Tekkeon Marine Battery MP3450 10 User Manual

MP3450i/MP3450-10 User Guide  
 
USER GUIDE  
Contents  
Overview..............................................................................................................2  
Getting Started ....................................................................................................2  
Unpacking myPower ALL Plus ........................................................................2  
Getting to Know myPower ALL Plus ..............................................................3  
Storing myPower ALL Plus ............................................................................3  
Charging myPower ALL Plus ..............................................................................4  
Charging with a Power Adapter ......................................................................4  
Charging with a Solar Panel ............................................................................4  
Using myPower ALL Plus....................................................................................5  
Select/Connect the Adapter Tip........................................................................6  
Connect the Power Output Cord......................................................................6  
Adjust the Voltage Level ..................................................................................7  
Connect the Portable Device............................................................................9  
View myPower ALL Plus Battery Capacity ......................................................9  
Obtaining Adapters ........................................................................................10  
Using the Extended Battery (MP3450-10) ........................................................10  
Adding the Extended Battery ........................................................................10  
Charging the Extended Battery ......................................................................10  
Troubleshooting ................................................................................................11  
Limited Warranty ..............................................................................................12  
Customer Support ............................................................................................13  
 
Overview  
myPower ALL Plus MP3450i is a rugged, high-capacity lithium polymer battery for use with  
instruments or industrial equipment. This universal battery provides instant power for devices that  
require between 5V and 19V, and is targeted to users who prefer a fixed voltage that will not be reset  
upon disconnection of the connected device.  
myPower ALL MP3450i can be used alone, or with the optional extended battery (MP3450-10) to  
double the capacity. The extended battery with mounting brackets is sold separately.  
Getting Started  
Unpacking myPower ALL Plus  
Your myPower ALL Plus package includes the following:  
myPower ALL Plus  
User guide (not shown)  
lithium polymer  
rechargeable battery  
Power output cord  
Voltage Selection  
Card  
Power adapter  
Adapter tip kit with drawstring bag  
(5 adapter tips)  
2
 
Getting to Know myPower ALL Plus  
Capacity Level Indicators  
Charging/Indicator  
Capacity Level Button  
DC OUT  
For connection  
to device  
Voltage Setting  
(Dip Switch)  
ON/OFF  
switch  
DC IN For connection  
to power adapter  
MP3450i  
MP3450-10  
Battery port for connection  
to MP3450-10  
Storing myPower ALL Plus  
Lithium polymer batteries must be used consistently for maximum performance. Therefore, if you do  
not use the battery often, you should complete a charge cycle (discharge/recharge the battery) once  
a month.  
myPower ALL Plus can be used in the environmental temperature range between -4 and 185°F  
(-20 and 85°C). While not in use, store myPower for iPhone in a dry area where the temperature is  
between -4° and 113°F (-20 and 45°C). Extreme temperatures can damage the battery, and the battery  
life will decrease with higher temperatures or a moist environment.  
USER GUIDE  
3
 
Charging myPower ALL Plus  
To charge MP3450i, you can use either the included power adapter or a solar panel. The steps to charge  
with either of these devices are described in this section.  
Charging with a Power Adapter  
myPower ALL Plus will charge in four hours when completely empty. The green CHARGE indicator will  
turn on after the battery is 80% charged. Therefore, you should view the actual battery capacity before  
disconnecting the power adapter to stop charging. (Before using myPower ALL Plus for the first time,  
you must charge the device for four hours.)  
1. Remove the output cord from the DC OUT jack, if connected.  
2. Plug the power adapter into the DC IN jack on the end of myPower ALL Plus.  
3. Plug the power adapter into a wall outlet. The red CHARGE indicator will turn on to indicate the  
battery is charging and is less than 80% charged.  
4. When the green charge indicator turns on, press the Capacity Level Button to view the battery  
capacity. If the capacity does not indicate full (green LEDs on), continue to charge the battery until  
the battery capacity indicates full.  
5. When the battery capacity indicates full, unplug the power adapter.  
NOTE: myPower ALL Plus will automatically shut down the power input when fully charged, so you can  
charge it overnight.  
Charging with a Solar Panel  
You can charge myPower ALL Plus using a compatible solar panel. The solar panel can connect to the  
DC IN port, or the 3-Pin Input Port, depending upon the type of solar panel. The DC IN port is designed  
for use with a DC power adapter with constant current input. Charging myPower ALL Plus efficiently  
requires a minimum of 1A current output from the solar panel. In general, a 25W or higher  
solar panel should provide sufficient power to charge myPower ALL Plus.  
4
 
The 3-Pin Input port is designed to allow charging by smaller solar panels (lower than 25W), and  
requires an optional Smart 3-Pin Adapter available from Tekkeon. To use the solar panel with this port,  
the solar panel must have a minimum open circuit voltage of 15V. However, there is no minimum output  
current requirement from the solar panel.  
Using myPower ALL Plus  
myPower ALL Plus can be used to power and/or charge any device that requires between 5 and 19V.  
With devices that require higher voltage levels, like notebook computers and portable DVD players,  
we recommend that you use myPower ALL Plus only to power the device. You will find that powering  
without charging your higher voltage device will maximize the battery life of myPower ALL Plus, thus  
letting you use your portable device even longer.  
To use myPower ALL Plus to power and/or charge your device, take these steps which are described in  
detail in the following sections.  
• Select an adapter tip for your main device and connect the tip to the output cord.  
• Connect the power output cord to myPower ALL Plus.  
• Adjust the voltage level to match that of your device.  
• Connect the adapter tip/output cord to your device.  
5
USER GUIDE  
 
Select/Connect the Adapter Tip  
1. Select the adapter tip that fits securely into the power jack on your  
portable device.  
2. Locate the polarity symbol on your device in the area around the  
power connector jack:  
Center Positive  
Center Negative  
WARNING: myPower ALL Plus supports Center Positive polarity only. If your device has a Center  
Negative polarity, do not power the device with myPower ALL Plus; contact [email protected]  
for assistance.  
3. Connect the adapter tip to the power output cord  
(but not the device).  
If you are using a UA-xxx adapter (rather than  
PA-xxx), you must insert the L34 adapter between  
the adapter cord and UA-xxx adapter as shown.  
L34 Adapter for  
myPower ALL Plus  
Connect the Power Output Cord  
1. Plug the large end of the power output cord into  
the DC OUT jack on the end of myPower ALL Plus.  
6
 
Adjust the Voltage Level  
1. Locate the voltage specification for your portable device. This can be found on the  
device power adapter label or device specification label which typically is found on  
the bottom of the unit.  
(If available, use the voltage specification shown on the power adapter.)  
2. Using the voltage chart on page 8, adjust the Voltage Setting (dip switch) to  
change the output voltage to that required by your device.  
CAUTION: It is important to set the voltage NO MORE than one step higher than the  
voltage requirement for the portable device as an incorrect setting may prevent  
myPower ALL Plus from working with your device, or may harm your device in the  
rare instance that the device accepts the higher voltage. However, for all devices,  
adjusting the voltage ONLY one step higher than required will not harm the device.  
Sample Power  
Adapter Label  
3. To change the voltage, repeat step 2.  
TIP: You can optimize the use of myPower ALL Plus with your notebook computer or portable DVD  
player by setting the voltage on myPower ALL Plus to less than the required voltage shown on the  
notebook computer power supply. This prevents myPower ALL Plus from charging the device, thus  
extending the amount of time you can use myPower ALL Plus to power your notebook computer.  
Most notebook computers have a battery voltage of 11.1V or 14.8V, allowing them to be powered with  
12V or 14V. Therefore, it is recommended that you set the voltage to 12V first, and then test to see if it  
will power your notebook. If not, increase the voltage to the next voltage level, and retest. Repeat this  
process until you reach the voltage that will power your notebook.  
Most portable DVD players require 9 or 12 volts. Set the voltage to 7.5V and test to see if myPower ALL  
Plus will power your device at this setting. If not, increase the voltage by one level and retest.  
7
USER GUIDE  
 
VOLTAGE CHART  
8
 
Connect the Portable Device  
1. Connect the adapter tip into the power jack on the portable device.  
2. Slide the ON/OFF switch to ON to turn on myPower ALL Plus.  
3. Turn on the portable device and use it as you would normally. While connected, myPower ALL Plus  
will power and charge your device. (As mentioned earlier, myPower ALL Plus will not charge a device  
if the voltage setting is lower than that required.)  
or  
Leave the portable device turned off and myPower ALL Plus will charge the device battery.  
4. When finished, slide the ON/OFF switch to OFF.  
NOTE: If your portable device displays a low voltage/low capacity or double-beep warning while  
myPower ALL Plus is connected, adjust the voltage setting to one level higher.  
TIP: For most portable devices, myPower ALL Plus can be used to power the device even when the  
device battery is not installed.  
View myPower ALL Plus Battery Capacity  
CAPACITY INDICATOR  
The capacity in myPower ALL Plus will decrease as the battery  
powers and/or charges your devices. The remaining capacity is  
displayed on the capacity indicator, which is accessed as  
described below. As the remaining capacity decreases, the  
lights will turn off in sequence from right to left. When the  
myPower ALL Plus battery capacity is low, only one green LED  
will be on. You should recharge myPower ALL Plus at this time.  
When myPower ALL Plus is completely out of battery, all lights  
will be off. At this point, you must charge myPower ALL Plus.  
INDICATOR  
PERCENTAGE  
1-10%  
1st  
2nd  
3rd  
4th  
5th  
6th  
7th  
10-25%  
25-40%  
40-55%  
55-70%  
70-85%  
85-100%  
1. Press the Capacity Level button to view the capacity as  
shown in the Capacity Indicator table.  
9
USER GUIDE  
 
Obtaining Adapters  
Five adapter tips that fit most DC adapter jacks on a variety of portable devices are included with myPower  
ALL Plus. If none of these tips fits snugly into your portable device power jack, please go to our  
web site at www.tekkeon.com/mpadapters to determine which adapter tip you need for your device.  
You can obtain most adapters through the web site, or by contacting Tekkeon by phone at 888-787-5888 or  
1-714-832-1266. If available through Tekkeon, the adapter will be sent to you for a nominal fee.  
Using the Extended Battery (MP3450-10)  
You can double the capacity of myPower ALL Plus by adding the extra battery unit MP3450-10. When  
MP3450-10 is added to MP3450/MP3450i, the battery capacity shown on the indicators includes the  
capacity available with MP3450-10.  
Adding the Extended Battery  
1. Place MP3450i on top of MP3450-10 with both flat silver ends facing the same direction.  
2. Connect the bracket with the 3-pin plugs inside to the silver ends of the devices.  
The 3-pin plugs will mate with the battery port on each of the devices, and the  
controls on the end of MP3450i will show through the bracket opening.  
3. Connect the second bracket on the opposite end of the devices to hold  
the units together securely.  
4. Use MP3450i as you would normally.  
Charging the Extended Battery  
1. With MP3450-10 connected, charge MP3450i as described earlier. Both batteries will be charged at  
the same time (in parallel).  
10  
 
Troubleshooting  
If myPower ALL Plus does not power the portable device or charge the device battery, take these steps:  
1. Verify that the current consumption of the portable device is not more than 4.0 Amp. If the device  
consumes more than the maximum provided by myPower ALL Plus, the device will shut down when  
turned on and cannot be powered and/or charged by myPower ALL Plus.  
2. Verify that the device does not require more than 19V. If the device requires more, MP3450i will not be  
able to charge the device. However, in most but not all cases, MP3450i will be able to power the device.  
3. View the remaining battery capacity. If it is below 25%, recharge myPower ALL Plus.  
4. Check that the output cord is connected to both myPower ALL Plus and the portable device, and that  
the adapter tip fits snugly into the power jack on your portable device. If not, try another adapter.  
5. Verify that the polarity of the device power jack is Center Positive. If the polarity is Center Negative,  
please contact [email protected] for assistance.  
6. Check that the output voltage for your portable device matches or  
is just below the output voltage set on myPower ALL Plus. If the output voltage  
is not correct, change the voltage as required.  
7. Verify that a battery is installed in the portable device as some devices will  
Center Positive  
Symbol  
not function without a battery installed.  
8. Verify if your device is designed with charging circuitry that limits the input  
voltage. If so, myPower ALL Plus may not be able to power or charge the device.  
(For example, if a device is designed to accept only a very narrow input voltage,  
then select the voltage that is as close as possible to that required for your device.  
Otherwise myPower ALL Plus may not be able to power or charge the device.)  
Center Negative  
Symbol  
11  
USER GUIDE  
 
Limited Warranty  
The product enclosed herein is warranted to be free of operational defects for a period of one year from  
the date of purchase. In the event of a defect in operation during the warranty period Tekkeon, Inc. will  
replace the defective product when the owner returns all product contents. The limited warranty will be  
considered void if the unit is tampered with, subject to misuse, negligence or accidental damage, has  
been improperly serviced, or if the security seal is removed. This warranty is limited to replacement only  
and shall not cover any other damages. Any product returned to Tekkeon, Inc. with no fault found will be  
returned to the owner at the owner’s expense.  
To obtain warranty coverage, please complete and submit the enclosed registration card.  
Disclaimer of Warranties  
Any user of this product does so at the user’s own risk. To the maximum extent permitted by applicable  
law, Tekkeon, Inc. and its suppliers provide the hardware and any support services related thereto “as is”  
and with all faults; and hereby disclaim all warranties and conditions, whether express, implied or  
statutory, including, but not limited to implied warranties of merchantability, fitness for a particular  
purpose, non-infringement, lack of negligence or correspondence to description, except for those  
warranties specifically and expressly provided in the Limited Warranty.  
With respect to the use of this product, in no event shall the company be liable for any loss of profit or  
any other commercial damage, including but not limited to special, incidental, consequential and other  
damages.  
12  
 
Customer Support  
Customer support for myPower ALL Plus is available at:  
Tekkeon, Inc.  
c/o myPower ALL Plus  
3002 Dow Avenue, #134  
Tustin, CA 92780  
888-787-5888 / 714-832-1266  
Tekkeon, Inc. must issue a Return Merchandise Authorization (RMA) number for all exchanges  
or refunds.  
 
© 2008 Tekkeon, Inc.  
Rev A  
All Rights Reserved  
myPoweris a trademark  
of Tekkeon, Inc.  
Cut loose. Stay loose.  
 

Technicolor Thomson Cell Phone Accessories CP 2016 007 User Manual
Technics Speaker SB AFC300 User Manual
Toastess Electric Grill TPG 457 User Manual
Toshiba Camcorder B10 User Manual
Toshiba CRT Television 14AF44 User Manual
Toshiba Projection Television 19LV505C User Manual
Tripp Lite Computer Accessories SEC4002RF User Manual
Uniden Scanner UBC9000XLT User Manual
Univex Portable DVD Player PET825 User Manual
Weed Eater Lawn Mower WET2242STD User Manual