Tripp Lite TV Mount DWT1323S User Manual

Owner’s Manual  
Tilt Flat Screen  
Wall Mount  
MODEL: DWT1323S  
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR  
PROPERTY DAMAGE MAY OCCUR!  
27”  
75x75/100x100  
40kg  
MAX  
(88lbs)  
MAX  
Русскоязычная версия настоящего руководства представлена на веб-сайте компании  
Copyright © 2013 Tripp Lite. All rights reserved.  
 
13-09-229-93-32A5-EN.indd  
1
10/31/2013 9:59:04 AM  
Component Checklist  
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to  
DWT1323S  
Package M  
M4X14 (x4)  
M5X14 (x4)  
D5 washer (x4)  
Package W  
Anchor Bolt (x2)  
Concrete Anchor (x2)  
3
 
13-09-229-93-32A5-EN.indd  
3
10/31/2013 9:59:04 AM  
1.Disassemble VESA Plate  
Use a screwdriver to loosen the  
bottom screws in order to separate  
the VESA plate from the wall mount.  
2a. Mount on Wood Stud Wall  
1
2
Find and mark the  
exact location of  
mounting holes  
Anchor Bolt  
3
5mm-8mm  
Drill pilot holes  
Tighten the screw spacing  
5mm-8mm to wall plate.  
Screw the wall  
mount onto  
the wall  
WARNING  
• Make sure that mounting screws are anchored into the center of the studs.  
Use of a stud finder is highly recommended.  
• Installers are responsible to provide hardware for other types of mounting situations.  
• Installers must verify that the supporting surface will safely support the combined  
load of the equipment and all attached hardware and components.  
4
 
13-09-229-93-32A5-EN.indd  
4
10/31/2013 9:59:04 AM  
2b. Mount on Solid Brick and Concrete Block  
1
Mark the exact  
location of  
mounting holes  
2
Concrete Anchor  
Anchor Bolt  
Drill pilot holes  
5mm-8mm  
Screw the wall  
mount onto  
the wall  
Tighten the screw spacing  
5mm-8mm to wall plate.  
WARNING  
• When installing wall mounts on cinder block, verify the actual concrete thickness  
is at least 1-3/8” (35mm) for using the concrete anchors. Do not drill into mortar  
joints! Be sure to mount in a solid part of the block, generally 1” (25mm) minimum  
from the side of the block. It is suggested an electric drill on a slow setting be used  
to drill the hole instead of a hammer drill to avoid breaking out the back of the hole  
when entering a void or cavity.  
• Installers must verify that the supporting surface will safely support the combined  
load of the equipment and all attached hardware and components.  
5
 
13-09-229-93-32A5-EN.indd  
5
10/31/2013 9:59:06 AM  
3. Install the Wall Plate  
(For clarit, outer cover is not shown.)  
Align top hole of wall plate to screw in  
wall and lower the wall plate until the  
screw is seated in upper area of tear-drop  
mounting hole.  
Anchor Bolt  
Install the other screw and level the wall  
plate, then tighten all screws securely.  
6
 
13-09-229-93-32A5-EN.indd  
6
10/31/2013 9:59:09 AM  
4. Install the VESA Plate  
Top of display  
TV  
TV  
TV  
D5 Washer  
M4X14  
M5X14  
or  
D5 Washer  
M4X14  
M5X14  
Screw VESA plate onto the display.  
Tighten all screws but do not over tighten.  
7
 
13-09-229-93-32A5-EN.indd  
7
10/31/2013 9:59:09 AM  
5. Hang the display onto the Wall Plate  
Wall  
Hook the VESA plate (attached the display) onto the wall  
plate and tighten the screw to secure it.  
6. Adjustment  
Wall  
Wall  
+10°  
-15°  
Push or pull from the top or bottom of display to obtain a desired angle.  
Maintenance  
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).  
13-09-229 93-32A5_RevA  
8
 
13-09-229-93-32A5-EN.indd  
8
10/31/2013 9:59:09 AM  

Taylor Thermometer 9842FDA User Manual
Tiffen Camcorder Accessories FGX10 User Manual
Toshiba CRT Television 42WH18B 50WH18B User Manual
Toshiba Printer B 492L User Manual
Tote Vision Computer Monitor LCD 1048HDM User Manual
Traulsen Refrigerator TR35786 User Manual
Uniden Cordless Telephone XC 320 User Manual
Viking Refrigerator Refrigerator Drawer User Manual
Volvo Automobile VHD User Manual
Weed Eater Lawn Mower 96048000100 User Manual