Toyota Automobile Accessories 99 8212 User Manual

INSTA LLATION INSTRUCTIONS FOR PA RT 9 9 -8 2 12  
APPLICATIONS  
2004-2008 Toyota Solara  
9 9 -8 2 12  
KIT FEATURES  
DIN Head Unit Provisions with Pocket  
• ISO DIN Head Unit Provisions with Pocket  
KIT COMPONENTS  
A) Radio Housing w/ Pocket • B) ISO Brackets  
C) Radio Housing Brackets D) (2) PTH-838 Phillips Screws E) (8) PFH-614 Phillips Screws  
F) Trim Plate G) X-9002 Radio Support Bracket  
D
E
C
A
B
F
G
TOOLS REQUIRED:  
Socket Wrench • Small Flat Blade Screwdriver Phillips Screwdriver  
1-800-221-0932  
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION Rev.10-02-07  
 
9 9 -8 2 12  
2 0 0 4 -2 0 0 8 TOYOTA SOLA RA  
A
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
1
2
Remove the cover from the hazard  
switch then unclip and remove the  
switch. (Figure A)  
B
Unclip and remove panel above radio  
including A/C vents and clock.  
3
TIP: Start pulling from the inside of  
the hazard switch cavity. (Figure B)  
Unclip and remove panel surrounding  
shifter. (Figure C)  
4
5
C
Unclip and remove pocket and seat  
heater switch panel. (Figure D)  
Remove (4) 10mm screws to extract  
6
radio from sub dash. (Figure E)  
E
D
1
 
9 9 -8 2 12  
2 0 0 4 -2 0 0 8 TOYOTA SOLA RA  
Attach the corresponding radio  
housing bracket to the radio housing  
using the included (8) PFH-614 Phillips  
screws.  
1
Slide the factory climate control into the  
assembled radio housing brackets/radio  
housing assembly and secure with the  
factory hardware.  
2
Attach the radio support to the back of  
the pocket using the supplied (2) PTF-  
838 Phillips screws.  
3
2
 
9 9 -8 2 12  
DIN HEA D UNIT P ROVISIONS  
A
Slide the DIN cage into the radio  
housing and secure by bending the  
metal locking tabs down. (Figure A)  
1
2
Slide the aftermarket head unit into  
the cage and secure. (Figure B)  
B
3
 
9 9 -8 2 12  
ISO DIN HEA D UNIT P ROVISIONS  
A
Mount the ISO Brackets to the head  
unit with the screws supplied with  
the unit. (Figure A)  
1
Slide the head unit into the radio  
opening until the side clips engage.  
(Figure B)  
2
B
Snap the trim plate into the radio  
3
housing. (Figure B)  
4
 
9 9 -8 2 12  
A
B
A)  
B)  
C)  
D)  
Strip wire ends back 1/2"  
Twist ends together  
Solder  
Tape  
C
D
Locate the factory wiring harness in the  
dash. Metra recommends using the proper  
mating adapter and making the connections  
as shown. (Isolate and individually tape off  
the ends of any unused wires to prevent  
electrical short circuit)  
1
Re-connect the negative battery terminal  
and test the unit for proper operation.  
2
Reassemble radio and dash assemblies in  
reverse order of disassembly.  
3
5
 
INST9 9 -8 2 12  
1-800-221-0932  
Rev. 07-02-07  
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION  
INST99-8212  
 

TDK Network Card HHM Series HHM2245SA1 User Manual
TP Link Modem TD 8817B User Manual
Trane Air Conditioner TRG TRC011 EN User Manual
TRENDnet Network Hardware TE100 P21 User Manual
Tripp Lite TV Cables N818 03M User Manual
V7 TV Mount V7MBK2LPCB User Manual
Vermont Casting Griddle VC0620P VC0680P VC0680N User Manual
ViewSonic Car Video System CDE4600 L User Manual
Vixen Telescope R130S User Manual
Vornado Wheelchair AC300 User Manual