Univex Blower 358799370 User Manual
Villaware Blender NDVLCB0100 User Manual
Vivitar Digital Camera S529 User Manual