VTech Telephone 5878 User Manual

STEP 4 Set the answering system clock  
• Press CLOCK to hear the current clock setting.  
• Press CLOCK again to change the settings.  
• Press /SKIP or /REPEAT to change the year,  
hour, minute or date.  
Quick start guide  
for models ia5870/5878/5882  
When the correct setting is announced, press CLOCK  
to advance to the next setting.  
STEP 1 Connect power to telephone base  
and chargers then connect telephone line to  
telephone base  
NOTE:  
For complete feature instructions, please refer to your  
user’s manual.  
• Plug the connector into the power jack at the bottom  
of the telephone base and chargers then plug the  
power adapter into an electrical outlet not controlled  
by a wall switch.  
• Plug one end of the telephone line cord into the  
telephone line jack at the bottom of the telephone  
base. Then plug the other end of the cord into the  
modular wall telephone outlet.  
STEP 3 Make, receive, and end calls  
Make a call  
STEP 7 Charge the battery  
Press TALK/FLASH to ensure there is a dial tone,  
• The battery may have enough charge for a short  
call. For best performance, charge the battery for at  
least 16 hours.  
then dial the telephone number.  
• To charge the handset, place it in the telephone  
base or charger.  
STEP 5 Turn the answering system on and off  
SELECT  
• The CHARGE light on the telephone base or  
charger will be on when the handset is properly  
positioned. See Troubleshooting in the user’s  
manual if the CHARGE light is not on.  
The answering system must be turned on to function.  
If the answering system is turned off, the telephone  
base light will be off.  
To turn the answering system on/off:  
For installation and use of the belt clip and the wall  
mount bracket, please consult the user’s manual.  
-OR-  
• Press ANS ON/OFF to select on or off.  
For predialing:  
• Dial the number (press  
to backspace, or press  
IMPORTANT!  
and hold REDIAL/PAUSE to insert a pause).  
If your product is not working properly:  
• Refer to the Troubleshooting section of your  
user’s manual.  
Receive a call  
• Press TALK/FLASH or any dialing keys (0-9, #, *)  
NOTE: Use only the power adapter supplied with  
your VTech telephone or equivalent.  
STEP 6 Record outgoing announcement  
(optional)  
The telephone is pre-set with the announcement  
Hello, please leave a message after the tone.” To  
replace the announcement with your own:  
• Press ANNC and the system announces  
“Announcement, press PLAY or press RECORD.”  
• Press RECORD to record, and the system  
announces “Record after the tone. Press STOP  
when you are done.”  
• After the tone, speak towards the microphone at the  
front right of the telephone base from about nine  
inches away.  
SELECT  
STEP 2 Install the battery  
• Align the two holes in the plug with the socket  
pins matching the color-coded label in the battery  
compartment of the handset, then snap the plug  
securely into place.  
• Place the battery in the compartment with the wires  
in the upper right corner.  
• Position the battery compartment cover and slide it  
towards the unit until it clicks into place.  
• For optimal performance, we recommend that you  
charge the handset for 16 hours. Note that the new  
battery may have enough charge for some calls.  
End a call  
• Press OFF, or put the handset in the telephone base  
or charger.  
SELECT  
• Press  
/PLAY/STOP when finished and the  
answering system will automatically playback the  
newly recorded announcement.  
96-006322-010-100  
issue 0  
 

Technicolor Thomson Network Router 610 User Manual
Technika CRT Television 19 811 User Manual
Thermador Dishwasher DWHD94EP DWHD94BS DWHD94BP User Manual
Timex Clock Radio T237 User Manual
Toshiba Personal Lift GRT100 User Manual
Toshiba Projector TLP XE30 User Manual
Uniflame Outdoor Fireplace WAD997SP User Manual
Univex All in One Printer X7675 User Manual
Vermont Casting Indoor Fireplace TBREF36 User Manual
Victor Corp Flat Panel Television LT 26S60BU User Manual