Tektronix Printer 200E User Manual

Instruction Sheet  
¨
Phaser 200e  
¨
Phaser 200i  
¨
Phaser 220e  
Upgrading a Phaser¨ 200e, 200i or 220e printer  
to a Phaser¨ 240  
This kit contains the components necessary to upgrade a Phaser 200e, 200i or 220e to a Phaser 240 Color  
Printer. Generally, this involves replacing the printerÕs old image processor board with a new image  
processor board. In the case of the Phaser 200e and 200i, the printerÕs engine control board must also be  
replaced with a new engine control board included in this kit. In all cases, the unused or replaced  
components must be returned to Tektronix. This upgrade should only be installed by qualiÞed service  
personnel.  
Kit contents  
Phaser 240 image processor board  
print engine controller board  
8-Mbyte RAM SIMM  
Ethernet card (Option P1)  
Static electricity precautions  
Plug in the ground adapter (003-1501-00) in an AC outlet. Connect the  
anti-static mat (006-7056-00) to the adapterÕs groundplug.  
Put on your anti-static wrist strap and connect it to the anti-static mat.  
Leave the printer plugged into its power outlet; this preserves a  
ground path for static discharges.  
Touch the printer's bare metal frame often to discharge static  
electricity from your body.  
Handle the circuit board(s) by their edges only.  
Do not lay the board(s) on a metal surface.  
Avoid wearing nylon or polyester clothing; they generate static  
electricity.  
Copyright © 1995 by Tektronix, Inc.. All rights reserved.  
063-1865-AA  
 
Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240  
5. Remove the card cage top (3 screws).  
6. Flip over the hinged card cage top.  
7. Lift out the old image processor board.  
Flip over  
top  
Remove screws  
Lift out image  
processor board  
31865-01  
3
 
Note  
In the next step, it is only necessary to remove the old engine control  
board from a Phaser 200e or Phaser 200i Color Printer.  
8. Disconnect the wiring harnesses leading to the engine control board.  
Card cage  
Disconnect  
harnesses  
31865-02  
9. Lift out the engine control board.  
Lift out  
engine board  
31865-03  
 
Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240  
SIMM installation on the new image processor board  
1.  
If installed, remove the font module by spreading the pawls at each  
end of the font module connector securing the module in place.  
2. Installing the RAM SIMM. Insert the RAM SIMM in connector J7 (a), and  
tilt the card upright until it locks in place (b). When properly inserted,  
a tab on each end of the connector slips into a hole on each end of the  
card. Also, a pawl on each end of the connector latches around each  
end of the card to lock it in place.  
3. Installing the Ethernet card. Insert the Ethernet card in connector J30 (a),  
and tilt the card upright until it locks in place (b). When properly  
inserted, a tab on each end of the connector slips into a hole on each  
end of the card. Also, a metal pawl on each end of the connector  
latches around each end of the card to lock it in place.  
Standard  
RAM SIMM  
a
b
Optional  
RAM SIMM  
Font  
module  
Ethernet  
card  
16-0  
16-1  
16-2  
16-3  
00-0  
00-1  
00-2  
00-3  
a
b
I/O board  
connector  
31865-04  
4. Reinstall the font module, if removed. Like the RAM SIMM, when  
properly inserted, a tab on each end of the connector slips into a hole  
on each end of the card. Also, a pawl on each end of the connector  
latches around each end of the card to lock it in place.  
5
 
Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240  
New image processor install  
1. Slide the new image processor board into its card cage slot.  
Close  
card cage  
top  
Insert image  
processor board  
2. Close the card cage cover and secure it in place.  
3. Reinstall the printer covers.  
6
 
Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240  
4. Connect the I/O boardÕs ribbon cable to the image processor boardÕs  
I/O connector. Tilt the I/O board forward into place against the rear  
of the printerÕs card cage. Secure the I/O board in place with the two  
thumbscrews.  
Install  
I/O board  
Install  
ribbon cable  
31865-06  
5. Reconnect the interface cables. Turn on the printer and examine the  
startup page it should automatically print out. Refer to the Phaser 240  
Color Printer User Manual for details on connecting interface cables and  
making prints.  
7
 
Upgrading a Phaser¨ 200e, 200i or 220e printer to a Phaser¨ 240  
Return the old boards to Tektronix  
1. Repack the old image processor and engine board (new or old) in the  
anti-static bags. Put the anti-static bags inside the shipping box.  
2. In the U.S.A.:  
a. Write the printerÕs original serial number on the shipping return  
label. attach the shipping label to the box, covering the original  
shipping label.  
b. Securely tape the box closed and mail it to the pre-addresses  
location. Postage is prepaid.  
Outside the U.S.A.:  
a. AfÞx the special international shipping return label, included with  
this upgrade kit, to conceal the original U.S. shipping label.  
b. Write the printerÕs serial number on the shipping return label.  
c. Tape the box closed and ship the box to Tektronix, using you  
respective countryÕs shipping method.  
8
 

Tascam Cassette Player D00935220B User Manual
Teledex Telephone Opal RediDock User Manual
Timex Watch W197 User Manual
Toshiba Cash Register Electronic Cash Register User Manual
Triarch Fan CF31020 User Manual
Trion Dust Collector DC Cyclone User Manual
ViewSonic Computer Monitor VS13239 User Manual
Vizualogic Car Video System HindsightTM User Manual
VocoPro Stereo Amplifier DA 8808VE User Manual
VTech Telephone DS4121 3 User Manual