Tech4o Watch Alti Ski User Manual

 
1.0  
Introduction/Features:  
Altimeter w/cumulative assent/descent  
Tech4o Alti-Ski Watch™  
Owner's Manual  
• Barometer  
Temperature  
Content:  
Introduction/Features  
• Ski Run Counter  
• Time / date / alarm  
11.3  
11.4  
11.5  
12.0  
12.1  
12.2  
12.3  
13.0  
To make the most of your purchase, be sure to carefully read this  
manual and follow the included flow chart. Keep them safe for  
future reference. Please follow these precautions in using and  
caring for your new Tech4o Alti-Ski Watch:  
• Avoid exposing the watch to extreme conditions  
• Avoid rough use and/or severe impacts  
• Occasionally clean the watch with a soft and moistened cloth  
• Store the watch in a clean, dry place when not in use for an  
extended period of time.  
Ascent Mode - Max Rate of Ascent  
Ascent Mode - Total Daily Ascent  
Ascent Mode - Total Lifetime Ascent  
Run Counter - Display  
Run Counter - Trip Run Counter  
Run Counter - Daily Run Counter  
Run Counter - Lifetime Run Counter  
Limited Warranty  
2
3
 
 
TEMPERATURE  
1.1 Button Functions On/Off  
Mode Button: [M]  
Used to select among the main modes of the  
watch  
ALTIMIETER  
TIME  
Button: [o/o]  
Used to confirm selections, start/stop the  
stopwatch, and lock/unlock altitude  
Set/+ Button: [s/+]  
RUN  
DESCENT  
Used to access setting mode and increase/  
change digits during setting display. Also sets  
intermediate/lap times in stopwatch mode  
ASCENT  
Option/- Button: [o/-]  
Used to decrease/change digits during setting display and browse  
through sub-functions  
2.0 Time / Date Mode - Display  
When Time / Date mode is selected, the  
watch will display the current time  
on the top row and the current date,  
temperature, or ski run counter on the  
bottom row.  
Light Button: [L]  
Used to illuminate the watch face for use during low light conditions  
To view time mode, press the [m] button  
until the mode indicator displays the  
clock symbol.  
1.2 Major Function Modes  
Press any button to wake the watch from sleep mode. Press the [M]  
button to toggle among the main function modes.  
4
5
 
 
2.1 Time / Date Mode - Setting  
3.0 Daily Alarm Mode - Display  
This watch includes a daily alarm. When the daily alarm is ON, the  
alarm will sound for 30 seconds at the  
alarm time every day.  
To view the daily alarm display, press  
the [o/-] button once while in time/date  
mode.  
In Time / Date mode press and hold the Set/+ button [s/+] for  
two seconds.  
The 12 H / 24 H will flash. Use the [o/-] button to select between  
a 12 or 24 hour clock feature. Press the [o/o] button to confirm  
selection.  
The hours will flash. Use the [s/+] and [o/-] buttons to select the  
correct hour. Press the [o/o] button to confirm selection.  
The minutes will flash. Use the [s/+] and [o/-] buttons to select  
the correct minutes. Press the [o/o] button to confirm selection.  
The month will flash. Use the [s/+] and [o/-] buttons to select the  
correct month. Press the [o/o] button to confirm selection.  
The days will flash. Use the [s/+] and [o/-] buttons to select the  
correct day. Press the [o/o] button to confirm selection.  
The year will flash. Use the [s/+] and [o/-] buttons to select the  
correct year. Press the [o/o] button to confirm selection.  
You have now completed the Date / Time Mode quick set.  
When the daily alarm is selected, the  
watch will display the alarm setting  
indicator in the top row and the daily  
alarm time in the bottom row.  
3.1 Daily Alarm Mode - Setting  
To set the daily alarm, press and hold the [s/+] button for 2  
seconds. The hours will flash.  
Use the [s/+] and [o/-] buttons to adjust the hours. Press the [o/o]  
button to confirm selection.  
At this time, the minutes will flash.  
Use the [s/+] and [o/-] buttons to adjust the minutes. Press the  
[o/o] button to confirm selection.  
Press the [o/o] button again to set the alarm for on or off.  
continues  
6
7
 
 
Press the [o/-] button to confirm selection and advance to the  
countdown timer mode.  
4.2 Countdown Timer Mode  
Using the Countdown Timer  
4.0 Countdown Timer Mode - Display  
When in countdown timer mode, press the [o/o] button to  
start the countdown.  
This watch includes a countdown timer.  
To view the countdown timer, press the  
[o/-] button twice while in time/date  
mode.  
• When the countdown timer is selected,  
the watch will display the countdown  
time in the top row and the current home  
time in the bottom row.  
Press the [o/o] button again to stop the countdown.  
Press the [o/o] button again to resume the countdown  
When the countdown timer expires the alarm will sound for  
30 seconds and the timer will reset to the last countdown  
timer setting.  
Press the [o/-] button to proceed to the Stopwatch Mode.  
5.0 Stopwatch Mode - Display  
4.1 Countdown Timer Mode - Setting  
This watch features 5 individual  
stopwatch counters.  
To set the countdown timer, press and hold the [s/+] button for 2  
seconds. The hours will flash.  
Use the [s/+] and [o/-] buttons to adjust the hours. Press the [o/o]  
button to confirm selection.  
At this time, the minutes will flash.  
Use the [s/+] and [o/-] buttons to adjust the minutes. Press the  
[o/o] button to confirm selection.  
Use the [s/+] and [o/-] buttons to adjust the seconds. Press the  
[o/o] button to confirm selection and finish.  
The measuring unit of the stopwatch  
is 1/100 seconds for the first 59  
minutes, 59.99 seconds. After  
reaching 1 hour of cumulative time,  
the measuring unit changes to 1  
second and the measuring range is 99  
hours, 59 minutes, 59 seconds  
continues  
8
9
 
 
Press the [o/o] button again to stop the stopwatch. The top and  
bottom rows will now display current stopwatch time.  
Press the [o/o] button again to resume the stopwatch. The top row  
will now display ------------- and the bottom row will display the  
current stopwatch time.  
To view the stopwatch, press the [o/-] button three times while in  
date/time mode.  
When the stopwatch is selected, the watch will display StP 1 in the  
top row and 0:00 in the bottom row.  
5.1 Stopwatch Mode - Setting  
While the stopwatch is running, you may enter LAP/INT times by  
pressing the [s/+] button. The top row will display the first LAP/  
INT time and the bottom row will display the cumulative stopwatch  
time.  
After each successive LAP/INT time is entered, the top row will  
display:  
In stopwatch mode, press and hold the [s/+] button for two  
seconds.  
The LAP/INT indicator will flash.  
Both LAP and intermediate settings will record time the same way,  
but the way the information is displayed will vary. The LAP setting  
will show the last lap time when the [s/+] or [o/o] buttons are  
pushed and in stopwatch history mode. The Intermediate setting  
will show the cumulative intermediate times when the [s/+] or  
[o/o] buttons are pushed and in stopwatch history mode.  
Use the [o/-] button to select between LAP and int settings. Press  
the [o/o] button to confirm selection.  
* the cumulative time of all the entered intermediate times  
if the int setting was selected; or  
* the last lap time if the lap setting was selected.  
The bottom row will display the cumulative stopwatch time.  
When the stopwatch is stopped, press the [o/-] button to proceed  
to the stopwatch history mode or press [s/+] to proceed to the  
next available stopwatch to begin recording another set of times  
following the steps above. Note: there are 5 available stopwatches.  
More stopwatch information can be recorded by clearing  
stopwatch data in the stopwatch history mode or by recording  
over stopwatch #5.  
5.2 Stopwatch Mode - Using the Stopwatch  
How to use the Stopwatch  
When in stopwatch mode, press the [o/o] button to start the  
stopwatch. The top row will now display ------------- and the  
bottom row will display the current stopwatch time.  
10  
11  
 
 
6.0 Stopwatch History Mode - Display  
7.0 Alternate Time Zone Mode - Display  
When the stopwatch history mode is  
selected the watch will display St HSt on  
the top row and the current home time  
on the bottom row depending on your  
selection made in temperature mode.  
To access the stopwatch history mode,  
press the [o/-] button 4 times while in  
time/date mode.  
When the alternate time zone mode is  
selected the watch will display TIME 2  
and the alternate time zone time in the  
top row and the home time mode in the  
bottom row.  
To view the alternate time zone display,  
press the [o/-] button 5 times while in  
time/date mode.  
6.1 Stopwatch History Mode - Navigating Data  
7.1 Alternate Time Zone Mode - Setting  
How to retrieve saved stopwatch information:  
In the alternate time zone mode, press and hold the Set/+ button  
[s/+] for two seconds.  
To view saved stopwatch information, press the [o/o] button in  
stopwatch history mode to view the desired history log  
Press the [o/-] button to confirm selection and view the desired  
data.  
Continue pressing the [o/-] button to scroll through the different  
LAP/INT times for that stopwatch log  
The hours will flash. Use the [s/+] and [o/-] buttons to select the  
correct hour, making sure to account for a.m. A, or p.m. P.  
Press the [o/o] button to confirm selection.  
The minutes will flash. Use the [s/+] and [o/-] buttons to select  
the correct minutes.  
Press [o/o] button at any time to view a different stopwatch log.  
To clear all saved stopwatch data, press and hold the [s/+] button  
while selecting a stopwatch log to view.  
Press the [o/o] button to confirm your selection.  
The alternate time zone is now set. Press the [o/-] to home time  
display.  
12  
13  
 
 
8.0 Temperature Mode - Display  
maximum temperature reading since the setting was last reset.  
Press the [o/-] button again to access the minimum temperature  
reading since the setting was last reset.  
Both maximum and minimum temperature readings can be reset by  
pressing and holding the [s/+] button for 2 seconds while viewing  
either the maximum or minimum records respectively.  
Surrounding temperatures are generally 10 - 15˚F / 5 - 8˚C  
cooler than watch readings due to the effects of the wearer's body  
temperature.  
To view temperature mode, press the [m]  
button until the mode indicator displays T.  
In temperature mode the watch will  
display temperatures in the top row and  
home time, temperature, or run counter  
in the bottom row.  
8.1 Temperature Mode - Setting  
For more accurate readings, remove the watch from your wrist and  
allow 5-10 minutes for sensors to adjust.  
In temperature mode, press and hold the  
[s/+] button for 2 seconds. The ˚F or ˚C indicator will flash.  
Press the [o/-] button to select between ˚F or ˚C.  
Press the [o/o] button to confirm selection.  
9.0 Altimeter Mode - Display  
In altitude mode the watch will display  
altitude and barometric measurements  
in the top row and the current home  
time, current temperature, or run counter  
depending our your personal selection.  
At this time the bottom row will flash.  
Press the [o/-] button to select between home time, temperature,  
or run counter to be displayed in the bottom row. Press the [o/o]  
button to confirm selection.  
8.2 Temperature Mode - Temperature Features  
To view Altimeter Mode, press the  
[m] button until the mode indicator  
displays A.  
Current, Maximum, and Minimum Temperatures:  
In temperature mode, press the [o/-] button to access the  
14  
15  
 
 
9.1 Altimeter Mode - Setting  
9.3 Altimeter Mode - Barometric Pressure  
In altimeter mode, press and hold the [s/+] button for 2 seconds.  
The current altitude reading will flash.  
In altimeter mode, press the [0/-] button to view the current  
barometric pressure.  
Using the [s/+] and [o/-] buttons, enter your reference altitude.  
Your reference altitude should be obtained from a reliable map  
source for your current altitude.  
To change the unit of measure, press and hold the [s/+] button for  
2 seconds.  
The inHG / mbar indicator will flash.  
Once you have researched and entered your reference altitude,  
press the [o/o] button to confirm selection.  
Use the [o/-] button to select your desired unit of measurement.  
Press the [o/o] button to confirm your selection.  
The ft/m indicator will now flash.  
Press the [o/-] button to select your desired unit of measurement.  
Press the [o/o] button to confirm selection.  
Altimeter mode also has an optional lock feature.  
Press the [o/o] button to lock altimeter mode and prevent any  
accidental recordings of changes in altitude.  
10.0 Descent Mode - Display  
In descent mode, the watch will display  
altitude descent measurements on the  
top row and the current home time,  
current temperature, or the run counter  
on the second row depending on your  
personal preference.  
9.2 Altimeter Mode - Maximum Altitude  
In altimeter mode, press the [o/-] button to view the maximum  
altitude.  
The maximum altitude is the highest altitude recorded since the  
feature was last reset.  
To view descent mode, press the [m]  
button until the mode indicator displays  
the down arrow.  
To reset the maximum altitude, press and hold the [s/+] button for  
2 seconds.  
16  
17  
 
 
10.1 Descent Mode - Trip Descent  
10.5 Descent Mode - Total Lifetime Descent  
In descent mode, the default view is the total trip descent view.  
To clear/reset the total trip descent, press and hold the [s/+]  
button for 2 seconds.  
In descent mode, press the [o/-] button 4 times to view the total  
lifetime descent.  
To clear/reset the total lifetime descent, press and hold the [s/+]  
button for 2 seconds.  
10.2 Descent Mode - Rate of Descent  
11.0 Ascent Mode - Display  
In descent mode, press the [o/-] button once to view the current  
rate of descent.  
To clear/reset the current rate of descent, press and hold the  
[s/+] button for 2 seconds. Note that the current rate of descent  
automatically recalculates every minute also.  
In ascent mode, the watch will display the  
total trip ascent on the top row and the  
current home time, current temperature,  
or the run counter on the second row  
depending on your personal preference.  
10.3 Descent Mode - Maximum Rate of Descent  
To view ascent mode, press the [m] button  
until the mode indicator displays the up  
arrow.  
In descent mode, press the [o/-] button twice to view the maximum  
rate of descent for the trip.  
To clear/reset the maximum rate of descent, press and hold the  
[s/+] button for 2 seconds.  
11.1 Ascent Mode - Trip Ascent  
In ascent mode, the default view is the total trip ascent view.  
To clear/reset the current rate of ascent, press and hold the [s/+]  
button for 2 seconds.  
10.4 Descent Mode - Total Daily Descent  
In descent mode, press the [o/-] button 3 times to view the total  
daily descent.  
The total daily descent is automatically reset at midnight.  
18  
19  
 
 
11.2 Ascent Mode - Rate of Ascent  
12.0 Run Counter - Display  
In ascent mode, press the [o/-] button once to view the current rate  
of ascent.  
To clear/reset the current rate of ascent, press and hold the [s/+]  
button for 2 seconds.  
To view the run counter press the [m]  
button until the mode indicator displays R.  
In run counter mode the watch will  
display run information in the top row  
and the current home time on the  
second row.  
A run is calculated based on altitude  
adjustment. An additional run is added  
to the total when a period of descent is  
followed by an ascent greater than 60ft.  
or 20m.  
11.3 Ascent Mode - Maximum Rate of Ascent  
In ascent mode, press the [o/-] button twice to view the maximum  
rate of ascent for the trip.  
To clear/reset the maximum rate of ascent, press and hold the [s/  
+] button for 2 seconds.  
11.4 Ascent Mode - Total Daily Ascent  
12.1 Run Counter - Trip Run Counter  
In ascent mode, press the [o/-] button 3 times to view the total  
daily ascent.  
The total daily ascent is automatically reset at midnight.  
In the run counter mode, the default view is the trip run counter.  
A run is calculated based on altitude adjustment. An additional run  
is added to the total if there is an ascent measured of more than  
60ft. or 20m.  
To reset the total run counter, press and hold the [s/+] button for  
2 seconds.  
11.5 Ascent Mode - Total Lifetime Ascent  
In ascent mode, press the [o/-] button 4 times to view the total  
lifetime ascent.  
To clear/reset the total lifetime ascent, press and hold the [s/+]  
button for 2 seconds.  
continues  
20  
21  
 
 
What is not covered? Normal wear, and damage due to the abrasion, melting,  
misuse, alteration, and abuse (including any disassembly) are not covered by  
this warranty. Digital Watches are water resistant, they are not waterproof.  
Damage resulting from excessive exposure to water, heat or cold is not covered  
under this warranty. Additionally, the battery is not covered under the warranty.  
Always have the battery replaced by an authorized repair center or jewler.  
Should you do the work yourself, you will void this warranty.  
12.2 Run Counter - Daily Run Counter  
To view daily run counter, press the [o/-] button. The total number  
of runs for the day will be displayed.  
A run is calculated based on altitude adjustment. An additional run  
is added to the total when a period of descent is followed by an  
ascent greater than 60ft. or 20m.  
How to obtain warranty service or repair of your watch: Should a defect covered  
by this warranty appear in your watch, call our Consumer Service Department  
toll-free at 1.800.572.8822 for return authorization and instructions. (You must  
pay the cost of returning the unit to us). If the product is found to be defective  
in material or workmanship, we shall, at our option, either repair or replace it  
without charge, and will pay the cost of return shipment to you. If repairs are  
required to correct any problem not covered by this warranty, we will contact  
you for approval to proceed and to charge you for the components repaired or  
replaced, plus a nominal charge for labor.  
THERE ARE NO EXPRESS WARRANTIES ON YOUR WATCH THAT ARE NOT  
CONTAINED IN THIS DOCUMENT. IN NO EVENT SHALL WE BE LIABLE FOR  
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM USING OR  
LOSS OF USE OF YOUR WATCH.  
The daily run counter is automatically reset at midnight.  
12.3 Run Counter - Lifetime Run Counter  
To view the lifetime run counter, press the [o/-] button. The lifetime  
number of runs for the watch will be displayed.  
A run is calculated based on altitude adjustment. An additional run  
is added to the total when a period of descent is followed by an  
ascent greater than 60ft. or 20m.  
To reset/clear the lifetime run counter, press and hold the [s/+]  
button for 2 seconds.  
13.0 Limited Warranty:  
What is covered? Johnson Outdoors Inc. warrants your Tech4o Watch to be  
free from defects in materials or workmanship, and to perform accurately, for  
one (1) year provided it has not been damaged by the causes described in the  
next paragraph.  
Some states do not allow exclusion or limitation of incidental or consequential  
damages, so the above exclusion may not apply to you.  
This warranty gives you specific legal rights, and you may have other rights  
which vary from state to state.  
22  
23  
 
 

TP Link Network Router TX 6610 User Manual
Trango Broadband Network Router M2400S User Manual
Traulsen Air Conditioner TU048QC User Manual
Troy Bilt Blower 769 06521 P00 User Manual
True Manufacturing Company Refrigerator TBB 2 User Manual
Uniden Radio PRO630XL User Manual
Univex Blower 358798380 User Manual
Vandersteen Audio Portable Speaker VCC 5 User Manual
Vivotek Digital Camera PT3112 User Manual
Vulcan Hart Cooktop GTS12 1 User Manual