Toshiba Flat Panel Television 29CZ5DE User Manual

OWNER'S MANUAL  
Color Television  
Owner's Record  
29CZ5DE  
29CZ6DA  
29CZ6TES  
You will find the model number and serial number on  
the back of the TV. Record these numbers in the spaces  
provided below. Refer to them whenever you call upon  
your TOSHIBA dealer regarding this product.  
Model number:  
Serial number:  
©TOSHIBA CORPORATION, 2005  
All Rights Reserved  
Printed in Indonesia  
23566823  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
1
23/9/05, 9:25 AM  
 
SAFETY INSTRUCTIONS AND MAINTENANCE (continued)  
Notes on installation and on use  
11) Place the TV on a horizontal, stable surface. Avoid location subject to vibration. Do not  
place the TV on its side or back. Otherwise, the TV may drop or fall down which may  
cause injury or damage.  
12) Do not block the ventilation holes. Place the TV at least 10 cm away from the walls for  
good air circulation. The inside of this TV will overheat if the ventilation holes are sealed,  
which may result in a fire.  
13) Take measures to prevent the TV from falling over. If not, the TV may lean or fall over and  
cause an injury. When moving, watch out for the ties.  
14) Avoid placing the TV in direct sunshine, near a heating source or places with a high  
temperature, such as in a closed car. A fire may result when the inside temperature  
increases.  
15) Also avoid the placing the TV on dusty or damp places. This may cause a fire or electric  
shock.  
16) Set up the outdoor antenna away from high ways, power lines and neon signs. If the  
antenna falls down or drops, it may cause injury or electric shock accidents.  
The antenna should be checked and replaced periodically.  
17) Do not jolt the TV, resulting in the TV falling over, dropping or causing an injury.  
18) Keep magnets, electric clocks, speakers, etc. away from the TV.  
19) Do not spray volatile compounds such as insecticide on the cabinet. This may cause a  
discoloration or damage of the cabinet.  
Notes on cleaning  
20) Before cleaning, unplug the power cord.  
Clean the cabinet with a soft and dry cloth.  
Do not use benzine, thinner, etc. to clean the TV.  
21) Sometimes disconnect the power plug from the outlet and check it.  
If dust has collected on the power plug connectors, clean off the dust.  
13)  
12)  
16)  
14)  
Not lean  
and  
protrude  
Sturdy tie  
20)  
21)  
3
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
3
23/9/05, 9:25 AM  
 
TABLE OF CONTENTS  
GETTING STARTED ....................................................................................5  
NAME AND FUNCTIONS OF CONTROLS................................................. 6  
TV Front and Remote control ................................................................6  
MENU FUNCTION .......................................................................................7  
Menu display chart .................................................................................7  
BASIC OPERATIONS ..................................................................................8  
To turn TV on/off.....................................................................................8  
Selecting the channels ...........................................................................8  
Selecting the menu language................................................................8  
To display on-screen information .........................................................8  
To activate Blue screen ..........................................................................8  
PICTURE AND SOUND ADJUSTMENT.....................................................9  
Color and Sound system........................................................................9  
Picture quality adjustment .....................................................................9  
Sound quality adjustment....................................................................10  
Stereo/ Bilingual selection ...................................................................11  
TIMER SETTING ........................................................................................12  
Setting the Timer ..................................................................................12  
CHANNEL PRESET....................................................................................13  
Presetting channel ................................................................................13  
VIEWING TELETEXT .................................................................................15  
Teletext control functions ....................................................................15  
Fast / List Mode .....................................................................................16  
Double Window Teletext......................................................................17  
EXTERNAL EQUIPMENT CONNECTIONS .............................................18  
TROUBLESHOOTING................................................................................19  
SPECIFICATIONS ........................................................................ Back Cover  
Exemptions  
9 Toshiba is not liable for any damage caused by natural disaster (such as thunder,  
earthquake),fire, acts by third parties, accidents, misuse, or uses in other improper  
conditions.  
9 Toshiba is not liable for incidental damages (such as profit loss or interruption in business,  
modification or erasure of record data, etc.) caused by use or inability to use of product.  
9 Toshiba is not liable for any damage caused by neglect of the instructions described in the  
owner’s manual.  
9 Toshiba is not liable for any damage caused by misuse or malfunction through simultaneous  
use of this product and the connected equipment.  
4
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
4
23/9/05, 9:25 AM  
 
GETTING STARTED  
Connect the antenna to  
rear of the TV.  
at the  
Push the (Power switch) until it  
clicks to turn on the power.  
Refer to page 8 for details on power on and off.  
1
4
UHF  
VHF  
Outdoor  
antenna  
75-ohm coaxial cable  
Preset the channels automatically  
(ASM function).  
Use remote control for this operation. The  
buttons on the TV with similar name may also  
be use.  
or  
5
Mixer  
300-ohm twin-lead feeder with  
optional antenna adapter  
Connect the power cord to an  
electrical outlet with standard  
household power within the range  
of ~110-240V, 50/60Hz.  
1
Select the starting position for channel  
to be preset. Press the Number buttons  
(-/--, 0~9) or CH s/t.  
2
1
Notes  
Do not connect the power cord until all  
your equipments have been connected.  
The antenna cables should not be  
bundled with the power cord and the like.  
2
Set the correct broadcast system for  
your region. Press MENU and then ;-/+  
to highlight the SET UPicon.  
SETUP  
ENGLISH  
Insert the batteries into the remote  
control.  
LANGUAGE  
COLOR MODE  
SOUND MODE  
SKIP  
AUTO  
B/G  
3
OFF  
BLUE SCREEN  
TEXT  
ON  
FAST  
Operating range  
MENU  
SELECT  
/
MENU /+  
BACK  
Confirm COLOR MODEis set to AUTO”  
and SOUND MODEis set to proper  
system. (Refer to the table on page 9.) If  
not, press CH s/t to select COLOR  
MODEor SOUND MODE, press ;-/+  
and then CH s/t to set each proper  
system.  
5m  
Remote sensor  
Requires two R03  
(AAA) batteries  
If the remote control does not operate  
correctly, if the operating range becomes  
reduced, replace both batteries with  
new ones.  
When the remote control will not used for  
a long period of time or when the batteries  
are worn out, remove the batteries to  
prevent leakage.  
3
Press MENU and then ;-/+ to highlight  
the TUNINGicon. Select ASM,  
then press ;+ to start the search. When  
the TV screen returns to the start position,  
the procedure is complete.  
TUNING  
CH  
MFT  
AFT  
OFF  
Do not drop, dampen or disassemble the  
remote control.  
ASM  
CH  
SEARCH  
POSITION  
MEMORY  
P001  
Cautions  
MENU  
SELECT  
/
ADJUST /+  
BACK  
Do not dispose batteries into fire. Dispose  
batteries into the designated disposal areas  
according to the local regulations.  
Do not mix battery types or combine used  
batteries with new ones.  
Press ;-/+ to adjust the sound  
volume.  
6
5
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
5
23/9/05, 9:26 AM  
 
NAMES AND FUNCTIONS OF CONTROLS  
For details on the use of each control, refer to the page numbers in [ ] brackets.  
TV Front and Remote control  
!
"
1
2
3
4
5
6
#
$
Open the lid  
%
&
(
7
8
9
j
i
d e  
g
b c  
a
h
f
TV  
Remote Control  
a
b
c
q
Main power on/off [8]  
Remote sensor [5]  
1
2
f
Power on/standby [8]  
0
mI/II Stereo/bilingual  
selection [11]  
o
Sound Mute, press  
again or ;-/+ to  
restore the sound.  
Only available for  
29CZ5DE and 29CZ6DA.  
q
r
Power indicator (red) [8]  
Timer-ON indicator  
(green) [12]  
-
Double-window on/off  
[17]  
3
4
0~9 Number buttons [8]  
a
Input source selection  
[18],  
Timer-ON position  
d MENU Turn on menu display  
=
~
-/-- Digit selection [8]  
[7]  
;-/+ Volume down/up [5],  
Menu selection or  
e a Input source selection  
setting [12]  
[18]  
Switch the active  
teletext page of the  
double window mode  
[17]  
item adjust [7]  
f - ;+ Volume down/up [5],  
Menu selection or item  
adjust [7]  
!
@
Picture menu [9]  
TXT/TV Teletext/TV selection  
[15]  
g tcs Channel down/up [8],  
5
6
MENU Turn on menu display  
[7]  
Menu item selection  
[7]  
#
Teletext functions [15]  
y/X Time display, To select  
a page while viewing a  
normal picture  
CH s/t Channel up/down [8],  
h
L
Stereo headphones jack  
(Ø3.5mm) for private  
listening. The sound  
from the speakers will  
be cut off automatically.  
Menu item selection [7]  
7
8
8
Sound menu [10]  
^
?
v
To enlarge teletext  
display size  
CALL/i On-screen on/off [8],  
Turn off the menu [8],  
Teletext initial/index [15]  
To reveal concealed  
text  
i
j
AUDIO Audio input terminals  
[18]  
9
Teletext colored buttons  
Red/Green/Yellow/Blue  
[16]  
To hold a wanted page  
VIDEO Video input terminal  
[18]  
Note: The shaded button is not available for 29CZ6TES. If you press the button, MODE NOT  
AVAILABLEwill appear on the screen.  
6
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
6
23/9/05, 9:26 AM  
 
MENU FUNCTION  
Before watching the TV, please familiarize yourself the method to use the menu function of  
this TV.  
Instructions in this manual are based on using the remote control.  
Press the MENU to display menu, then press the ;-/+ to select menu.  
Press the CH s/tto select an item and then press the ;-/+ to select or adjust setting.  
This manual shows the On-Screen Display of 29CZ5DE model.  
Menu display chart  
PICTURE  
MODE  
PICTURE  
MODE  
DYNAMIC  
DYNAMIC  
100  
50  
100  
50  
CONTRAST  
CONTRAST  
BRIGHTNESS  
COLOR  
BRIGHTNESS  
COLOR  
50  
50  
00  
00  
00  
TINT  
TINT  
00  
SHARPNESS  
SHARPNESS  
ON  
ON  
100  
INTELLIGENT PICTURE  
INTELLIGENT PICTURE  
CONTRAST  
MENU  
BACK  
MENU  
MENU  
SELECT  
/
MENU /+  
BACK  
SELECT  
/
ADJUST /+  
BACK  
SOUND  
SOUND  
MEMORY  
MEMORY  
MODE  
MODE  
00  
00  
00  
00  
00  
00  
BASS  
BASS  
TREBLE  
TREBLE  
BALANCE  
EQUALIZER  
MTS MODE  
BALANCE  
EQUALIZER  
MTS MODE  
(
+
)
AUTO  
AUTO  
00  
BASS  
ON  
ON  
INTELLIGENT SOUND  
INTELLIGENT SOUND  
MENU  
BACK  
MENU  
MENU  
SELECT  
/
MENU /+  
BACK  
SELECT  
/
ADJUST /+  
BACK  
TIMER  
TIMER  
TIMER OFF  
TIMER ON  
00:00  
00:00  
TIMER OFF  
TIMER ON  
00:00  
00:53  
P001  
P001  
MENU  
MENU  
SELECT  
/
MENU /+  
BACK  
SELECT  
/
ADJUST /+  
BACK  
SETUP  
SETUP  
ENGLISH  
AUTO  
B/G  
ENGLISH  
AUTO  
B/G  
LANGUAGE  
COLOR MODE  
SOUND MODE  
SKIP  
LANGUAGE  
COLOR MODE  
SOUND MODE  
SKIP  
OFF  
OFF  
BLUE SCREEN  
TEXT  
BLUE SCREEN  
TEXT  
ON  
ON  
FAST  
FAST  
MENU  
MENU  
SELECT  
/
MENU /+  
BACK  
SELECT  
/
ADJUST /+  
BACK  
TUNING  
TUNING  
MFT  
MFT  
AFT  
OFF  
AFT  
OFF  
ASM  
ASM  
SEARCH  
POSITION  
MEMORY  
SEARCH  
POSITION  
MEMORY  
P002  
BACK  
P002  
SEARCH  
VHF  
L
P002  
STOP  
MENU  
MENU  
SELECT  
/
MENU /+  
SELECT  
/
ADJUST /+  
BACK  
Notes  
If you do not make a selection within 15 seconds, the menu display disappears automatically.  
To return to the previous menu, press MENU.  
The  
input source is selected.  
MTS MODE will not display on the SOUND menu for 29CZ6TES model.  
area on the SOUND, SET UP and TUNING menu display does not appear when video  
7
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
7
23/9/05, 9:27 AM  
 
BASIC OPERATIONS  
To turn TV on/off  
Selecting the menu language  
Choose from five different languages (English,  
Mandarin, Malay, Vietnamese and Thai), select  
to display all on-screen Menus in your language  
of choice.  
1
2
Press the q power switch on the TV. The q  
red power indicator lights up.  
If no picture appears, it is in the standby mode,  
press the f button on the remote control.  
1
Press MENU and then ;-/+ to highlight the  
Notes  
SETUPicon.  
You can also turn on the TV by pressing  
one of the Number buttons (0~9) on the  
2
Press CH s/t to select LANGUAGE, then  
press ;-/+ to enter to LANGUAGE menu  
mode.  
remote control instead of the f button.  
By pressing the number (one digit only)  
where the channel you want to watch is  
preset, you can turn on the TV and  
channel selection at the same time.  
3
Press CH s/tand then ;-/+ to select the  
desired language.  
SETUP  
LANGUAGE  
ENGLISH  
When the remote control is not at hand,  
you can turn on the TV by pressing the  
a, -;+ or tcsbutton on the TV.  
LANGUAGE  
COLOR MODE  
SOUND MODE  
SKIP  
ENGLISH  
AUTO  
D/K  
MELAYU  
OFF  
BLUE SCREEN  
TEXT  
ON  
FAST  
3
4
To switch to the standby mode, press the  
MENU  
MENU  
SELECT  
/
ADJUST /+  
BACK  
SELECT  
/
ADJUST /+  
BACK  
f button.  
To turn off the main power, press the q  
power switch.  
To display on-screen information  
Press CALL/i to display the position number  
or video input mode selected (A1, A2, DVD  
or A3) and the Mono/Stereo/Bilingual*  
audio status. To erase the display, press  
CALL/iagain.  
Auto Power Off  
The TV will automatically turn itself off after  
about 15 minutes if it is tuned to a vacant  
channel, TV broadcasts for a day are finished,  
or the signal is interrupted for any reason. This  
feature does not work in video input mode.  
Position number or  
video input mode  
25  
Mono/Stereo/Bilingual  
audio status*  
Selecting the channels  
Press the -/-- button to select the input digit  
of position number and then press 0~9 to  
select the number. (e.g., for 25, press -/-- to  
display --, then 2 and 5)  
(*Mono/Stereo/Bilingual symbol only appears  
on 29CZ5DE and 29CZ6DA model)  
The CALL/ibutton can also be used to erase  
the on-screen menu display.  
--  
25  
To activate Blue screen  
Press tto select lower position number, sto With the blue screen function ON, the TV screen  
select higher ones.  
will automatically turn blue and the sound will  
be muted when no TV signal is received.  
Note  
1
Press MENU and then ;-/+ to highlight  
When a TV channel with teletext service is  
selected, a black bar with channel indication will  
display on the screen for a second. However,  
abnormal indication may appear depending on  
the received signal. This is not a malfunction of  
the TV.  
the SETUPicon.  
2
Press CH s/t to select BLUE SCREEN,  
then press ;-/+ to set ON or OFF.  
8
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
8
23/9/05, 9:27 AM  
 
PICTURE AND SOUND ADJUSTMENT  
Color and Sound system  
Picture quality adjustment  
If the color or sound of a certain channel  
is abnormal  
To access the  
PICTURE menu  
Press  
for direct selection or press MENU and  
Thecolor orsoundsystemsettingmaybeincorrect.  
then ;-/+ to highlight the PICTUREicon.  
Press MENU and then ;-/+ to highlight the  
SETUPicon.  
PICTURE  
DYNAMIC  
MODE  
100  
50  
CONTRAST  
BRIGHTNESS  
COLOR  
SETUP  
50  
00  
ENGLISH  
AUTO  
D/K  
TINT  
LANGUAGE  
00  
SHARPNESS  
COLOR MODE  
SOUND MODE  
SKIP  
ON  
INTELLIGENT PICTURE  
OFF  
ON  
MENU  
SELECT  
/
MENU /+  
BACK  
BLUE SCREEN  
TEXT  
FAST  
MENU  
SELECT  
/
MENU /+  
BACK  
Press CH s/tto select the following items:  
Press CH s/tto select the following items:  
MODE (Preset picture mode)  
Four preset picture modes can be selected.  
COLOR MODE system setting  
Press ;-/+ to enter COLOR MODE selection.  
Press CH s/t and then ;-/+ to select the  
appropriate color system. AUTO, PAL, SECAM,  
NTSC4.43 or NTSC3.58 can be selected.  
Press ;-/+ to enter MODE selection. Press  
CH s/t and then ;-/+ to select the desired  
picture mode.  
DYNAMIC  
select for a bright and dynamic  
picture  
SOUND MODE system setting  
If the picture or sound is abnormal when  
STANDARD select for standard picture  
settings  
receiving programs through the  
(antenna)  
terminal, the sound system setting may be  
incorrect. Press ;-/+ to enter SOUND MODE  
selection. Press CH s/t and then ;-/+ to  
select the appropriate sound system according  
to the broadcast system of your region.  
Refer to the table below. B/G, I, D/K or M can  
be selected.  
MILD  
select to display a softer picture  
MEMORY  
select for a picture quality set  
according to your preferences  
Broadcast Transmission Systems in Each Country or Region  
System  
Sound  
Area  
Country or Region  
Color  
Bahrain, Kuwait, Israel, Oman, Qatar, United Arab  
Emirates, Yemen, and other middle Eastern countries.  
Indonesia, Malaysia, Singapore, Thailand, and other  
Southeast Asian Countries.  
PAL  
B/G  
Asia  
M. E.  
China  
China Hong Kong  
PAL  
PAL  
D/K  
I
Iraq, Islamic Republic of Iran, Lebanon, Saudi Arabia  
Russian Federation  
Myanmar  
SECAM  
SECAM  
NTSC  
PAL  
PAL  
PAL  
B/G  
D/K  
M
B/G  
I
N
M
M
Oceania Australia, New Zealand  
Africa  
Republic of South Africa  
Argentina, Paraguay, Uruguay  
Brazil  
South  
America  
PAL  
NTSC  
Chile, Colombia  
9
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
9
23/9/05, 9:27 AM  
 
PICTURE AND SOUND ADJUSTMENT (continued)  
CONTRAST Adjust to increase or decrease  
Sound quality adjustment  
To access the SOUND menu  
the picture contrast with + or -  
respectively.  
Press 8for direct selection or press MENU and  
then ;-/+ to highlight the SOUNDicon.  
BRIGHTNESS Adjust to brighten or  
darken the picture with + or -  
respectively.  
SOUND  
COLOR  
TINT  
Adjust to increase or decrease  
the color intensity with + or -  
respectively.  
MEMORY  
MODE  
00  
00  
00  
BASS  
TREBLE  
BALANCE  
EQUALIZER  
MTS MODE  
AUTO  
ON  
INTELLIGENT SOUND  
Adjust the picture to be more  
greenish or more purplish  
with + or - respectively. This  
effect is provided for NTSC  
system only.  
MENU  
SELECT  
/
MENU /+  
BACK  
Press CH s/tto select the following items:  
MODE (Preset sound mode)  
Three preset sound modes can be selected.  
SHARPNESS Adjust to sharpen or soften the  
picture with + or - respectively.  
Press ;-/+ to enter MODE selection. Press  
CH s/t and then ;-/+ to select desired  
sound mode.  
INTELLIGENT PICTURE  
The Intelligent picture mode  
equipped with Black/White/  
Blue stretch feature. It enable  
a maximum of visible details  
in the darker parts of the  
picture and over the whole  
range of luminance. A brighter  
and sharper impression of the  
picture is percepted.  
THEATER  
select for playing music and  
movie  
NEWS  
select to emphasize human voice  
MEMORY  
select for a sound quality set  
according to your preferences  
BASS  
Adjust to increase or decrease  
lower-pitched sound with  
+ or - respectively.  
Press ;-/+ to set ONor  
OFF.  
TREBLE  
Adjust to increase or decrease  
higher-pitched sound with  
+ or - respectively.  
Notes  
Any adjustment of the BRIGHTNESS,  
CONTRAST, COLOR, TINT or SHARPNESS  
settings will be stored in the MEMORY mode.  
BALANCE Adjust to decrease left or right  
speaker balance with + or -  
If you adjust any one of items: BRIGHTNESS,  
CONTRAST, COLOR, TINT or SHARPNESS in  
the DYNAMIC, STANDARD or MILD modes,  
the TV will automatically change to the  
MEMORY mode.  
respectively. This adjusted  
condition is not stored in the  
Memory mode.  
EQUALIZER Press ;-/+ to enter EQUALIZER  
menu mode. A total of 5  
equalizer bands can be adjusted  
according to your preference.  
EQUALIZER  
00 DB  
00 DB  
+02 DB  
00 DB  
00 DB  
100HZ  
300HZ  
1KHZ  
3KHZ  
8KHZ  
MENU  
SELECT  
/
ADJUST /+  
BACK  
10  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
10  
23/9/05, 9:27 AM  
 
PICTURE AND SOUND ADJUSTMENT (continued)  
Press CH s/t to select the  
desired band and then press ;  
-/+ to adjust the level.  
Stereo/ Bilingual selection  
(Only available for 29CZ5DE/29CZ6DA model)  
To select the stereo programs  
MTS MODE (Multi-channel TV Sound)  
Only available for 29CZ5DE/29CZ6DA model  
1
When a stereo program is received, M  
appears on the screen.  
The TV receives both stereo and bilingual  
broadcasts transmitted in either the NICAM  
or German stereo/bilingual broadcast system.  
2
Press mI/II to select the stereo/monaural  
mode. M and U appear cyclically on  
the screen.  
Press ;-/+ to select AUTOor MONO.  
AUTO  
The AUTOsetting of the  
MTS mode automatically  
recognize stereo/bilingual  
programs depending on the  
broadcast signal.  
MONO  
If you experience noise or poor  
reception of any stereo/  
bilingual program, set the MTS  
MODE to MONO. Noise will  
be reduced and reception may  
improve.  
Display  
M
Reception mode  
Stereo  
Monarual  
U
Note  
INTELLIGENT SOUND  
The Intelligent sound mode  
If you experience noise with a particular  
program on whose channel reception is usually  
good, try setting MTS MODE to AUTO, then  
switch the mI/II button to U(monaural).  
equipped with Automatic  
Volume Levelling (AVL) and  
Extended Spatial Stereo (ESS)  
feature. It stabilize the volume  
to prevent any sudden  
loudness occured. And also  
provides user an experience of  
expanded stereo image by  
widening stereo sound effects.  
To select the bilingual programs  
1
When a bilingual program is received, I/II  
appears on the screen.  
2
Press mI/II to select the sound to be  
heard. The sound differs according to the  
transmission system: NICAM or German  
stereo/bilingual broadcast. I, II and U  
appear cyclically on the screen.  
Press ;-/+ to set ONor  
OFF.  
Notes  
Any adjustment of the BASS, TREBLE or  
EQUALIZER settings will be stored in the  
MEMORY mode.  
Sound to be heard  
Display  
German stereo/  
NICAM  
bilingual broadcast  
If you adjust any one of items: BASS, TREBLE  
or EQUALIZER in the THEATER or NEWS  
modes, the TV will automatically change to  
the MEMORY mode.  
I
Sub I sound Main sound  
Sub II sound Sub sound  
Main sound Main sound  
II  
U
When the volume is set above 80, it is not  
recommended to adjust the bass, treble or  
equalizer to a high value.  
11  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
11  
23/9/05, 9:27 AM  
 
TIMER SETTING  
TIMER ON  
Setting the Timer  
With the TIMER ON set, the TV will automati-  
cally turn on to a preset channel at a preset time.  
To access the TIMER menu  
Press MENU and then ;-/+ to highlight the  
To set the TIMER ON  
TIMERicon.  
Highlight the TIMER ON, press ;-/+ to set  
after how many hours and minutes you want  
the TV to turn on. The setting method will be  
similar to the TIMER OFF.  
TIMER  
TIMER OFF  
00:00  
00:00  
TIMER ON  
P001  
The Ytimer-ON indicator (green) will light up.  
Press a to highlight the position number,  
P***. Then, press ;-/+ to set the position  
number.  
MENU  
SELECT  
/
MENU /+  
BACK  
Press CH s/t to select the required timer  
mode (TIMER OFF or TIMER ON). Complete  
the following steps to set the effective time.  
TIMER  
TIMER OFF  
TIMER ON  
00:00  
00:53  
P001  
TIMER OFF  
With the TIMER OFF set, the TV will automa-  
tically switch to standby mode at a preset time.  
MENU  
SELECT  
/
ADJUST /+  
BACK  
To set the TIMER OFF  
When you ;-/+ Setting position  
Highlight the TIMER OFF, press ;-/+ to set after  
how many hours and minutes you want the TV  
to switch into standby mode.  
number is  
;+ increased by 1  
press once  
;-  
decreased by 1  
When you ;-/+  
Setting time is  
;+ increased by 10  
hold down  
;+ increased by 1 minute  
;- decreased by 1 minute  
;+ increased by 30 minutes  
;- decreased by 30 minutes  
;-  
decreased by 10  
press once  
hold down  
Press f to switch the TV to standby mode.  
At the preset time, the TV will turn on  
automatically.  
To cancel the TIMER OFF  
Press ftwice (to turn off the TV once and turn  
it on again) or set the TIMER OFF time to 00:00.  
To cancel the TIMER ON  
Press the q power switch to turn off the TV or  
set the TIMER ON time to 00:00.  
12  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
12  
23/9/05, 9:27 AM  
 
CHANNEL PRESET  
4
Press CH s/t to select MEMORY, then  
press ;+ to memorize the channel at the  
current position.  
Presetting channel  
First, use the ASM (Automatic Search  
Memory) function to preset all active  
channels in your area automatically. Refer to  
step 5 of GETTING STARTED, page 5.  
Then, arrange the preset channels with the  
SEARCH, SKIP and MFT (Manual Fine Tuning)  
functions so that you can tune into only  
desired channels.  
TUNING  
MFT  
AFT  
OFF  
ASM  
SEARCH  
POSITION  
MEMORY  
P002  
MENU  
SELECT  
/
ADJUST /+  
BACK  
Use the SEARCH function if desired channels  
cannot be preset with the ASM or if you would  
like to preset channels to specific position  
numbers one by one.  
5
When you program other channels, repeat  
steps 2 to 4.  
To skip a position number  
To use the SEARCH function  
After presetting the channels, you may skip  
unnecessary position numbers so that only  
the channels you want to watch are selected  
using CH s/t.  
1
Press MENU and then ; -/+ to highlight  
the TUNINGicon.  
1
First, select the position number to be  
skipped with CH s/tor digit selection and  
number buttons (-/--, 0~9).  
TUNING  
MFT  
AFT  
ON  
ASM  
SEARCH  
POSITION  
MEMORY  
P001  
2
Highlight the SET UPicon and press  
CH s/tto select SKIP.  
MENU  
SELECT  
/
MENU /+  
BACK  
2
Press CH s/t to select SEARCH. Press  
-/+ to start searching. Pressing “–”  
;
SETUP  
ENGLISH  
AUTO  
B/G  
LANGUAGE  
COLOR MODE  
SOUND MODE  
SKIP  
searches for channels at lower frequencies  
while pressing +searches for channels at  
higher frequencies. While searching,  
pressing the opposite direction button, + and  
- respectively, will cancel SEARCH function.  
ON  
BLUE SCREEN  
TEXT  
ON  
FAST  
MENU  
SELECT  
/
ADJUST /+  
BACK  
3
Press ;-/+ to set SKIPto ON. This  
completes the setting for skipping the  
selected position number.  
TUNING  
MFT  
AFT  
ON  
ASM  
SEARCH  
POSITION  
MEMORY  
P001  
SEARCH  
VHF  
H
P001  
STOP  
MENU  
SELECT  
/
ADJUST /+  
BACK  
Repeat this process until you can get the  
desired channel.  
3
When the desired channel is shown, press  
CH t to select POSITION. Press ;-/+  
repeatedly until the position number to be  
preset is shown.  
TUNING  
MFT  
AFT  
OFF  
ASM  
SEARCH  
POSITION  
MEMORY  
P002  
MENU  
SELECT  
/
ADJUST /+  
BACK  
13  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
13  
23/9/05, 9:27 AM  
 
CHANNEL PRESET (continued)  
Notes  
Auto fine tuning (AFT)  
When SKIPis set to ONfor the selected  
position number, a * mark appears to the  
left of the position number.  
If the signal frequency is unstable due to  
environmental conditions, use auto fine tuning.  
1
Select the position number where the  
channel you want to fine-tune with CH s/t  
or the digit selection and number (-/--, 0~9)  
buttons.  
12  
Note  
When the position is set to AFT OFF”  
status, the Rmark appears to the left of  
the position number.  
The position number will then be skipped  
when you select the position with CH s/t.  
If you want to restore a skipped position  
number, select it using the -/-- and 0~9 buttons  
then switch the SKIPsetting to OFF.  
25  
Manual fine tuning (MFT)  
The adjustments below are not necessary  
under normal conditions. However, under  
some reception conditions, fine tuning may  
be necessary to improve the picture quality.  
In such cases, adjust the manual fine tuning  
(MFT).  
When the channel is set to AFT ON”  
status, the position number is displayed  
without the Rmark.  
2
3
Press MENU then ;-/+ to highlight the  
TUNINGicon.  
1
Select the position number where the  
channel you want to fine-tune with CH s/t  
or digit selection and number buttons  
(-/--, 0~9).  
Press CH s/tto select AFT. Press ;-/+  
to select the ONindication.  
TUNING  
MFT  
2
3
Press MENU and then ; -/+ to highlight  
AFT  
OFF  
the TUNINGicon.  
ASM  
SEARCH  
POSITION  
MEMORY  
P002  
Press CH s/tto select MFT. Press ; -/+  
to start fine tuning. Press ; -/+ repeatedly  
until the best possible picture and sound  
are obtained.  
MENU  
SELECT  
/
ADJUST /+  
BACK  
Notes  
When you operate MFT, AFT is switched OFF”  
automatically. If you switch on AFT after fine  
tuning with MFT, MFT may be canceled.  
TUNING  
MFT  
AFT  
ON  
ASM  
SEARCH  
POSITION  
MEMORY  
P002  
AFT may be set independently for each  
position.  
MENU  
SELECT  
/
ADJUST /+  
BACK  
14  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
14  
23/9/05, 9:28 AM  
 
VIEWING TELETEXT  
The TV is capable of showing both normal text To enlarge the text display size (^)  
and the text information selected by FAST mode Press ^once to enlarge the top half of the page.  
and LIST mode. The Teletext buttons on the Press again to enlarge the bottom half of the  
remote control have the same function for both page, and again to return to the normal (full)  
text information types.  
size.  
Note  
When viewing the enlarged format teletext page  
with sub pages changes automatically, the top  
half of the page is always displayed first; thus  
disturb the flow of text.  
Press vstop button to hold the sub page while  
viewing the enlarged teletext.  
To display a page of text  
1
Select a position number preset a TV  
channel with the text service desired.  
2
3
Press TXT/TV. The index page will appear.  
Enter the 3-digit page number using the  
Number buttons (0-9). Ex. Page 110:  
Press 1, 1 and 0.  
To select a page while viewing a TV picture  
(y/X)  
When in teletext mode, if a page selection is  
made and then y/X is pressed, a normal  
picture will be displayed. The TV will indicate  
when the page is present by displaying the  
number of the text page at the top of the screen.  
Press TXT/TV to view the page.  
Broadcast station information  
Selected page  
Running clock  
100 100 TELETEXT 11:00:18  
To display news flashes (y/X)  
TELETEXT  
To view news flashes as they are broadcast,  
select the news flash page for the particular  
teletext service (see the index page of teletext  
service). The news flashes will be displayed as  
and when they are broadcast. Press y/Xto  
cancel the news flash display.  
Teletext control functions  
To superimpose the text over a normal broadcast  
picture (TXT/TV)  
Press TXT/TV again.  
Note  
Press TXT/TV to cancel the news flash page  
before changing channels.  
To return to the normal TV mode (TXT/TV)  
Press TXT/TV repeatedly until the text  
disappears.  
To display the time (y/X) (with the teletext  
service only)  
To display an index/initial page (CALL/i)  
Press CALL/i if no page number is displayed  
in the text mode. The index page (FAST mode)  
or the preset initial page (LIST mode) will  
appear.  
To display the accurate time on the screen while  
watching a normal TV picture, press y/X.  
Press again to turn off the time display.  
To reveal concealed text (?)  
Some pages have sections that are concealed,  
such as the answers to quizzes and the  
punchlines of jokes. To see the concealed part,  
press ?. Press ?again to conceal.  
To go to the previous or next page (CH s/t)  
Press CH sto switch to the next page.  
Press CH tto switch to the previous page.  
To stop a page of text (v)  
To adjust MFT in teletext mode  
When a page is divided into sub pages, it is  
convenient to hold a given page.  
Press v to stop the page. vwill appear in  
the top left of the screen.  
During teletext mode, when the teletext or  
picture reception is poor, MFT adjustment is  
possible. Press MENU, MFT+will display on  
the bottom left of the screen. Press ;-/+  
repeatedly to adjust until the best possible text  
and picture are obtain.  
Press again to release the stop mode.  
15  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
15  
23/9/05, 9:28 AM  
 
VIEWING TELETEXT (continued)  
3
Press the colored button which corresponds  
to your desired topic.  
The screen will switch to the selected page.  
Repeat step 3 to switch to the next topic  
you want to view.  
Fast / List Mode  
FAST mode is a method of viewing Teletext  
pages by related subjects grouped by the  
broadcast studio. You can access any given  
topic shown on the screen simply by pressing  
the corresponding colored button on the  
remote control.  
LIST mode is provided for easier operation  
for normal text broadcast. By presetting up to  
four of the most frequently used text pages,  
you can access these pages easily with single  
button operation. The first of these four pages  
is set as the initial page. Each time you select  
the teletext mode, this page appears.  
4
To return to the normal TV mode  
Press TXT/TV twice.  
To display an index page  
Press CALL/i.  
To select the LIST mode  
1
Press MENU and then ;-/+ to highlight  
the SET UPicon.  
Press CH s/tto select TEXT. Then, press  
;-/+ to set TEXTto LIST(LIST mode).  
2
To select the FAST mode  
To preset an initial page  
When you select the FAST mode, four colored  
prompts will appear at the bottom of the  
screen. The colors correspond to those of  
the teletext colored buttons on the remote  
control. So, press the corresponding teletext  
colored button to go to the desired topic  
page instantly.  
1
Select a position number preset a TV  
channel with the normal TEXT service.  
Press TXT/TV to select the text mode.  
Four colored prompts will blink at the  
bottom of the screen.  
2
100 100 TELETEXT 11:00:18  
1
Press MENU and then ;-/+ to highlight  
the SET UPicon.  
Prompts  
100 200 300 400  
SETUP  
ENGLISH  
AUTO  
D/K  
LANGUAGE  
COLOR MODE  
SOUND MODE  
SKIP  
Green  
Yellow  
Blue  
Red  
OFF  
ON  
BLUE SCREEN  
TEXT  
FAST  
3
Press the number buttons to enter the 3-digit  
page number that you want to preset as an  
initial page. Ex. page 120: Press 1, 2 and 0.  
Red prompt will stop blinking at the bottom  
left of the screen. And the preset page  
displays on the screen. (When a vacant  
teletext page is preset, the prompt will not  
stop blinking.)  
MENU  
SELECT  
/
MENU /+  
BACK  
2
Press CH s/tto select TEXT. Then, press  
;-/+ to set TEXTto FAST(Fastext  
mode).  
To view Fastext  
1
Select a position number preset a TV  
channel with the desired FASTEXT service.  
Press TXT/TV to select the text mode. Four  
colored prompts will appear at the bottom  
of the screen.  
120 120 TELETEXT 11:00:18  
2
100 100 TELETEXT 11:00:18  
120 200 300 400  
4
Press the red colored button momently.  
Four colored prompts will turn to white  
momentarily and will be stored in memory.  
Prompts  
Green  
Yellow  
Blue  
Red  
16  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
16  
23/9/05, 9:28 AM  
 
VIEWING TELETEXT (continued)  
To preset desired pages  
To switch the active page  
Press a. The running time clock on the top  
1
Press the green colored button.  
2
Enter the 3-digit page number you want to shows the active page.  
preset by using the number buttons.  
To view a normal broadcast picture and a text  
page simultaneously  
250 250 TELETEXT 11:00:18  
Press  
. A compressed version of the  
broadcast picture is shown on the left side of  
the screen while the active teletext page is on  
the right.  
120 250 300 400  
101 101 TELETEXT 11:00:18  
3
4
Repeat steps 1 and 2 to preset other two  
pages by using the yellow and blue colored  
buttons.  
Press the blue colored button momently.  
Four colored prompts will turn to white  
momentarily and will be stored in memory.  
TELETEXT  
Press  
again. The left half portion of the  
To display a desired page  
Press the desired colored button according to  
the four colored prompts on the screen.  
normal picture is shown on the left side of the  
screen while the active teletext page is on  
the right.  
To display an initial page  
Press CALL/i.  
101 101 TELETEXT 11:00:18  
Note  
You cannot preset the same teletext page  
twice.  
When a vacant teletext page is preset, the  
colored prompt will be blink.  
TELETEXT  
To return to single teletext window, press  
again.  
Double Window Teletext  
Double window feature allow us to view two  
text pages of the same broadcast station at a  
time ,or to view a normal broadcast picture and  
a text page simultaneously.  
To activate Double Window  
During teletext mode, press  
once.  
Two teletext pages appear side by side on the  
screen. Only one page is in active mode. All the  
teletext operation can be done on the active  
page. The other page is for viewing only.  
101 101 TELETEXT  
100 100 TELETEXT 11:00:18  
TELETEXT  
TELETEXT  
17  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
17  
23/9/05, 9:28 AM  
 
EXTERNAL EQUIPMENT CONNECTIONS  
You can connect video equipments such as a VTR and video camera to this TV and enjoy the  
high quality picture. The front A/V terminal a(3) is convenient when hooking up video camera  
or game equipment.  
The following describes how to use and connect the TV with other AV equipment. Refer to the  
owners manual of the equipment to be connected as well.  
If your video equipment has an S-VIDEO output terminal, connect it to the S-VIDEO a (1) input  
terminal (special S-VIDEO type) of the TV. If not, connect it to the video terminal (phono type).  
Connection cables are not supplied.  
Caution: Do not plug in any power cords until you have finished connecting all equipment.  
Video camera  
To  
antenna  
output  
To video  
output  
VTR  
To audio  
outputs  
Y
W
R
Y
W
R
: Signal flow  
Y
W
R
: yellow (video/Y)  
: white (audio L/MONO)  
1
2
Y
W
R
Back  
: red (audio R, PR/CR  
: blue (PB/CB  
)
B
)
VTR for recording  
DVD (or another VTR)  
COMPONENT  
AUDIO  
VIDEO OUTPUTS  
OUTPUTS  
Y
W
R
W
Y
B
R
R
Y
PB/CB PR/CR L/MONO  
R
Notes  
The > MONITOR terminals output the TV  
program or video (A1, A2/DVD, A3) signals  
being displayed on the screen.You can record  
a TV program or video signals by connecting a  
VTR from the output terminals (>MONITOR)  
to the input terminals of the VTR. However,  
except for personal use, you are not allowed  
to use video or sound you have recorded  
without consent of the owner of copyright  
according to copyright law.  
When playing back DVD images by connecting  
to COMPONENT VIDEO INPUT, the (>  
MONITOR) video terminal will output Y”  
(Black and White) signal only. In such condition,  
abnormal images will occur if recorded.  
Do not connect one VTR to the output and  
input terminals on the TV simultaneously, it  
may cause interference.  
Your DVD video player should have either the  
B
R
B
R
P , P or C , C output terminals. This TV is  
available for either type.  
* Connect either the S-VIDEO terminal or the  
VIDEO terminal of the input terminals a(1).  
If you use both terminals at the same time,  
unusual phenomena may happen to the TV  
set and/or VTR.  
To select the video input source  
Each time you press a, the A1mark,A2”  
mark (or DVDmark when there is a DVD  
B
B
P /C input), A3mark, and channel position  
number appear and selected cyclically.  
18  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
18  
23/9/05, 9:28 AM  
 
TROUBLESHOOTING  
Before calling service personnel, please check the following chart for a possible cause to the  
trouble you are experiencing.  
Symptom  
Solution  
Power is not turned on. Be sure the power cord is plugged in.  
No sound.  
The headphones may be plugged in.  
Poor color/tint.  
The contrast, color and tint may need to be adjusted.  
If you change the direction of the TV while the TV is on, the picture  
may suffer from color shading. If so, turn off the TV and allow about  
30 minutes to cool, then turn on the TV again. The picture may  
be improved.  
Spots appear on  
the screen.  
The broadcast signal may be jammed by other electrical sources  
such as cars, motorcycles, electric trains, high tension lines,  
neon signs, hair dryers.  
Lines appear on  
the screen.  
The broadcast signal may be jammed by other TV receivers, personal  
computers,andTVgames,aswellasinterferencefromradiostations.  
Double or triple  
images.  
Interferencemaybeduetobroadcastwavesreflectedfrommountains  
or buildings.  
Check if the direction of the antenna has changed due to strong wind.  
Snowy picture.  
The antenna lead may be broken or disconnected.  
Check if the direction of the antenna has changed.  
Remote control does  
not work.  
The batteries in the remote control may be exhausted.  
The batteries may be improperly installed.  
Check that there is no obstruction between the remote control and  
the remote (infrared) sensor.  
Check that a strong light is shining on the remote (infrared) sensor.  
Check that the main power is not turned off.  
The following phenomena are not malfunctions  
The cabinet clicks.  
The clicking is a creaking sound produced when the cabinet expands  
or contracts due to changes in the temperature. This will not affect  
the picture or sound.  
Unevenness in color  
sometimes develops  
in part of the screen.  
If the brightness is set too high, such unevenness in color may occur  
depending upon the nature of the picture. The proper color can be  
restored by reducing the contrast.  
19  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
19  
23/9/05, 9:28 AM  
 
SPECIFICATIONS  
MODEL  
29CZ5DE/ 29CZ6DA/29CZ6TES  
Rated voltage  
~ 110 V240 V, 50/60Hz  
Power consumption  
(at ~ 220V, 50Hz)  
123W  
Dimensions  
(Width x Depth x Height)  
782.1(W) X 492.5(D) X 585.1(H) mm  
44 kg  
Mass  
Picture Tube  
Type 29 Flat super crystal picture tube  
(727.4mm) Overall picture tube measured diagonally  
(676mm) Viewable picture tube measured diagonally  
104° deflection  
Television system Channel  
(Antenna input) coverage PAL  
System  
Channel VHF  
B/G CCIR 2 - 12 21 - 69  
UK –– 21 - 69  
D/K CHINA  
UHF  
CATV  
X~Z+2, S1~S41  
––  
Z-1~ Z-38  
X~Z+2, S1~S41  
X1~X19  
PAL  
PAL  
I
1 -12 13 - 57  
2 - 12 21 - 69  
1 -12 21 - 69  
SECAM B/G CCIR  
SECAM D/K OIRT  
NTSC  
NTSC  
M
M
US  
JAPAN  
2 -13 14 - 69 A-6~A-1, A~W, AA~ZZ, AAA, BBB  
1-12 13 - 62 M1~M10, S1~41  
Special RF Color system  
Signal  
NTSC4.43, PAL 60Hz  
Sound system 5.5/6.0/6.5 MHz  
Color system  
Sound output  
Speaker  
PAL50/PAL60/SECAM/NTSC4.43/NTSC3.58  
10 W X 2  
6 x 12cm (2)  
Terminals  
Input [a(1)  
Input [a(2)/DVD]  
: S-Video/Video, Audio L/MONO, Audio R  
B
B
R
R
:
Video/Y, P /C , P /C , Audio L/MONO,  
Audio R  
Input [a(3)]  
: Video, Audio L/MONO, Audio R  
Output [  
Headphone output  
>(MONITOR)] : Video, Audio L/MONO, Audio R  
: Ø 3.5 mm (mini jack stereo type)  
Accessories  
Remote control  
Batteries (R03, AAA)  
This Owners Manual  
(1)  
(2)  
Design and specifications are subject to change without notice.  
Help to recycle, this product indicates material names on main plastic parts.  
EN-01-20[29CZ5DE/29CZ6DA/TES]-1  
20  
23/9/05, 9:28 AM  
 

Technicolor Thomson Home Theater System DPL4911 User Manual
Texas Instruments Computer Hardware MSP FET430 User Manual
Toshiba Flat Panel Television WLT68 User Manual
Toshiba Projection Television 46H84C User Manual
Toyota Automobile Accessories Tacoma 2005 2007 User Manual
Tricity Bendix Oven BS 615 SO User Manual
Vector Power Supply VEC022 User Manual
ViewSonic Computer Monitor PT775 User Manual
Vinotemp Refrigerator VT12TEDS2Z User Manual
VTech Baby Toy 91 002461 270 User Manual