Toastmaster Juicer JM419SSCAN User Manual

Model JM419SSCAN  
INSTRUCTION MANUAL  
 
IMPORTANT SAFEGUARDS  
When using electrical appliances, basic safety precautions should always be  
followed including the following:  
1. Read all instructions.  
2. To protect against risk of electrical shock do not put cord, plugs, or  
appliance in water or other liquid.  
3. Close supervision is necessary when any appliance is used by or  
near children.  
4. Unplug from outlet when not in use, before putting on or taking off  
parts, and before cleaning.  
5. Avoid contacting moving parts.  
6. Do not operate any appliance with a damaged cord or plug or after the  
appliance malfunctions, or is dropped or damaged in any manner.  
Contact Consumer Service for examination, repair or electrical or  
mechanical adjustment.  
7. The use of attachments, including canning jars, not recommended by  
the manufacturer may cause fire, electric shock, or injury.  
8. Do not use outdoors.  
9. Do not let cord hang over edge of table or counter.  
10. Do not let cord contact hot surface, including the stove.  
11. Always make sure Juicer Lid is clamped securely in place before Motor  
is turned ON. Do not unfasten Clamps while Juicer is in operation.  
12. Be sure to press the OFF Button and unplug the Juicer from electrical  
outlet after each use. Make sure the Motor is completely stopped  
before disassembling.  
13. Do not put your fingers or other objects into the Juicer opening while it  
is in operation. If food becomes lodged in opening, use Food Pusher or  
another piece of fruit or vegetable to push it down. When this method  
is not possible turn the Motor OFF, unplug Juicer from electrical outlet,  
and disassemble Juicer to remove remaining food.  
SAVE THESE INSTRUCTIONS  
FOR HOUSEHOLD USE ONLY  
1
 
Additional Important Safeguards  
1. All users of this appliance must read and understand this Instruction  
Manual before operating or cleaning this appliance.  
2. The cord to this appliance should be plugged into a 120V AC  
electrical outlet only.  
3. Do not leave this appliance unattended during use.  
4. If this appliance begins to malfunction during use, immediately press  
the OFF Button and unplug the cord. Do not use or attempt to repair  
the malfunctioning appliance.  
5. IF this appliance falls or accidentally becomes immersed in water,  
unplug it immediately. Do not reach into the water! Do not use  
this appliance after it has fallen into or becomes immersed in water.  
6. To reduce the risk of injury to persons or property, never use this  
appliance in an unstable position.  
7. Do not use this appliance for other than its intended use.  
2
 
POLARIZED PLUG  
This appliance has a polarized plug (one blade is wider than the other).  
To reduce the risk of electric shock, this plug is intended to fit into a  
polarized outlet only one way. If the plug does not fit fully in the outlet,  
reverse the plug. If it still does not fit, contact a qualified electrician.  
Do not attempt to modify the plug in any way.  
SHORT CORD INSTRUCTIONS  
A short power-supply cord is provided to reduce the risk resulting from  
becoming entangled in or tripping over a longer cord.  
Do not use an extension cord with this product.  
ELECTRIC POWER  
If the electrical circuit is overloaded with other appliances, your  
appliance may not operate properly. It should be operated on a separate  
electrical circuit from other appliances.  
3
 
®
YOUR JUICEMAN JM419SSCAN  
PRODUCT MAY VARY SLIGHTLY  
FROM ILLUSTRATIONS  
• Food Pusher (P/N 71174)  
Feed Tube  
Pulp Ejection  
Opening  
• Clear Lid (P/N 71175)  
• Stainless Steel  
Blade Basket (P/N 70458)  
Cutter Blade  
Pulp Spout  
Blade Holder  
(P/N 70457)  
• Stainless Steel  
Juice Bowl (P/N 70459)  
Juice Spout  
Clamps  
Motor Base Hub  
• Stainless Steel  
Motor Base  
Control Panel  
• Pulp Basket  
(P/N 70461)  
Replacement parts available  
(except Motor Base).  
Call (800) 233-9054  
4
 
CONTROL PANEL  
Your Juiceman® JM419SSCAN has a unique control panel, offering two speed options:  
HIGH or LOW. These two speeds ensure optimal rpm to provide maximum juicing  
efficiency (efficiency describes the amount of juice extracted from your produce).  
HIGH SPEED  
Best for harder produce, such as carrots, beets, and pineapple  
HIGH  
LOW  
(with rind). Also recommended for leafy or  
stringy produce such as celery and greens.  
LOW SPEED  
Best for softer produce such as citrus, apples, grapes (with  
stems), melons, peaches (remove pit), and tomatoes. Also  
recommended for ripe produce that has become soft.  
OFF  
OFF  
Press this Button to pause or turn your Juiceman®  
JM419SSCAN OFF.  
®
BEFORE USING THE JUICEMAN JM419SSCAN  
The Juiceman® JM419SSCAN comes almost completely assembled in the box.  
We suggest taking it apart and washing the removable parts in warm water with a  
biodegradable, non-abrasive liquid detergent before the first use. This will eliminate  
any traces of dust or residue from manufacturing or shipping.  
NOTE: Your Juicer may be shipped with a protective cardboard insert between the  
Feed Tube and Cutter Blade (on the Blade Basket). Remove this and any other  
protective packaging before using your Juicer.  
CAUTION: Never rinse or immerse the Motor Base in water or any  
other liquid.  
NOTE: Refer to the Fresh Juice Recipes & Menu Planner for juice recipes, pulp  
recipes, sample menus, and tips on buying, cleaning and storing.  
• Make sure the Blade Basket is securely seated and the Pulp Basket is at the  
rear of the Juicer, ready to catch pulp. To save cleaning time, line the Pulp Basket  
with a plastic produce bag (the kind you put your produce in at the grocery  
store).  
• Place a glass underneath the Juice Spout.  
• Read assembly and disassembly directions. Make sure the Juicer is properly and  
completely assembled. The Juicer will not turn on unless properly assembled.  
5
 
PREPARING FRUITS AND VEGETABLES FOR YOUR JUICER  
• Clean all produce thoroughly, using a natural bristle brush. If you are not using  
organic produce, we recommend using a biodegradable cleaner to help remove  
pesticide residue.  
• Remove and discard the outer leaves of non-organic produce and peel any  
waxed fruit or vegetable.  
Trim away any discolored or bruised sections.  
• The skin may be left on all produce (including pineapple and melons) except  
oranges, grapefruit, and tangerines. The oil found in these skins tastes bitter and  
is difficult to digest.  
• Remove melon seeds when possible, as they may escape through the top of the  
Feed Tube while juicing. The pits of fruits such as cherries, pears, and peaches  
should also be removed.  
• The Juiceman® JM419SSCAN is designed to make juicing easier with an over-  
sized Feed Tube to accomodate larger produce -- feed most whole apples and  
oranges, tangerines, ginger, beets, pineapple or melons. Make sure produce can  
be fed comfortably into the Feed Tube. Use the Food Pusher to gently direct  
produce through the Feed Tube. Never push produce into the Feed Tube with  
your fingers.  
• Leafy greens, parsley, wheat grass, and sprouts should be bunched up into a small,  
tight ball and pushed through with the Food Pusher.  
• Bananas are not suitable for juicing; a clear juice cannot be obtained from them  
and residue left in the machine can clog the micro-mesh screen. Produce such as  
apricots, plums, pears, peaches, and tomatoes should be firm for best results  
when juicing.  
6
 
®
USING THE JUICEMAN JM419SSCAN  
TO TURN YOUR JUICEMAN® JM419SSCAN ON:  
• Make sure that your Juicer is completely and  
properly assembled. See ASSEMBLY  
INSTRUCTIONS.  
Rib on  
Food Pusher  
aligns with  
groove in  
Feed Tube  
• Plug the Juicer into a 120V AC  
electrical outlet.  
• Remove the Food Pusher from the  
Feed Tube.  
• Place produce into the Feed Tube.  
To insert the Food Pusher into the Feed  
Tube, it is necessary turn the Food Pusher to  
align the rib on the Food Pusher with the  
groove in the Feed Tube. The Food Pusher’s  
grooved bottom edge directs food through  
the Feed Tube and Blade Basket.  
• Press HIGH Speed Button for  
harder produce.  
• Press LOW Speed Button for softer produce.  
• When juicing a combination of hard and soft produce, such as carrots and  
apples, you will want to use HIGH speed for the carrots and LOW speed for  
the apples. You do not have to turn the machine OFF to change speeds. Simply  
press the appropriate Speed Button for each type of produce being juiced.  
Tip: Try alternating types of produce to ensure maximum efficiency.  
TO TURN YOUR JUICEMAN® JM419SSCAN OFF:  
• Press the OFF Button. Unplug the Juicer from the outlet when not in use.  
7
 
DISASSEMBLY INSTRUCTIONS  
Step One: Remove Clamps  
Place thumb onto center dot on Clamp and place  
fingers under bottom of Clamp. Pull bottom of  
Clamp out and push Clamp up. Allow top of  
Clamp to swing out. Repeat for opposite Clamp.  
Step Two: Remove Juice Bowl Assembly  
Grasp the sides of the Stainless Steel Juice  
Bowl. Carefully lift off the Stainless Steel Juice  
Bowl, Blade Holder, Blade Basket, and Lid as  
one piece. These pieces will then come apart  
for easy cleaning. (See CLEANING YOUR  
JUICER for cleaning instructions.)  
CAUTION: Use care when handling Blade  
Basket; the Cutter Blades are very sharp!  
8
 
ASSEMBLY INSTRUCTIONS  
ALWAYS MAKE SURE JUICER IS UNPLUGGED BEFORE STARTING ASSEMBLY.  
NOTE: For your juicing convenience, your Juiceman® JM419SSCAN can be  
assembled for right-hand or left-hand use. Right hand use allows the user to place  
produce into the Feed Tube with the left hand while operating the Food Pusher  
with the right hand. If you are left-handed, or feel the juicing operation is  
uncomfortable, you can reverse the assembly instructions below so the Juice Spout  
is to the rear of the unit (and all subsequent parts will face the opposite way).  
Left Hand Assembly  
Right Hand Assembly  
Step One: Place Juice Bowl  
Place Juice Bowl on top of the Motor Base so  
that the Juice Spout is to the front (over the  
Juiceman® logo). Align four tabs on underside  
of Juice Bowl with four Buttons on the Motor  
Base. Lower Juice Bowl onto Base and rotate  
slightly to fit Tabs over the Buttons.  
Step Two: Place Blade Holder  
Place Blade Holder on top of the Juice Bowl so  
the Pulp Spout is opposite the Juice Spout.  
Align square tab on underside rim of Blade  
Holder with bend in rim of Juice Bowl. When  
seated properly, the Blade Holder will turn  
only slightly.  
9
 
ASSEMBLY INSTRUCTIONS (Continued)  
Step Three: Place Blade Basket  
Grasp Blade Basket around top rim with both  
hands and center Basket over Motor Base Hub.  
Carefully lower Blade Basket onto Hub and rotate  
slightly until it drops into position and is seated  
properly. When seated properly, the Blade Basket  
will not lift out of the Blade Holder and will  
spin freely.)  
CAUTION: Use care when handling the Blade  
Basket; the Cutter Blades are very sharp!  
Step Four: Place Clear Lid  
Align Clear Lid so Pulp Ejection Opening is over  
the Pulp Spout. Place cut-outs in the Lid over the  
matching cut-outs in the rim of the Blade Holder.  
Step Five: Attach Clamps  
While holding Clamp from the bottom, push  
Clamp up and in until top of Clamp rests in slot  
on the Lid. Place thumb onto center dot on  
Clamp and firmly press in until the bottom  
of the Clamp snaps into place. Repeat for the  
opposite Clamp.  
Step Six: Place Pulp Collector  
Place the Pulp Basket under the Pulp Ejection  
Opening on the Clear Lid. The Pulp Basket will fit  
snugly against the edge of the Juicer.  
Step Seven: Store Food Pusher in Feed Tube  
Turn the Food Pusher to align with the groove in  
the Feed Tube. Store Food Pusher in the Feed  
Tube of the Lid until you are ready to juice.  
10  
 
CLEANING YOUR JUICER  
• Unplug from outlet before assembling or removing parts and  
before cleaning.  
Do not immerse the Motor Base in water or spray it with water.  
Clean only by wiping with a damp sponge, cloth, or paper towel.  
Use any liquid dishwashing detergent but do not use any products  
containing ammonia or scouring powders. These products will  
dull, scratch or mar the plastic surface.  
• All parts (except the Motor Base) are washable in warm, soapy  
water. Follow DISASSEMBLY INSTRUCTIONS. To clean the  
Juicer Lid and Juice Bowl, we recommend using a fruit and  
vegetable brush with natural fibers.  
DO NOT USE A METAL BRUSH OR PAD.  
• When cleaning the Blade Basket, use the brush to make sure  
the tiny holes in the Basket are not clogged. This can be  
accomplished by holding the Blade Basket under a running  
faucet while brushing the Basket holes from both inside and  
outside the Blade Basket.  
• Occasionally, the Juice Bowl, Juicer Lid, and Blade Basket may  
be washed in a dishwasher, only if they are placed on the top  
shelf of the dishwasher. However, washing with ordinary warm  
(not hot) tap water on a daily basis should be sufficient.  
PLEASE NOTE:  
• Sponge off the Motor Base and the legs underneath if any juice  
has spilled under the Juicer. Use a damp toothbrush or cloth to  
clean juice from inside the Hub on top of the Motor Base.  
Juicer should be air-dried only!  
Clean Your  
Juicer  
Thoroughly  
Before Retiring  
For The Day  
Due to the powerful staining properties of the carotenoids that are  
found in many vegetables, especially carrots, we suggest the  
following cleaning procedures:  
• Stained parts may be soaked overnight in any of these solutions:  
(1) biodegradable soap in enough warm water to cover Juicer  
parts, (2) 1/4 cup bleach added to a sink full of warm water,  
(3) 1 part warm water to 1 part cider vinegar or (4) 1/2 small  
box baking soda in enough warm water to cover parts.  
• Never use ammonia or abrasives.  
• Lightly scrub with soft bristle brush and liquid detergent  
after soaking.  
NEVER SUBMERGE THE MOTOR BASE IN WATER OR OTHER LIQUID!  
11  
 
CLEANING YOUR JUICER (Continued)  
Any other  
After cleaning and reassembly is complete, your new Juicer is ready  
to go to work! Before starting, make sure the Blade Basket is  
securely seated and the Pulp Basket is at the rear of the Juicer to  
receive pulp. The pulp from your Juicer can be used in many  
different applications such as breads, muffins, cakes, soup stocks,  
compressed facial packs and garden compost material.  
servicing  
should be  
performed by  
authorized  
personnel only  
Unplug unit and allow to cool. Clean the Juicer following the  
procedures described in this Instruction Manual.  
STORAGE  
Store the Juicer in its box or in a clean, dry place. Never store the  
Juicer while it is hot or still plugged in. Never wrap cord tightly  
around appliance. Do not put any stress on cord where it enters  
the unit, as this could cause cord to fray and break.  
12  
 
TROUBLESHOOTING  
Symptom  
Possible Correction  
Pulp builds up  
excessively in the  
back of  
Try juicing slower, as wet produce is more likely to build up in Lid.  
To release pulp, lightly tap on the side of the Lid. Empty Pulp  
Basket if full.  
the Juicer Lid.  
Bottom of  
Feed Tube is  
damaged.  
Blade Basket may not have been seated correctly, causing it to  
become unseated during use. Should this be the case, check the  
gear teeth of the Blade Basket and the Motor Base for damage. If  
any teeth are damaged, call Consumer Service at (800) 233-9054.  
Blade Basket is  
difficult to:  
• insert onto  
the Hub;  
remove from  
the Hub.  
Snug seating is desirable. To insert, try seating the Blade Basket  
on a different Hub position. To remove, turn Juice Bowl in a  
clockwise direction.  
Too much pulp  
builds up on  
Blade Basket.  
This may be an isolated situation resulting from the varied texture  
and moisture content of the produce. Stop juicing, scrape off pulp  
and begin again, alternating types of produce.  
Excessive noise or  
vibrations occur  
after Juicer is  
turned on.  
Pulp may have built up on the Blade Basket. Clean the Blade  
Basket and try alternating different types of produce while juicing.  
Note: Because of the Juiceman’s powerful motor, a small amount of  
noise and/or vibration is normal when the Juicer is turned on and as  
it comes to a complete stop. All Juicers will sound slightly different.  
Juice sprays out  
of the Spout.  
Juice the produce as slowly as possible. Keep the Pulp Basket  
emptied for good air flow through machine.  
Juice leaks  
between Juice  
Bowl and Lid.  
Juice slowly so that the Blade Basket does not fill up too quickly  
with juice. Keep Pulp Basket emptied to allow good air flow  
through the machine.  
Pulp in juice.  
Juice slowly to avoid excessive pulp buildup inside the Lid and  
Juice Bowl.  
13  
 
TROUBLESHOOTING (Continued)  
Symptom  
Possible Correction  
Improper fit between the Blade Basket and Hub can cause parts of  
the Juice Bowl to rub against the Blade Basket. If this is the case,  
call Consumer Service at (800) 233-9054.  
Inside rim of  
Juice Bowl is  
worn or  
chipped (inside  
lower rim or  
inside upper  
rim).  
Juice at LOW Speed Setting. Certain produce (pineapples and overripe  
produce) may build up on Blade Basket, causing pulp to eject before  
juice is completely extracted. Fruit tends to produce wetter pulp than  
vegetables. If problem persists, rinse Blade Basket.  
Wet pulp.  
Try a different wall outlet. Also let Juicer sit for about an hour without  
turning it on; moisture may have collected on the circuit board,  
causing machine to shut OFF. If situation is not resolved, call  
Consumer Service at (800) 233-9054.  
Juicer stopped  
while juicing.  
Try a different wall outlet. Also, try using both the HIGH and LOW  
Speed Buttons. Check the Juicer Lid, Blade Basket, and Juice Bowl to  
see if they are properly seated, making sure that the column is  
completely aligned and the safety switch is engaged.  
Juicer does not  
turn ON.  
14  
 
LIMITED ONE-YEAR WARRANTY  
Warranty Coverage: This product is warranted to be free from defects in materials or  
workmanship for a period of one (1) year from the original purchase date. This product  
warranty is extended only to the original consumer purchaser of the product and is not  
transferable. For a period of one (1) year from the date of original purchase of the  
product, our Repair Center will, at its option, either (1) repair the product or (2) replace  
the product with a reconditioned comparable model. These remedies are the  
purchaser's exclusive remedies under this warranty.  
Warranty Service: To obtain warranty service, you must call our warranty service  
number at 1-800-233-9054 for return instructions on how to deliver the product, in  
either the original packaging or packaging affording an equal degree of protection to  
the Repair Center specified below. You must enclose a copy of your sales receipt or  
other proof of purchase to demonstrate eligibility for warranty coverage.  
To return the appliance, ship to:  
To contact us, please write to, call, or email:  
ATTN: Repair Center  
708 South Missouri Street  
Macon, MO 63552 USA  
Consumer Relations Department  
PO Box 7366  
Columbia MO 65205-7366 USA  
1-800-233-9054  
What Is Not Covered: This warranty does not cover damage resulting from misuse,  
accident, commercial use, improper service or any other damage caused by anything  
other than defects in material or workmanship during ordinary consumer use. This  
warranty is invalid if the serial number has been altered or removed from the product.  
This warranty is valid only in the United States and Canada.  
LIMITATION ON DAMAGES: THERE SHALL BE NO LIABILITY FOR ANY INCIDENTAL  
OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED  
WARRANTY OR CONDITION ON THIS PRODUCT.  
DURATION OF IMPLIED WARRANTIES: EXCEPT TO THE EXTENT PROHIBITED BY  
APPLICABLE LAW, ALL IMPLIED WARRANTIES AND CONDITIONS, INCLUDING,  
WITHOUT LIMITATION, IMPLIED WARRANTIES AND CONDITIONS OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE OR USE ON THIS  
PRODUCT ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.  
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential  
damages, or allow limitations on how long an implied warranty lasts, so the above  
limitations or exclusions may not apply to you. This warranty gives you specific legal  
rights and you may have other rights under the laws of your jurisdiction.  
For more information on our products, visit our website:  
©2005 All rights reserved.  
Made in China  
P/N 61724CAN  
7/05  
 

Teac CRT Television CT W32ID User Manual
TOA Electronics Home Theater Server D1440901 User Manual
Toshiba MP3 Player SD V65HT User Manual
Toshiba Network Card MK1504GAL User Manual
Tripp Lite Surge Protector TLP31SAT User Manual
U Line Refrigerator 2015WC User Manual
Uniden Cordless Telephone D13842BK User Manual
Vanguard Managed Solutions Electric Heater FB32NCA User Manual
Vector Automobile Parts VEC021APC User Manual
Vornado Fan TH1 User Manual