*
Note : The [AUX] LED light will blink once
F. Programming Channel Control.
*Tip : The component will turn off when the
correct three-digit code number has been
entered. You can verify you have selected the
correct code by pressing the [POWER]
button. The component should turn on or off.
STEP4 Press the same [COMPONENT]
button to store the code. The
component LED light will blink twice
to confirm that the code has been
stored.
Operating Instructions
For The AMINO-4
4-Function Remote Control
Introduction
Button Functions
1
3
for each button pressed. Once you
enter the correct code number, the
component will turn off. If the
component does not turn off, press
the next code numbers listed for your
brand until the component turns off.
By following the steps below, the user can
program the channel controls (Channel Up,
Channel Down and Last) from one
component to operate in another component
mode. The default channel control settings
on the remote control is as follows:
The AMINO-4 remote control is designed to
operate the Amino range of Set-Top Boxes
(STBs) and the majority of TVs, VCRs, DVDs
and AUDIO components on the market
today, as shown below.
: TVs, Plasma TVs and LCD TVs
VCR : VCRs and DVDs
*Note : 2 colons If there is more than one
three-digit number listed for your
brand, try one code number at a time
until your component turns off.
C. To Find the Three-Digit Code Number
That was Stored in the component.
STEP1 Press the [COMPONENT] button
(TV, VCR, DVD or AUX) you wish to
verify and the [OK] button
simultaneously for 3 seconds.
*Tip : If you do not press the [INFO] button
within 20 seconds, the component LED
light will turn off and exit set-up mode
and you will need to start over.
STEP2 Press the [INFO] button. The
component LED light will indicate the
three digits that comprise the code
number by blinking the corresponding
number of times for each digit,
separated by a one second interval,
during which time the component LED
light will turn off.
TV
STEP5 Store the three-digit code number
by pressing the [AUX] button once
again. The component LED light will
blink twice to confirm that the code
has been stored.
STB : STB
TV : STB
VCR : VCR
AUX : AUX
STEP4 Store the three-digit code number
by pressing the same [COMPONENT]
button once again. The component
LED will blink twice to confirm that the
code has been stored.
AUX : Audio Receivers and Amplifiers, etc
If you wish to store the TV channel control
in TV mode, use the following steps.
Replacing Batteries
Before you program or operate the remote
control, you must install two new AAA
alkaline batteries.
STEP1 Remove the battery compartment
cover on the back of your remote
control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
2
STEP1 Press the [TV] button and the [OK]
button simultaneously for
3 seconds until the TV LED light
turns on.
*Note : Now turn on the component and test
the component functions on the
remote control. If any function does
not work properly, repeat from STEP
2 using the next code number listed
for your component brand until you
find a perfect match.
*Note : Try all the functions on the remote
control. If any of the functions do
not work as they should, repeat from
Step 2 using the next three-digit code
number from the same brand list.
*Tip : If you do not press the [VOL-] button
within 20 seconds, the TV LED light
will tiurn off and exit set-up mode
and you will need to start over.
B. Auto Search Method.
If the three-digit code numbers assigned to
your brand do not turn off your component or
the code tables do not list your brand, you
can use the Auto Search Method to find the
correct three-digit code number for your
component by performing the following
steps:
E. Programming Volume Control .
STEP2 Press the [VOL -] button.
By following the steps below, the user can
program the volume controls (Volume Up,
Volume Down and Mute) from one device
to operate in another device mode. The
default volume control settings on the remote
control is as follows :
STEP3 Press the [TV] button.
STEP3 Replace the battery compartment
cover.
The TV LED light will blink twice to confirm
the programming.
Example : One blink, three blinks and eight
blinks, separated by a one second
interval during which time the
component LED light turns off,
indicates a code number of 138.
To return to the original default state:
If you wish to restore the STB channel
control in TV mode, repeat the above steps
by pressing [STB] in STEP3 .
STB : TV
TV : TV
STEP1 Turn on the component you wish to
*Note : Ten blinks is equal to the number 0.
VCR : TV
AUX : AUX
operate.
D. Programming AUX to operate a
fourth component (i.e., a second
TV, VCR, or DVD or AUDIO)
lf you wish to store the STB volume control
in STB mode, use the following steps.
STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed
and the [OK] button simultaneously
for 3 seconds. The component LED
will turn on.
G. Low Battery Warning.
When the battery is low and needs to be
replaced with fresh batteries, the remote
control component LED lights will blink 2
times in sequence whenever a [POWER]
button is pressed to turn on components
STEP1 Press the [STB] button and the
[OK] button simultaneously for 3
seconds until the component LED
light turns on.
Programming the Remote Control
STEP1 Turn on the component you wish to
5
operate.
A. Three-Digit Code Programming Method.
*Tip : If you do not press either the CH+ or
CH- button within 20 seconds, the
component button LED light will turn off
and exit set-up mode and you will need
to start over.
STEP2 Press the [AUX] button and the [OK]
button simultaneously for 3 seconds.
The [AUX] LED light will turn on.
*Tip :If you do not press the desired
component button within 20 seconds,
the [AUX] LED light will turn off and exit
set-up mode and you will need to start
over.
The remote control can be programmed by pressing in a three-digit code number that
corresponds to a particular manufacturer and brand of Audio/Video component.
The three-digit code numbers are listed in the Set-up Code Tables on the backside of this
instruction manual.
*Tip : If you do not press the [VOL+] button
within 20 seconds, the component LED
light will turn off and exit set-up mode
and you will need to start over.
Operations
4
H. Memory Lock System.
Device Default: AMINO Set-Top Box.
Volume Default: TV volume and mute through
the TV , with the option of controlling volume and
mute through the STB or AUDIO component.
Refer to section Efor programming the volume
and mute through your STB or AUDIO
component.
This remote control is designed to retain
programmed memory for 10 years even
after batteries are removed from the
remote control.
STEP3 Press the [CH+] or [CH-] button one
step at a time or keep it pressed. The
remote will emit a series of Power
ON/OFF commands. Release the
[CH+] or [CH-] button as soon as the
component turns off.
STEP1 Turn on the A/V component you wish to program. (TV, VCR, DVD or AUX).
STEP2 Press the [VOL +] button.
STEP3 Press the [STB] button.
STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and
the [OK] button simultaneously for 3 seconds. The selected component LED light
will turn on indicating the component is ready to be programmed.
The STB LED light LED will blink twice to
confirm the programming.
STEP3 Press the [COMPONENT] button you
I. Write your component Set-
up codes.
TV Set-up Code Number :
VCR Set-up Code Number :
AUX Set-up Code Number :
wish to operate.
Channel Default: STB channel and number keys
through the STB, with the option of controlling
channel and number keys through the TV or VCR.
Refer to section Ffor programming the channel
and number keys through your TV or VCR.
*Tip : If you do not begin entering code numbers within 20 seconds, the component LED
STEP4 Point the remote control toward the
component you want to program
and enter the three-digit code
number assigned to your TV brand
from the code tables.
To return to the original default state:
*Tip : You can verify that you selected the
correct code by pressing the [POWER]
button again. The component should
either turn on or off.
light will turn off and exit set-up mode and you will need to start over.
If you wish to restore the TV volume
control in STB mode, repeat the above steps
by pressing [TV] in STEP3 .
Universal Remote Control, Inc.
STEP3 Point the remote control toward the selected component and enter the three-digit
code number assigned to your brand from the code tables.
OCE-0040A Rev01(10/25/05)
|