sm
Innovation Beyond Technology
User’s Manual
Model: IP811
Accessory Handset
FEATURING: • Handset Speakerphone
• Headset Compatible (2.5 mm)
58
.
GHz
Digital Spread
Spectrum
Important Safety Instructions
1-800-267-7377. In the US, call VTech Communications, Inc. at 1-800-595-9511.
BEFORE USING YOUR IP 811, CAREFULLY PEEL OFF THE PROTECTIVE FILM
COVERING THE DISPLAYS.
IMPORTANT:
Your IP 811 is an accessory handset for use with the IP 8100-2/8100-
3 systems. You must have one of these base units in order to use the
accessory handset.This manual is designed to familiarize you with the IP
811 accessory handset setup,registration and basic functions. For detailed
instructions, please refer to the IP 8100-2/8100-3 user’s manual.
2
Parts Check List
1. Handset
4. Belt Clip
2. Handset Charger
3. Charger Wall Mounting Bracket
5. User’s Manual
6. Battery Pack
Topurchasereplacementbatteries, visitusonthewebat shop.vtechcanada.com or callVTech
Telecommunications Canada Ltd. at 1-800-267-7377. In US, call VTech Communications,
Inc. at 1-800-595-9511.
NOTE: Use only VTech batteries (part number 89-1324-00-00).
Charger Wall Mounting
Bracket
Handset Charger
Handset
Belt Clip
Battery Pack
User’s Manual
3
The Handset Layout
12
13
16
9.
Speakerphone
1.
2.
3.
4.
5.
6.
7.
8.
Antenna
Earpiece
Volume Control
CID (Scroll Down)
On (Flash)
Voicemail
Dialing Keys (0-9, *, #)
Redial (Pause)
10. LCD Display
11. Select (Menu)
12. Phonebook (Scroll Up)
13. Headset jack (2.5mm)
14. Off (Clear)
15. Intercom
16. Mute (Delete)
4
Setup
Connecting Power to Handset Charger
Because the IP 811 is an accessory handset to the IP 8100-2/8100-3 all you need to
do is choose the location for your handset charger and plug in the power supply into an
electrical outlet.
CAUTION: Use only the VTech power supply provided with your telephone.
Installation of Battery Pack
1. Remove battery compartment cover by
pressing on the indentation and sliding
downward.
2. Place the new battery pack in the handset
with the positive and negative poles aligned
in the battery compartment.
3. Replace the battery pack cover by sliding
it upwards.
4. If the new battery is not already charged,
place the handset in its charger and allow
it to charge for 10-12 hours.
5. After the initial charge, a maintenance
charge of 10-12 hours should be suffi-
cient. Be sure to place the handset in
its charger when not in use to insure maxi-
mum daily performance.
6. Average talk time on a fully charged
battery is about nine hours, standby time
is approximately four days.
5
Setup
Charging of the Handset Battery
The handset of your cordless telephone is powered by a rechargeable battery. It charges
automatically whenever the handset is in its charger.
You should charge the battery for 10-12 hours when you
first receive your phone. You will know the battery needs
charging when:
•
•
The low battery message is displayed:
The handset seems completely dead, the LCD is com-
pletely clear and does not activate when you press the
keys.
IMPORTANT:
1. Do not dispose of battery pack in a fire, it might explode.
2. Do not open or mutilate the battery pack. Toxic substances may be released, causing
harm to eyes or skin.
3. Exercise care in handling battery pack in order to prevent an accidental short of the
charge contacts, potentially causing the batteries to overheat.
4. Do not dispose of this battery pack into household garbage, it should be properly
recycled.
5. Do not charge the batteries with other electrical devices.
6. If the phone will not be used for a long period of time, remove the battery to prevent
possible leakage.
Checking for Dial Tone
After the handset is registered and the battery is charged, press ON on the handset.
The LCD displays PHONE and shows a call timer, and you will hear a dial tone. If not,
see In Case of Difficulty.
Wall Mounting
The wall mount brackets are designed for use on standard wall mount plates
only. wall mounting is optional. Only the handset chargers (not the main base
unit) can be wall mounted.
1. Plug the power adapters into electrical outlets, and the connector to the bottom
of the handset charger.
2. Line up the tabs on the wall mount brackets with the holes at the back of the
handset charger. Snap the wall mount bracket firmly in place.
3. Mount the handset charger on the wall. Position the handset charger so the
mounting studs will fit into the holes on the wall mount bracket. Slide handset
charger down on the mounting studs until it locks into place.
6
Registration
Your IP 811 is an accessory handsets for use with the IP 8100-2/8100-3 base unit. To
register your IP 811 for the first time:
1. After charging the battery, the screen will display:
ENTER BASE
2. Enter the 15 digit base unit ID code, located on
the underside of your IP 8100-2/8100-3 base.
If you make a mistake, press the DELETE key
to backspace (delete characters), then enter the
correct information.
3. Press SEL to complete the registration process.
SEARCHING...
4. Once a valid base ID code has been entered, the
display will blank for a second or two, and then
show:
5. If the base accepts the new handset, after several
seconds the new handset will show:
HANDSET X
Where X is the new handset number
assigned,sequentially, by the base.
NOTE: If any of the digits are entered incorrectly press the DELETE key
to erase a character(s) and carefully re-enter the correct base ID code. If
you have entered any digits incorrectly you will hear an error tone after the
SEL key is pressed. The 15-digit base ID code may contain numbers and
characters, including 0 through 9 and *. Make sure you enter all 15 digits.
7
Handset Indicators
Handset Icons
Icon
Description
MUTE
• Turns on when the microphone is muted.
• Turns on when there are new call log entries.
• Turns on when the ringer is muted.
NEW
• Low battery indicator and charging indicator.
Handset LEDs
LED
Description
• LED is on when in handsfree mode.
SPEAKER
8
Headset Operation
Headset Operation
Your IP 811 handset is equipped with a 2.5mm headset jack for use with an optional ac-
cessory headset for handsfree conversations. If you choose to use the headset option, you
must obtain an optional accessory headset that is compatible with the IP 811.
To purchase a headset, visit us on the web at shop.vtechcanada.com or call VTech
Customer Service at 1-800-267-7377.
Once you have a compatible 2.5mm headset, locate the headset jack on the IP 811 handset.
Connect the plug on the headset cord to the jack (under a small rubber flap) on the cordless
handset. The plug should fit securely. Do not force the connection.
NOTE:
•
•
Whenever a compatible headset is conn-
ected to the cordless handset, the micro-
phone on the handset will be muted. This
is done to limit the effect of background
noise.
When a compatible headset is connected
to the cordless handset, your speaker-
phone feature will be disabled. To use
your speakerphone feature, simply dis-
connect the headset from the handset.
Belt Clip
The IP 811 is also equipped with a detachable
belt clip.Align the pins on the inside edge of the
clip with the notches on the sides of the handset.
The belt clip should snap securely into place.
Do not force the connection.
9
Maintenance
Taking Care OfYour Telephone
Your cordless telephone contains sophisticated electronic parts, so it must be
treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your
telephone if you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors
in the rain, or handle it with wet hands. Do not install your base unit near a sink,
bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic
equipment. For your own safety, use caution when using electric appliances
during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many
years. Clean it only with a soft cloth slightly dampened with water or a mild soap.
Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you
are wet or standing in water. If your base unit should fall into water, DO NOT
RETRIEVE IT UNTILYOU UNPLUGTHE POWER CORD AND ETHERNET
CABLE FROM THE WALL. Then pull the unit out by the unplugged cords.
10
In Case Of Difficulty
The Phone Doesn’t Work At All
•
•
Make sure the power cord is plugged in.
Make sure the Ethernet cable is plugged firmly into the base unit and the broad-
band connection.
Make sure the batteries are properly charged. If you get a LOW BATTERY mes-
sage or indication, the batteries need charging.
•
No Dial Tone
•
•
First check all the suggestions above.
Please refer to the Troubleshooting section of the Base Unit Features Manual
of IP 8100-2/ 8100-3.
You Get Noise, Static, Or A Weak Signal Even When You’re Near
The Base Unit
•
Household appliances plugged into the same circuit as the base unit can some-
times cause interference. Try to move the appliance or the base unit to another
outlet.
You Get Noise, Static, Or A Weak Signal WhenYou’re Away From
The Base Unit
•
You may be out of range. Either move closer to the base, or relocate the base
unit.
•
The layout of your home may be limiting the range. Try to move the base unit to
another position.
The Handset Does Not Ring WhenYou Receive A Call
•
•
•
Make sure you have the ringers activated. Refer to the section(s) on Ringer
Volume in IP 8100-2/ 8100-3 user's manual.
Make sure the ethernet cable is plugged firmly into the base unit and the broad-
band connection. Make sure the power cord is plugged in.
You may be too far from the base unit.
You Hear Noise In The Handset, And None Of The Keys Or
Buttons Work
•
Make sure the power cord is plugged in.
Common Cure For Electronic Equipment
If the unit does not seem to be responding normally, then try to put the handset
in the charger. If it does not seem to respond, do the following (in the order
listed):
1. Disconnect the power to the base.
2. Disconnect the handset battery pack.
3. Wait a few minutes.
SEARCHING...
4. Connect power to the base.
5. Re-install the battery pack.
6. Watch for handset to display HANDSET X
or your own handset name.
11
Warranty Statement
What does this limited warranty cover?
•
The manufacturer of this VTech product, VTech Communications, warrants to the
holder of a valid proof of purchase (“Consumer” or “you”) that the product and
all accessories provided by VTech in the sales package (“Product”) are free from
material defects in material and workmanship, pursuant to the following terms and
conditions, when installed and used normally and in accordance with operation
instructions, This limited warranty extends only to the Consumer for Products
purchased and used in the United States of America.
What will VTech Communications do if the Product is not free
from material defects in materials and workmanship during the
limited warranty period (“Materially Defective Product”)?
•
During the limited warranty period, VTech’s authorized service representative will
repair or replace at VTech’s option, without charge, a Materially Defective Product.
If we repair this product, we may use new or refurbished replacement parts. If
we choose to replace this product, we may replace it with a new or refurbished
product of the same or similar design. VTech will return repaired or replace ment
products to you in working condition. VTech will retain defective parts, modules, or
equipment. Repair or replacement of Product, at VTech’s option, is your exclusive
remedy.You should expect the repair or replacement to take approximately 30
days.
How long is the limited warranty period?
•
The limited warranty period for the product extends for ONE(1) YEAR from the
date of purchase if we repair or replace a Materially Defective Product under the
terms of this limited warranty. This limited warranty also applies to repaired or
replacement Products for a period of either (a) 90 days from the date the repaired
or replacement Product is shipped to you or (b) the time remaining on the original
one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover
1. Product that has been subjected to misuse, accident, shipping or other physical
damage, improper installation, abnormal operation or handling, negligent, inun-
dation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone
other than an authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions,
network reliability or cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech electrical
accessories; or
5. Product whose warranty/quality stickers, Product serial numbers plates or elec
tronic serial numbers have been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the
United States, or used for commercial or institutional purposes (including but
not limited to Products used for rental purposes); or
7. Product returned without valid proof of purchase (see 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation
or repair of systems outside the unit.
12
Warranty Statement
How do you get warranty service?
•
To obtain warranty service in the United States of America, call 1- 800-595- 9511
for instructions regarding where to return the Product. Before calling for service,
please check the user’s manual. A check of the Product controls and features may
save you a service call.
•
Except as provided by applicable law, you assume the risk of loss or damage dur-
ing transit and transportation and are responsible for delivery or handling charges
incurred in the transport of Product(s) to the service location. VTech will return
repaired or replaced product under this limited warranty to you, transportation,
delivery or handling charges prepaid. VTech assumes no risk for damage or loss
of the Product in transit.
•
If the Product failure is not covered by this limited warranty, or proof of purchase
does not meet the terms of this limited warranty, VTech will notify you and will re-
quest that you authorize the cost of repair and return shipping costs for the repair
of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the
VTech service location along with a description of the malfunction or difficulty;
2. Include “valid proof of purchase” (sales receipt) identifying the Product
purchased (Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone
number.
Other Limitations
•
This warranty is the complete and exclusive agreement between you and VTech. It
supersedes all other written or oral communications related to this Product.VTech
provides no other warranties for this product. The warranty exclusively describes
all of VTech’s responsibilities regarding the product.
There are no other express warranties. No one is authorized to make modifications to
this limited warranty and you should not rely on any such modification.
State Law Rights:This warranty gives you specific legal rights, and you may also have
other rights, which vary from state to state.
Limitations: Implied warranties, including those of fitness for a particular purpose and
merchantability (an unwritten warranty that the product is fit for ordinary use) are limited
to one year from date of purchase. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitation may not apply to you.
•
In no event shallVTech be liable for any indirect, special, incidental, consequential,
or similar damages (including, but not limited to lost profits or revenue, inability to
use the product, or other associated equipment, the cost of substitute equipment,
and claims by third parties) resulting from the use of this product, some states do
not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
13
FCC, ACTA, and IC Regulations
This equipment complies with Parts 15 of the Federal Communications Commission
(FCC) rules for the United States.It also complies with regulations RSS210 and CS-03
of Industry and Science Canada. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any inter-
ference, including interference that may cause undesired operation of the device.
A label is located on the underside of the base unit containing either the FCC regis-
tration number and Ringer Equivalence Number (REN) or the IC registration number
and Load Number. You must, upon request, provide this information to your local
telephone company.
This equipment is compatible with inductively coupled hearing aids.
Should you experience trouble with this telephone equipment, please contact:
FCC Part 15
Warning:Changes or modifications to this unit not expressly approved by the party re-
sponsible for compliance could void the user’s authority to operate the equipment.
The equipment has been tested and found to comply with part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try and correct the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet or on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
To ensure safety of users, the FCC has established criteria for the amount of radio
frequency energy that can be safely absorbed by a user or bystander according to the
intended usage of the product.This product has been tested and found to comply with
the FCC criteria. The handset has such a low power that it does not require testing.
It may be safely held against the ear of the user. The base unit shall be installed &
used such that parts of the user’s body other than the hands should be maintained at
a comfortable distance of approximately 20 cm or more.
IC (Industry Canada)
This telephone is registered for use in Canada.
The term “IC:”before the radio certification number only signifies that Industry Canada
technical specifications were met.
14
FCC, ACTA, and IC Regulations
Notice:
This equipment meets the applicable Industry Canada Terminal Equipment Technical
Specifications.This is confirmed by the registration number.The abbreviation,IC,before
the registration number signifies that registration was performed based on a Declaration of
Conformity indicating that Industry Canada technical specifications were met. It does not
imply that Industry Canada approved the equipment.
Notice:
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN
assigned to each terminal equipment provides an indication of the maximum number
of terminals allowed to be connected to a telephone interface.The termination on an
interface may consist of any combination of devices subject only to the require-
ment that the sum of the Ringer Equivalence Numbers of all the devices does not
exceed five.
Before installing this equipment, users should ensure that it is permissible to be con-
nected to the facilities of the local telecommunications company.The equipment must
also be installed using an acceptable method of connection. The customer should
be aware that compliance with the above conditions may not prevent degradation of
services in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.
Caution:
Users should not attempt to make such connections themselves, but should contact the
appropriate electrical inspection authority, or electrician, as appropriate.
Your cordless phone is designed to operate at the maximum power allowed by the
FCC and IC. This means your handset and base unit can communicate only over a
certain distance - which will depend on the location of the handset and base unit,
weather, and the construction and layout of your home or office.
15
Technical Specifications
FREQUENCY CONTROL
SIZE
Crystal controlled
PLL synthesizer
Handset: 182mm x 55.3mm x 40mm
(including antenna)
Charger: 76.5mm x 79.4mm x 45.2mm
TRANSMIT FREQUENCY
Base: 5725 - 5850 MHz
WEIGHT
Handset: 2400 - 2483.5 MHz
Handset: 146 grams
(excluding Battery)
Charger: 225 grams
RECEIVE FREQUENCY
Base: 2400 - 2483.5 MHz
Handset: 5725 - 5850 MHz
POWER REQUIREMENTS
CHANNELS
Handset: 3.6V @ 600mAh NiMH
Charger: 9 V DC @ 150mA
95 Channels
MEMORY
NOMINAL EFFECTIVE RANGE
Phonebook: 50 Memory locations; up to
32 digits for number, 16 characters for
name, per location.
Maximum power allowed by FCC and
IC. Actual operating range may vary
according to environmental conditions at
the time of use.
CID: 50 memory locations
SPECIFICATIONS ARE TYPICAL
AND MAY CHANGE WITHOUT
NOTICE.
16
Table Of Contents
IMPORTANT SAFETY INSTRUCTIONS .......................................................... 1
Parts Check List........................................................................................... 3
The Handset Layout..................................................................................... 4
GETTING STARTED......................................................................................... 5
Set Up.......................................................................................................... 5
Connecting Power to Handset Charger .............................................................. 5
Installation of Battery....................................................................................... 5
Charging of the Handset Battery ....................................................................... 6
IMPORTANT .................................................................................................. 6
Checking for Dial Tone..................................................................................... 6
Registration.................................................................................................. 7
BASIC OPERATION. ........................................................................................ 8
Handset Indicators...................................................................................... 8
Handset Icons ................................................................................................ 8
Handset LED.................................................................................................. 8
ADVANCED OPERATION................................................................................ 9
Headset Operation....................................................................................... 9
Belt Clip ....................................................................................................... 9
ADDITIONAL INFORMATION ........................................................................ 10
Maintenance .............................................................................................. 10
In Case Of Difficulty................................................................................... 11
Warranty Statement................................................................................... 12
FCC, ACTA, and IC Regulations.............................................................. 14
Technical Specifications ............................................................................ 16
Congratulations on your purchase
of this VTech product
NEED HELP?
Our representatives are here
to help you with any questions
concerning the operation of this
product, available accessories,
or any other related issues.
Call Toll Free:
1-800-595-9511
In Canada, Call:
1-800-267-7377
or visit our website at
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc. Beaverton, Oregon, 97008
Distributed in Canada by VTech Telecommunications Canada Ltd., Richmond, B.C.
V6X 1Z9.
Copyright © 2005 for VTECH TELECOMMUNICATIONS LTD.
Printed in China
91-000296-010-000
ISSUE 0
|