Toshiba Copier eSTUDIO550 User Manual

DIGITAL PLAIN PAPER COPIER  
OPERATOR'S MANUAL  
FOR PRINTER FUNCTION  
NETWORK PRINTER BOARD GA-1140  
QUICK START GUIDE  
 
TABLE OF CONTENTS  
I NOTICE/WARNING ....................................................................... 3  
FCC NOTICE/FOR EUROPEAN MODELS ONLY .......................................... 4  
FCC NOTICE ............................................................................................... 4  
FOR EUROPEAN MODELS ONLY.............................................................. 4  
TRADEMARKS/COPYRIGHT......................................................................... 5  
TRADEMARKS............................................................................................ 5  
COPYRIGHT ............................................................................................... 5  
CAUTION/WARNING ...................................................................................... 6  
I SOFTWARE LICENSE AGREEMENT .......................................... 7  
SOFTWARE LICENCE AGREEMENT............................................................ 8  
LICENSE ..................................................................................................... 8  
PROPRIETARY RIGHTS ............................................................................. 9  
CONFIDENTIALITY ..................................................................................... 9  
REMEDIES .................................................................................................. 9  
LIMITED WARRANTY AND DISCLAIMER ................................................ 10  
LIMITATION OF LIABILITY ........................................................................ 10  
EXPORT CONTROLS ............................................................................... 11  
GOVERNMENT USE ................................................................................. 11  
THIRD PARTY BENEFICIARY................................................................... 11  
GENERAL.................................................................................................. 11  
I INTRODUCTION ......................................................................... 13  
ABOUT THE MANUALS ............................................................................... 14  
ABOUT THE QUICK START GUIDE.......................................................... 14  
ABOUT THE MANUALS ............................................................................ 14  
I SYSTEM REQUIREMENTS ........................................................ 17  
SYSTEM REQUIREMENTS ......................................................................... 18  
CONNECTOR CABLE ............................................................................... 18  
FOR WINDOWS ........................................................................................ 18  
FOR MACINTOSH ..................................................................................... 19  
TOPACCESS ............................................................................................. 19  
NETWORK SERVER ................................................................................. 19  
1
 
I SETUP FLOW AND UTILITY ...................................................... 21  
SETUP FLOW CHART.................................................................................. 22  
FOR WINDOWS ........................................................................................ 22  
For Parallel Connection .......................................................................... 22  
For SMB Printing .................................................................................... 23  
For LPR Printing ..................................................................................... 24  
For IPP Printing ...................................................................................... 25  
For Novell Network ................................................................................. 26  
FOR MACINTOSH ..................................................................................... 28  
I SPECIFICATIONS ....................................................................... 29  
SPECIFICATIONS......................................................................................... 30  
PRINTER BOARD ..................................................................................... 30  
OPTIONS................................................................................................... 31  
PS3 Upgrade .......................................................................................... 31  
PS3 Scan & HDD Upgrade..................................................................... 31  
Expansion Memory................................................................................. 31  
Dongle for DocBuilder Pro 1.5 ................................................................ 31  
2
 
NOTICE/WARNING  
3
 
FCC NOTICE/FOR EUROPEAN MODELS ONLY  
FCC NOTICE  
This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference when the equipment is operated in a commercial environment. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference in which case  
the user will be required to correct the interference at his own expense.  
WARNING:  
Changes or modification made to this equipment, not expressly approved by Toshiba TEC or  
parties authorized by Toshiba TEC could void the user’s authority to operate the equipment.  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est conformé à la norme NMB-003 du Canada.  
FOR EUROPEAN MODELS ONLY  
WARNING:  
This product complies with Class A for network connection. In a domestic environment this  
product may cause radio interference in which case the user may be required to take adequate  
measures.  
1. Do not touch the connector terminal when disconnecting the cables of peripheral equipment.  
2. Before opening any covers or removing any parts from the copier, discharge the static electricity from  
your body by touching a metal part of the copier.  
This product is carrying the CE-Mark in accordance with the related European Directives. Responsible  
for CE-marking is TOSHIBA TEC GERMANY IMAGING SYSTEMS GmbH Carl-Schurz-Str. 7, 41460  
Neuss, Germany. e-mail: [email protected]  
4
 
TRADEMARKS/COPYRIGHT  
TRADEMARKS  
Trademarks described in this manual:  
G Ethernet is a registered trademark of US Xerox Corporation.  
G The official name of Windows 95 is Microsoft Windows 95 Operating System.  
G The official name of Windows 98 is Microsoft Windows 98 Operating System.  
G The official name of Windows Me is Microsoft Windows Millennium Edition Operating System.  
G The official name of Windows 2000 is Microsoft Windows 2000 Operating System.  
G The official name of Windows XP is Microsoft Windows XP Operating System.  
G Microsoft, Windows, Windows NT, Microsoft Internet Explorer, and the brand names and product  
names of other Microsoft products are trademarks or registered trademarks of US Microsoft  
Corporation in the US and other countries.  
G Apple, AppleTalk, Macintosh, Mac OS, and LaserWriter are trademarks of US Apple Computer Inc.  
in the US and other countries.  
G PostScript and PostScript Logo are trademarks of Adobe Systems Incorporated.  
G IBM PC/AT is a registered trademark of US International Business Machine Corporation.  
G UNIX is a registered trademark in the USA and other countries, licensed by X/Open Company Ltd.  
G Agfa Font Manager is the trademark of Agfa Monotype Corporation.  
G EFI, Fiery, the Fiery logo, Fiery Driven and RIP-White-Print are registered trademarks of Electronics  
For Imaging, Inc. in the U.S. Patent and Trademark Office and/or certain other foreign jurisdictions.  
G The Electronics For Imaging Logo, the Fiery Driven logo, Command WorkStation, DocBuilder Pro,  
Fiery X3e, Fiery FreeForm, Fiery Scan, Fiery ScanBuilder, Fiery WebInstaller, Fiery WebScan, Fiery  
WebSpooler, Fiery WebStatus, Fiery WebTools, NetWise, Velocity, Velocity Balance, Velocity Build,  
Velocity Design, Velocity Estimate, and Velocity Scan are trademarks of Electronics For Imaging,  
Inc.  
G AMD is a trademark of Advanced Micro Devices, Inc.  
G Pentium and Celeron are trademarks or registered trademarks of Intel Corporation.  
G Other company names and product names in this manual are the trademarks or registered  
trademarks of their respective companies.  
COPYRIGHT  
Copyright © TOSHIBA TEC Corp. 2002 All Rights Reserved. Under the copyright laws, this manual  
cannot be reproduced in any form without prior written permission of Toshiba TEC. No patent liability is  
assumed, with respect to the use of the information contained herein.  
5
 
CAUTION/WARNING  
No part of this manual may be copied in whole or part without permission.  
The contents of this manual may change without notification.  
6
 
SOFTWARE LICENSE  
AGREEMENT  
7
 
SOFTWARE LICENCE AGREEMENT  
YOU SHOULD CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE USING  
THIS SOFTWARE. IF YOU DO NOT AGREE TO THE TERMS AND CONDITIONS OF THIS  
AGREEMENT, DO NOT USE THE SOFTWARE. INSTALLING OR USING THE SOFTWARE  
INDICATES THAT YOU AGREE TO AND ACCEPT THE TERMS OF THIS AGREEMENT. IF YOU DO  
NOT AGREE TO ACCEPT THE TERMS OF THIS AGREEMENT YOU MAY RETURN THE UNUSED  
SOFTWARE FOR A FULL REFUND TO THE PLACE OF PURCHASE.  
LICENSE  
Electronics For Imaging, Inc.grants you a non-exclusive, non-transferable license to use the software and  
accompanying documentation ("Software") included with the controller GA-1140 for TOSHIBA  
e-STUDIO550/650/810 Series printer you have purchased, including without limitation PostScript® soft-  
ware provided by Adobe Systems Incorporated.  
You may:  
a. use the Software solely for your own customary business purposes and solely with the controller GA-  
1140 for TOSHIBA e-STUDIO550/650/810 Series;  
b. use the digitally-encoded machine-readable outline and bitmap programs ("Font Programs") provided  
with the controller GA-1140 for TOSHIBA e-STUDIO550/650/810 Series in a special encrypted  
format ("Coded Font Programs") to reproduce and display designs, styles, weights, and versions of  
letters, numerals, characters and symbols ("Typefaces") solely for your own customary business  
purposes on a monitor used with the controller GA-1140 for TOSHIBA e-STUDIO550/650/810  
Series;  
c. use the trademarks used by Electronics For Imaging to identify the Coded Font Programs and  
Typefaces reproduced therefrom ("Trademarks"); and  
d. assign your rights under this Agreement to a transferee of all of your right, title and interest in and to  
the controller GA-1140 for TOSHIBA e-STUDIO550/650/810 Series provided the transferee agrees  
to be bound by all of the terms and conditions of this Agreement.  
You may not:  
a. make use of the Software, directly or indirectly, to print bitmap images with print resolutions of  
greater than 600 dots per inch, or to generate fonts or typefaces for use other than with the controller  
GA-1140 for TOSHIBA e-STUDIO550/650/810 Series;  
b. make or have made, or permit to be made, any copies of the Software, Coded Font Programs,  
accompanying documentation or portions thereof, except as necessary for use with the controller  
GA-1140 for TOSHIBA e-STUDIO550/650/810 Series purchased by you; provided, however, that  
8
 
under no circumstances may you make or have made, or permit to be made, any copies of that  
certain portion of the Software which has been included on the controller GA-1140 for TOSHIBA e-  
STUDIO550/650/810 Series hard disk drive or ROM. You may not copy the documentation;  
c. attempt to alter, disassemble, decrypt or reverse engineer the Software, Coded Font Programs.  
d. rent or lease the Software.  
PROPRIETARY RIGHTS  
You acknowledge that the Software, Coded Font Programs, Typefaces, and Trademarks are proprietary  
to Electronics For Imaging and its suppliers and that title and other intellectual property rights therein  
remain with Electronics For Imaging and its suppliers. Except as stated above, this Agreement does not  
grant you any right to patents, copyrights, trade secrets, trademarks (whether registered or unregistered),  
or any other rights, franchises or licenses in respect of the Software, Coded Font Programs, Typefaces,  
or Trademarks.You may not adapt or use any trademark or trade name which is likely to be similar to or  
confusing with that of Electronics For Imaging or any of its suppliers or take any other action which impairs  
or reduces the trademark rights of Electronics For Imaging or its suppliers. The trademarks may only be  
used to identify printed output produced by the Coded Font Programs. At the reasonable request of  
Electronics For Imaging, you must supply samples of any Typeface identified with a trademark.  
CONFIDENTIALITY  
You agree to hold the Software and Coded Font Programs in confidence, disclosing the Software and  
Coded Font Programs only to authorized users having a need to use the Software and Coded Font  
Programs as permitted by this Agreement and to take all reasonable precautions to prevent disclosure to  
other parties.  
REMEDIES  
Unauthorized use, copying or disclosure of the Software, Coded Font Programs, Typefaces, or Trade-  
marks will result in automatic termination of this license and will make available to Electronics For Imag-  
ing other legal remedies.  
9
 
LIMITED WARRANTY AND DISCLAIMER  
Electronics For Imaging warrants that, for a period of ninety (90) days from the date of delivery to you, the  
Software under normal use will perform without significant errors that make it unusable. Electronics For  
Imaging's entire liability and your exclusive remedy under this warranty (which is subject to you returning  
the controller GA-1140 for TOSHIBA e-STUDIO550/650/810 Series to Electronics For Imaging or an  
authorized dealer) will be, at Electronics For Imaging's option, to use reasonable commercial efforts to  
attempt to correct or work around errors, to replace the Software with functionally equivalent software, or  
to refund the purchase price and terminate this Agreement. Some states/jurisdictions do not allow limita-  
tions on duration of implied warranty, so the above limitation may not apply to you.  
For warranty service, please contact your authorized service/support center.  
EXCEPT FOR THE ABOVE EXPRESS LIMITED WARRANTY, ELECTRONICS FOR IMAGING MAKES  
AND YOU RECEIVE NO WARRANTIES OR CONDITIONS ON THE SOFTWARE OR CODED FONT  
PROGRAMS, EXPRESS, IMPLIED, STATUTORY, OR IN ANY OTHER PROVISION OF THIS AGREE-  
MENT OR COMMUNICATION WITH YOU, AND ELECTRONICS FOR IMAGING SPECIFICALLY DIS-  
CLAIMS ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE. Electronics For Imaging does not warrant that the operation of the software  
will be uninterrupted or error free or that the Software will meet your specific requirements.  
LIMITATION OF LIABILITY  
IN NO EVENT WILL ELECTRONICS FOR IMAGING OR ITS SUPPLIERS BE LIABLE FOR ANY DAM-  
AGES, INCLUDING LOSS OF DATA, LOST PROFITS, COST OF COVER OR OTHER SPECIAL, INCI-  
DENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES ARISING FROM THE USE OF THE SOFT-  
WARE, OR CODED FONT PROGRAMS, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY.  
THIS LIMITATION WILL APPLY EVEN IF ELECTRONICS FOR IMAGING OR ANY AUTHORIZED  
DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. YOU ACKNOWLEDGE  
THATTHE PRICE OFTHE CONTROLLER GA-1140 FORTOSHIBA e-STUDIO550/650/810 Series RE-  
FLECTS THIS ALLOCATION OF RISK. BECAUSE SOME STATES/JURISDICTIONS DO NOT ALLOW  
THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES,  
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.  
10  
 
EXPORT CONTROLS  
You agree that you will not export or re-export the Software or Coded Font Programs in any form without  
the appropriate United States and foreign government licenses.Your failure to comply with this provision  
is a material breach of this Agreement.  
GOVERNMENT USE  
Use, duplication or disclosure of the Software by the United States Government is subject to restrictions  
as set forth in subdivision (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at  
DFARS 252.227-7013 or in subparagraphs (c) (1) and (2) of the Commercial Computer Software-Re-  
stricted Right Clause at 48 CFR 52.227-19, as applicable.  
THIRD PARTY BENEFICIARY  
You are hereby notified that Adobe Systems Incorporated, a California corporation located at 345 Park  
Avenue, San Jose, CA 95110-2704 ("Adobe") is a third-party beneficiary to this Agreement to the extent  
that this Agreement contains provisions which relate to your use of the Fonts, the Coded Font Programs,  
the Typefaces and the Trademarks licensed hereby. Such provisions are made expressly for the benefit  
of Adobe and are enforceable by Adobe in addition to Electronics for Imaging.  
GENERAL  
This Agreement will be governed by the laws of the State of California.  
This Agreement is the entire agreement held between us and supersedes any other communications or  
advertising with respect to the Software and Coded Font Programs.  
If any provision of this Agreement is held invalid, the remainder of this Agreement shall continue in full  
force and effect.  
If you have any questions concerning this Agreement, please see Electronics For Imaging's web site at  
11  
 
12  
 
INTRODUCTION  
13  
 
ABOUT THE MANUALS  
ABOUT THE QUICK START GUIDE  
Thank you for purchasing the TOSHIBA e-STUDIO550/650/810, GA-1140 Printer Board.  
This QUICK START GUIDE provides the setup flow for installation of the e-STUDIO550/650/810  
Printer Unit and contents of the printer reference manuals. The reference manuals for users and  
system administrators are found on the User Documentation CD-ROM which is shipped with this  
product.  
ABOUT THE MANUALS  
The manuals are included in the User Documentation CD-ROM.  
In oder to display the manuals, Adobe® Acrobat® Reader4.0 or later is required. If you do not have  
Acorbat Reader, it is also included in the User Documentation CD-ROM.  
The following reference manuals may be found on the enclosed User Documentation CD-ROM.  
- User’s Guide (Users Guide.pdf) describes how to install the user softwares and how to operate  
printing from workstations.  
The contents for the manual are shown below:  
- Introduction  
- Installing User Software on a Windows Computer  
- Installing User Software on a Mac OS Computer  
- Printing from Windows Computers  
- Printing from Mac OS Computers  
- Advanced Features  
- Tracking and Managing Print Jobs  
- Troubleshooting  
- Appendix  
- Administrator’s Guide (Administrators Guide.pdf) describes how to set up the TOSHIBA GA-1140  
printer on a network and administer the printer.  
The contents for the manual are shown below:  
- Introduction  
- Preparing for GA-1140 Setup  
- Setting up Network Servers  
- Setting up the Network Setup Options  
14  
 
- Setting up the Printer Setup Options  
- Setting up the TopAccess Setup Options  
- Administrative Functions  
- Troubleshooting  
- Appendix  
If you have the PS3 Scan & HDD Upgrade kit (GE-1060 + GE-1110), the following reference manuals  
are found on the enclosed User Documentation CD-ROM for PS3 Scan & HDD Upgrade.  
- Fiery Utilities Guide (Fiery Utilites Guide.pdf) describes how to use optional softwares such as  
Fiery WebTools, Command WorkStation, FreeForm, and DocBuilder Pro.  
The contents for the manual are shown below:  
- Introduction  
- Using Fiery WebTools  
- Using Command WorkStaion  
- Using DocBuiler Pro  
- Troubleshooting  
- Scan & E-mail Service Guide (Scan & E-mail Service Guide.pdf) describes how to set up the  
optional scan and e-mail service features on the GA-1140 and operate scanning.  
The contents for the manual are shown below:  
- Introduction  
- Installing the User Software  
- Setting up and Administering  
- Scanning  
- Using Fiery E-mail Service  
- Appendix  
15  
 
16  
 
SYSTEM REQUIREMENTS  
17  
 
SYSTEM REQUIREMENTS  
The e-STUDIO550/650/810 GA-1140 print controller operates in the following environments.  
CONNECTOR CABLE  
For Local Environment  
Be sure to use the correct type of cable.  
IEEE 1284 printer cable (Compatible mode, ECP)  
For Network Environment  
Be sure to use the correct type of cable and network device for your network interface card.  
10BASE-T/100BASE-TX  
STP cable with a Category 5 RJ-45 connector.  
FOR WINDOWS  
This machine can be used in local mode via a parallel printer cable, on a network via TCP/IP or IPX/  
SPX.  
Hardware  
Display Resolution  
Display Color  
CPU  
: 1024 x 768 dots or more  
: High Color (16bit) or higher is recommended  
: 80486, AMD, or Pentium processor  
Memory  
Windows 95  
Windows 98  
: 16MB or more  
: 24MB or more  
Windows Me and Windows NT 4.0  
Windows 2000 and Windows XP  
: 32MB or more  
: 64MB or more  
OS  
Microsoft Windows 95 Operating System, English Version  
Microsoft Windows 98 Operating System, English Version  
Microsoft Windows Me Operating System, English Version  
Microsoft Windows NT Workstation Operating System 4.0 with Service Pack 6 or later, English Version  
Microsoft Windows NT Server Network Operating System 4.0 with Service Pack 6 or later, English Version  
Microsoft Windows 2000 Professional Operating System with Service Pack 2 or later, English Version  
Microsoft Windows 2000 Server Operating System with Service Pack 2 or later, English Version  
Microsoft Windows XP Home Edition Operating System, English Version  
Microsoft Windows XP Professional Operating System, English Version  
18  
 
FOR MACINTOSH  
This machine can be used on the network via AppleTalk (Ethernet).  
Hardware  
Display Resolution  
OS  
Mac OS 8.6 to 9.2, Mac OS X (Classic Mode only)  
: 1024 x 768 dots or more  
TOPACCESS  
TopAccess can be used in the following environment:  
Applicable OS  
WWW Browser  
Protocol  
: Windows 95, Windows 98, Windows Me, Windows NT 4.0, Windows  
2000, Windows XP, and Mac OS 8.6 or later  
: Netscape Communicator 4.5 or later, and Java enabled or Microsoft  
Internet Explorer 5.5 and Service Pack 2, or later with Java enabled.  
: TCP/IP  
NETWORK SERVER  
Printing can be performed with the following network servers:  
TCP/IP network  
: Windows NT 4.0, Windows 2000  
: NetWare 3.x, 4.x, or 5.x  
IPX/SPX network  
19  
 
20  
 
SETUP FLOW AND UTILITY  
21  
 
SETUP FLOW CHART  
This chapter describes the procedure and reference of the manuals for each procedure according to  
the operating system and the environment for printing.  
FOR WINDOWS  
For Parallel Connection  
To print with the GA-1140 connected in parallel connection, you can print via LPT1 port.  
Reference Manual  
Setup Flow  
Procedure  
Required utility or item used for the procedure  
Connect the GA-  
1140  
Connect the GA-1140 and  
a computer with a parallel  
cable.  
Administrator's Guide  
M Preparing for GA-1140 Setup  
Connecting to the Parallel Port  
-
Install the Printer  
Driver  
Install the printer driver  
and set up the installable  
options and user informa-  
tion on the printer driver.  
User's Guide  
M Installing User Software on a Windows Computer  
M Installing the Printer Driver  
Installing the Printer Driver for Parallel Printing  
Configuring the Options  
Setting the User Information  
CD-ROM  
22  
 
For SMB Printing  
To print with the GA-1140 connected to a Windows network, you can print by SMB printing.  
Reference Manual  
Setup Flow  
Procedure  
Required utility or item used for the procedure  
Connect the GA-  
1140  
Connect the GA-1140 to  
your network.  
Administrator's Guide  
M Preparing for GA-1140 Setup  
Connecting to the Network  
-
Setup the TCP/IP  
Assign the IP address,  
Subnet Mask, and Gate-  
way address to enable  
TopAccess.  
Administrator's Guide  
M Setting up the Network Setup Options  
M Setting up the Protocols  
Setting up the TCP/IP Options  
Touch Panel Display  
Setup the SMB  
printing  
Enable theWindows Print-  
ing Service and configure  
the network options.  
Administrator's Guide  
M Setting up the Network Setup Options  
M Setting up the Print Services  
Setting up the Windows Printing Service  
TopAccess  
Install the Printer  
Driver  
Install the printer driver  
and set up the installable  
options and user informa-  
tion on the printer driver.  
User's Guide  
M Installing User Software on a Windows Computer  
M Installing the Printer Driver  
Installing the Printer Driver for SMB Printing  
Configuring the Options  
Setting the User Information  
CD-ROM  
23  
 
For LPR Printing  
To print with the GA-1140 connected to a TCP/IP network from the Windows NT 4.0, Windows 2000,  
and Windows XP, you can print using the TCP/IP and LPR connection as well.  
Reference Manual  
Setup Flow  
Procedure  
Required utility or item used for the procedure  
Connect the GA-  
1140  
Connect the GA-1140 to  
your network.  
Administrator's Guide  
M Preparing for GA-1140 Setup  
Connecting to the Network  
-
Setup the TCP/IP  
Assign the IP address,  
Subnet Mask, and Gate-  
way address.  
Administrator's Guide  
M Setting up the Network Setup Options  
M Setting up the Protocols  
Setting up the TCP/IP Options  
Touch Panel Display  
Setup the LPR  
printing  
Enable the LPD Printing  
Service.  
Administrator's Guide  
M Setting up the Network Setup Options  
M Setting up the Print Services  
Setting up the LPD Printing Service  
TopAccess  
Install the Printer  
Driver  
Install the printer driver  
and set up the installable  
options and user informa-  
tion on the printer driver.  
User's Guide  
M Installing User Software on a Windows Computer  
M Installing the Printer Driver  
Installing the Printer Driver for LPR Printing  
Configuring the Options  
Setting the User Information  
CD-ROM  
24  
 
For IPP Printing  
To print with the GA-1140 connected to a TCP/IP network from the Windows 2000 and Windows XP,  
you can print via Internet or Intranet using the IPP connection.  
Reference Manual  
Setup Flow  
Procedure  
Required utility or item used for the procedure  
Connect the GA-  
1140  
Connect the GA-1140 to  
your network.  
Administrator's Guide  
M Preparing for GA-1140 Setup  
Connecting to the Network  
-
Setup the TCP/IP  
Assign the IP address,  
Subnet Mask, and Gate-  
way address.  
Administrator's Guide  
M Setting up the Network Setup Options  
M Setting up the Protocols  
Setting up the TCP/IP Options  
Touch Panel Display  
Install the Printer  
Driver  
Install the printer driver  
and set up the installable  
options and user informa-  
tion on the printer driver.  
User's Guide  
M Installing User Software on a Windows Computer  
M Installing the Printer Driver  
Installing the Printer Driver for IPP Printing  
Configuring the Options  
Setting the User Information  
CD-ROM  
25  
 
For Novell Network  
Where the GA-1140 is connected to a network with Novell network, you can print via a NetWare  
server.  
Reference Manual  
Setup Flow  
Procedure  
Required utility or item used for the procedure  
Connect the GA-  
1140  
Connect the GA-1140 to  
your network.  
Administrator's Guide  
M Preparing for GA-1140 Setup  
Connecting to the Network  
-
Setup the Print  
Server  
Setup the NetWare server.  
Administrator's Guide  
M Setting up the Network Servers  
NetWare Server Setup  
NetWare Server  
Setup the TCP/IP  
Assign the IP address,  
Subnet Mask, and Gate-  
way address to enable  
TopAccess.  
Administrator's Guide  
M Setting up the Network Setup Options  
M Setting up the Protocols  
Setting up the TCP/IP Options  
Touch Panel Display  
Setup the Novell  
Configuration  
Select the frame type.  
Administrator's Guide  
M Setting up the Network Setup Options  
M Setting up the Protocols  
Setting up the IPX/SPX Options  
TopAccess  
Continue to next page.  
26  
 
Continued from previous page.  
Configure the NetWare  
Setup on the GA-1140  
Administrator's Guide  
M Setting up the Network Setup Options  
M Setting up the Print Services  
Setting up the NetWare Options  
TopAccess  
Install the Printer  
Driver  
Install the printer driver  
and set up the installable  
options and user informa-  
tion on the printer driver.  
User's Guide  
M Installing User Software on a Windows Computer  
M Installing the Printer Driver  
Installing the Printer Driver for Novell Printing  
Configuring the Options  
Setting the User Information  
CD-ROM  
27  
 
FOR MACINTOSH  
To print from the Macintosh computer, you can print via the AppleTalk for Ethernet.  
: The PS3 Upgrade (GE-1020) or PS3 Scan & HDD Upgrade (GE-1060+GE-1110) is  
required to use the GA-1140 in the AppleTalk network.  
Reference Manual  
Setup Flow  
Procedure  
Required utility or item used for the procedure  
Connect the GA-  
1140  
Connect the GA-1140 to  
your network.  
Administrator's Guide  
M Preparing for GA-1140 Setup  
Connecting to the Network  
-
Setup the TCP/IP  
Assign the IP address,  
Subnet Mask, and Gate-  
way address to enable  
TopAccess.  
Administrator's Guide  
M Setting up the Network Setup Options  
M Setting up the Protocols  
Setting up the TCP/IP Options  
Touch Panel Display  
Setup the AppleTalk  
Enable the AppleTalk and  
specify the server name  
and AppleTalk zone.  
Administrator's Guide  
M Setting up the Network Setup Options  
M Setting up the Protocols  
Setting up the AppleTalk Options  
TopAccess  
Install the Printer  
Driver  
Install the Adobe PS  
printer driver and PPD file,  
and create a printer.  
User's Guide  
M Installing User Software on a Mac OS Computer  
M Installing the Printer Driver  
Installing the Printer Driver to Mac OS Computer  
28  
CD-ROM  
 
SPECIFICATIONS  
29  
 
SPECIFICATIONS  
PRINTER BOARD  
Item  
Specifications  
Product Name  
CPU  
GA-1140  
Intel Pentium 500MHz  
Memory  
Standard: DIMM 128 Megabytes  
Expansion slot: DIMM  
(Upgradable to 256 Mbyte)  
Print Speed  
Paper Size  
Max. 81 pages/minute  
A3, A4, A5, B4, B5, FOLIO, LEDGER, LEGAL, LETTER, STATEMENT,  
COMPUTER, 13inch LEGAL, 8.5SQ, 8K, 16K  
Conforming to IEEE-P1284 (Standard, Nibble Mode, ECP Mode)  
Data Transfer Speed: 10/100 Mbps  
Connector: 10Base-T/100Base-TX: RJ-45 Connector x 1  
PCL6  
Interface: Parallel  
Interface: NIC  
Emulation  
PCL Fonts  
81 Roman Fonts  
Applicable Computers:  
IBM PC/AT computer and compatible.  
Macintosh computer (when PS3 Upgrade or PS3 Scan & HDD Upgrade is installed.)  
30  
 
OPTIONS  
PS3 Upgrade  
Item  
Specifications  
GE-1020  
PS3  
Product Name  
Emulation  
PS Fonts  
251 Roman Fonts  
PS3 Scan & HDD Upgrade  
Item  
Specifications  
Product Name  
GE-1060  
GE-1060, GE-1110  
Disk Space: 10GB  
Emulation:PS3  
PS Fonts: 136 Roman Fonts  
CD-ROM:Command WorkStation  
E-mail Port Monitor  
Fiery Remote Scan  
GE-1110  
Scan Accelerator Board  
Expansion Memory  
Item  
Specifications  
Product Name  
GC-1080  
128 Mbyte SDRAM, 168-pin DIMM  
Dongle for DocBuilder Pro 1.5  
Item  
Specifications  
GB-1160  
Product Name  
Dongle  
CD-ROM: Adobe Acrobat 4.05  
* This option should be installed with the PS3 Scan & HDD Upgrade (GE-1060, GE-1110).  
31  
 
32  
 
 
1-1, KANDA NISHIKI-CHO, CHIYODA-KU, TOKYO, 101-8442, JAPAN  
Copyright © TOSHIBA TEC CORPORATION 2002  
ALL RIGHTS RESERVED  
6LA50199000  
R02052016900-TTEC  
02-05 TG  
 

Texas Instruments Power Supply ADS5411 User Manual
Turbo Chef Technologies Microwave Oven i3 User Manual
U Line Ice Maker SS1095 User Manual
Uniden Cordless Telephone EXR 2480 User Manual
Uniden Telephone EXP900 User Manual
Universal Remote Control Universal Remote SL 8000 User Manual
Vantec Network Card UGT CR920 User Manual
ViewSonic Projector PJ562 User Manual
Vizio Flat Panel Television E321MV User Manual
VTech Cordless Telephone VT6221 User Manual