Vector Camping Equipment VEC128BW User Manual

WARRAN TIES  
1 2 0 DAY LIMITED WARRAN TY REGISTRATIO N FO RM  
VEC1 2 8 BW  
VEC1 2 8 R  
VEC1 2 8 Y  
All Vector Manufacturing, Ltd. products are warranted to the original purchaser only for 120 days from the date  
of purchase, to be free of defects in materials and workmanship. Vector Manufacturing, Ltd. disclaims any liability  
for consequential damages. In no event will Vector Manufacturing, Ltd. be responsible for any amount of damages  
beyond the amount paid for the product at retail. In the event of a defective item, please ship the item prepaid,  
with a complete explanation of the problem, your name, address and daytime telephone number. Vector  
Manufacturing, Ltd. will, at its option, replace the defective part.  
THE FO LLO W IN G SITUATIO N S ARE N O T CO VERED UN DER THIS WARRAN TY:  
Cost of shipment to Vector Manufacturing, Ltd.  
Normal wear and tear, including chips, scratches, abrasions, repairs by unauthorized persons or failure to follow  
recommended care and use instructions. Damage caused by misuse, abuse, neglect, alterations, repairs by  
unauthorized persons, or failure to follow recommended care and use instructions.  
Bulbs and batteries.  
PLEASE ACTIVATE MY LIMITED WARRAN TY FO R MO DEL #  
.
————  
Enclose copy of original sales receipt.  
SPO RTSPO T®  
Name _________________________________________________________________________________________  
Street Address __________________________________________________________________________________  
City __________________State ____Zip Code ____________ Phone _______________Fax _________________  
E-mail_____________________ Store where purchased ________________________________________________  
UPC Number from package (12 digits) _____________________________________________________________  
LAN TERN CO MBO  
All Vector Manufacturing, Ltd. products must be registered within (10) days of purchase to activate this warranty.  
Mail the completed registration form, along with a copy of the original sales receipt to:  
CO RDED  
AT TN.: CUSTOMER SERVICE • VECTOR MANUFACTURING, Ltd. • 4140 SW 28th Way, Ft. Lauderdale, FL 33312  
CO RDLESS  
RECHARGEABLE  
9 0 °  
3 YEAR EXTEN DED WARRAN TY REGISTRATIO N FO RM  
Certain Vector Manufacturing, Ltd. products are eligible to be covered to the original purchaser only, for three  
(3) years from the date of purchase, to be free of defects in materials or workmanship. Vector Manufacturing,  
Ltd. disclaims any liability for consequential damages. In no event will Vector Manufacturing, Ltd. be responsible for  
any amount of damages beyond the amount paid for the product at retail. In the event of a defective item, please  
ship the item to us, prepaid, with an explanation of the problem, your name, address and daytime telephone  
number. Vector Manufacturing, Ltd. will, at its option, replace or repair the defective part.  
THE FO LLO W IN G SITUATIO N S ARE N O T CO VERED UN DER THIS WARRAN TY:  
Cost of shipment to Vector Manufacturing, Ltd.  
Normal wear and tear, including chips, scratches, abrasions, discoloration or fading due to usage or  
exposure to sunlight.  
Damage caused by misuse, abuse, neglect, alterations, repairs by unauthorized persons, or failure to follow  
recommended care and use instructions.  
Bulbs, fuses and batteries.  
PLEASE ACTIVATE MY EXTEN DED WARRAN TY FO R MO DEL #  
.
————  
Enclose copy of original sales receipt.  
Name _________________________________________________________________________________________  
Street Address __________________________________________________________________________________  
City __________________State ____Zip Code ____________ Phone _______________Fax _________________  
E-mail_____________________ Store where purchased ________________________________________________  
Date Item Purchased ________ Item Purchased _______________________________________________________  
UPC Number from package (12 digits) _____________________________________________________________  
PATENT PENDING  
O W N ER'S MAN UAL &  
FORM OF PAYMENT (US$15.00)  
[
] Check  
[
] Money Order  
WARRAN TY IN FO RMATIO N  
All Vector Manufacturing, Ltd. products must be registered within (10) days of purchase to activate this  
warranty. Mail the completed registration form, along with a copy of the original sales receipt, and a check or  
money order for US$15.00 made payable to Vector Manufacturing, Ltd., to:  
4 1 4 0 S.W. 2 8 TH WAY  
FT. LAUDERDALE, FL 3 3 3 1 2  
AT TN.: CUSTOMER SERVICE • VECTOR MANUFACTURING, Ltd. • 4140 SW 28th Way, Ft. Lauderdale, FL 33312  
TEL 9 5 4 .5 8 4 .4 4 4 6 FAX 9 5 4 .5 8 4 .5 5 5 6  
WARRANTY MUST BE PURCHASED WITHIN 90 DAYS OF PRODUCT PURCHASE DATE.  
WARRANTY IS NON-TRANSFERABLE AND NON-REFUNDABLE.  
 
8. Grasp the Tube Socket and push on the fluorescent tube base to disconnect  
the tube from the socket.  
9. Do not allow the tube to drop.  
1 . IN TRO DUCTIO N  
Congratulations on purchasing the Vector SportSpot Lantern, an advanced  
design combination spotlight and lantern. It instantly converts use from a  
powerful spotlight to a soft, long-lasting area light. See Figure 1A and 1B. It  
uses a powerful proven-technology, rechargeable, sealed lead acid battery that  
allows for years of dependable use, recharge after recharge. It was designed  
from the ground up to be the most versatile and practical light for travel,  
camping, picnicking, tailgate parties and boating. The SportSpot Lantern gives  
you the kind of light you need, when and where you need it.  
10. Follow local procedures for safe fluorescent tube disposal.  
7.2. FLUORESCENT TUBE INSTALLATION  
1. Make sure that the Lantern Switch is Off.  
2. Press the new fluorescent tubes base into the Tube Socket Assembly.  
3. Replace the Tube Socket Assembly so that the two Support Rods pass  
through the assembly and it is fully seated against the clear plastic dome.  
4. Replace the two nuts and tighten (clockwise) so that the tube assembly is snug.  
5. Screw on (clockwise) the End Cap until it is snug.  
FIGURE 1 A  
FIGURE 1 B  
6. Test the fluorescent tube for proper operation by reconnecting the battery  
and turning On the Lantern switch.  
8 . FUSE REPLACEMEN T  
9 0 °  
The fuse is located inside the DC plug. See Figure 5 for fuse replacement.  
Make sure the DC Recharger connector is disconnected from the SportSpot Lantern.  
SPOTLIGHT ON/ OFF  
LANTERN SWITCH  
FLANGE  
CONTACT  
SPRING  
PLUG  
RECHARGE LEDS  
FUSE  
FUSE REPLACEMENT PROCEDURE  
1. Unscrew (counterclockwise) the flange from the DC plug  
2. Remove the flange, contact and fuse from the plug assembly.  
3. Replace fuse with a 10 -ampere fuse of same type and size.  
4. Place the center contact in the flange.  
5. Replace the center contact and flange on the DC plug.  
6. Tighten (clockwise) until the flange is fully seated.  
DO NOT OVERTIGHTEN FLANGE  
Two recharge adapters are supplied with the SportSpot Lantern. It is recharge-  
able from either a DC cigarette lighter type 12-volt DC socket (accessory  
socket) or from any 110/ 120 volt 60 Hz AC receptacle. This permits recharge  
flexibility for use around home, business or in the field. The unit may be oper-  
ated during DC recharge from any 12 volt accessory socket able to supply at  
least 5 Amperes. This feature allows for uninterrupted use when the units  
internal battery becomes discharged and requires recharging. 12 volt DC  
power is available from most vehicles, boats, jump starters and portable  
battery packs. Vector has a variety of portable power products that may be  
considered as companions to your SportSpot Lantern. Contact Vector for addi-  
tional information.  
9 . BATTERY REPLACEMEN T  
The battery is contained in a compartment in the base of the unit. A plate must  
be removed to gain access to the battery. Figures 5A and 5B show access to  
the battery compartment.  
FIGURE 5 A  
FIGURE 5 B  
BATTERY  
COMPARTMENT  
COVER  
TAB  
SWITCH  
SPADE  
CONNECTOR  
AC/ DC  
RECHARGE  
BARREL  
SPADE  
LUG  
RECEPTACLE  
SPADE CONNECTOR  
TERMINALS  
BATTERY  
6
1
 
10. Check the spotlight operation by reconnecting the battery and turning On the  
switch.  
2 . FEATURES  
1,000,000 Candle Power spot light.  
• Powerful replaceable H-3 Series 12 volt quartz halogen bulb in spotlight.  
• Powerful replaceable 9-watt fluorescent U-shaped tube in lantern.  
• Head swivels 90 degrees for soft, 360 degree area lighting.  
Rubber safety guard protects spotlight.  
Recharging LED and battery FULL LED.  
Recharges from standard North American Standard 110 VAC,  
60 Hz, receptacle.  
Operates and simultaneously recharges from 12 volt DC accessory socket.  
Three way switch - Spotlight, Off and Lantern.  
• Comfortable handgrip.  
7 . LAN TERN TUBE REPLACEMEN T  
The Lantern fluorescent tube is mounted on a socket assembly. Power is sent to  
the tube socket through the two support rods. It is very important to make sure  
the Lantern switch is turned off before removing the end cap. If there are any  
doubts about the On/ Off switch being Off, then skip to the Battery Removal  
section and disconnect the battery before removing the end cap.  
WARN IN G:  
FLUORESCENT TUBES OPERATE WITH HIGH VOLTAGE.  
DO NOT REMOVE END CAP UNLESS POWER IS OFF  
AND THE BATTERY IS DISCONNECTED. SEE SECTION 9  
• Stable base prevents tip over in any head position  
NOTE:  
See Figure 4 for Fluorescent (6) Tube Replacement  
This unit is shipped in a partially charged state. Charge unit using either  
AC or DC method until the green LED lights. Charge after each use. Initial  
charge should be for 12 hours.  
FIGURE 4  
4
3
5
1
3 . O PERATIO N  
2
The swivel action of the unit keeps the lamp head securely in position for use  
while carrying, or while on tabletop. The range of swivel motion is greater than  
90 degrees with five locking positions. The spotlight position (upright) focuses  
light straight ahead. The lantern position (spotlight tilted forward 90 degrees)  
floods light in a 360-degree pattern for reading, cooking, and tailgating, etc.  
A three-position switch (Spotlight, Off, Lantern) controls on/ off operation of  
both lights. The switch is protected by a flexible covering that protects it from  
dust, dirt and moisture. This ensures reliability and extends the life of the switch.  
The Spot Light can be continuously lit for up to 20 minutes on a full battery  
charge; the lantern can be lit for up to five (5) hours on a full battery charge.  
Either light can be operated during DC recharge.  
6
1. DOME  
2. FLUORESCENT TUBE  
3. TUBE SOCKET ASSEMBLY  
4. NUTS  
5
END CAP  
6. SUPPORT RODS  
4 . RECHARGE  
All batteries lose charge over time, especially when they are warm. Frequent  
battery recharges will extend battery life. AC recharge is recommended every  
two months, when not in frequent use. Use the AC recharge adapter and  
charge until battery is full. AC and DC recharge connections are through a  
heavy-duty barrel receptacle at the lower rear of the unit. See figure 5A. Two  
LED indicators display the status of recharge. Continue recharge operation until  
the two LEDS are equally bright. See figure 1A.  
7.1 FLUORESCENT TUBE REMOVAL  
1. Make sure that the Lantern Switch is Off.  
2. Rest the unit on a secure tabletop.  
3. Position the head to be in the Spotlight position.  
4. Unscrew (counter clockwise) the End Cap and set aside.  
5. Unscrew (counter clockwise) the two nuts from the two support rods and set  
them aside.  
6. Slide the Tube Socket assembly away from the head and remove it from  
the two support rods.  
7. Set it on a stable work surface like a table, bench,etc.  
2
5
 
SPOTLIGHT BULB REMOVAL / INSTALLATION  
AC AND DC RECHARGE ADAPTERS  
4
5
6
3
FIGURE 3  
FIGURE 2 A  
FIGURE 2 B  
2
DC RECHARGEABLE  
ADAPTER  
AC RECHARGEABLE  
ADAPTER  
7
FUSED DC PLUG  
1
8
1. SAFETY RING  
2. RETAINING RING TAB  
Open  
BARREL CONNECTOR  
9
3. RETAINING RING LENS  
4. LENS  
10  
4.1 AC RECHARGE  
5. O-RING  
6. REFLECTOR/ LAMP ASSEMBLY  
7. NOTCH  
8. RETAINING WIRES  
9. WHITE WIRE  
10. GREEN OR BLACK WIRE  
11. SCREW  
11  
Closed  
The AC Recharge adapter provides 300 mA at 12 Volts DC for recharging the  
batteries. Power the AC Recharger from a standard, 110 volt, 60 Hz AC North  
American receptacle. The AC recharger will not support lamp operation. Do  
not operate the lamps while the AC Recharger is connected to the Recharge  
Port. Charge with lamps Off until LEDs are equally bright. This steady recharge  
will prolong battery life. Only use the supplied AC Recharger—DO NOT  
SUBSTITUTE WITH ANOTHER. SEE FIGURE 2A  
9
10  
11  
6.1 SPOTLIGHT BULB REMOVAL PROCEDURE  
1. Rest the unit on a secure tabletop.  
2. Position the head to be in the Spotlight position.  
3. Lift off the rubber Safety Ring and set it aside.  
4.2 DC RECHARGE/ OPERATION  
4. Grasp the Retaining Ring and rotate it slightly clockwise until the  
rings tab lines up with the notch in the head.  
5. Lift off the retaining ring.  
6. Pull the lens, “Oring and reflector assembly from the head.  
7. Set the lens and “Oring aside.  
8. The Reflector/ Lamp Assembly should be hanging from the two wires.  
9. On the Reflector Assembly, carefully squeeze the two retaining wires  
together and lift them to release them from the “Tslot.  
10. Loosen the screw—item #11.  
11. Rotate the two retaining wires upward as shown, to allow the bulb to lift out.  
12. Disconnect the white wire by pulling apart the two connectors on the wire.  
13. Follow local procedures for bulb disposal.  
The DC Recharge adapter provides 12 Volts DC for simultaneously recharging  
the batteries and operating either light. Power the DC Recharger from a stan-  
dard, 12-volt DC cigarette lighter type accessory socket. Charge until LEDs are  
equally bright. After recharge, either disconnect the DC recharger or leave  
connected and continue to operate either light. Only use the supplied DC  
Recharger - do not substitute with another. The DC Recharge Adapters DC Plug  
is equipped with a user-replaceable 10-ampere fuse. SEE FIGURE 2B  
5 . MAIN TEN AN CE/ PARTS REPLACEMEN T  
If the unit has dirt on it, gently clean the outer surfaces of the SportSpot Lantern  
with a soft cloth moistened with a mild solution of water and detergent.  
Periodically inspect the condition of recharge adapters, connectors, and wires.  
Replace any components that may have become worn or broken.  
6.2 SPOTLIGHT BULB INSTALLATION PROCEDURE  
1. Insert the new bulb in the Reflector/ Lamp Assembly.  
2. Rotate the two retaining wires downward as shown, to hold the bulb in place.  
3. Tighten the screw— item #11.  
4. Connect the white wire by pushing together the two connectors.  
5. On the reflector Assembly, carefully squeeze the two retaining wires together  
and place them in the “Tslot.  
6. Replace the Reflector/ Lamp Assembly, “ORing and Lens.  
7. Place the Retaining Ring so that it’s tabs are aligned with the notches in the head.  
8. Press the Retaining Ring until it is fully seated and rotate it slightly counter clock–  
wise to secure it against the head.  
Four parts are replaceable by users. The quartz halogen bulb and the fluorescent  
tube are proprietary and are only available through Vector Manufacturing. The  
sealed lead acid battery and fuse are available from Vector as well as from popular  
automotive parts suppliers nationwide. Contact Vector Manufacturings Technical  
Support Department for replacement parts and any additional information that you  
may need. They may be reached at (954) 584-4446.  
6 . SPO TLIGHT BULB REPLACEMEN T  
9. Replace the rubber Safety Ring by pushing it onto the Retaining Ring. Make  
sure the Safety Ring is fully seated.  
See Figure 3 for bulb removal and replacement. Make sure that the On/ Off  
Switch is Off and disconnect the battery. SEE SECTION 9.  
4
3
 

Teac MP3 Player SR L70i User Manual
Technicolor Thomson Stereo System CS104 User Manual
Toastmaster Toaster T2020B User Manual
Toshiba Computer Drive SD M1802 User Manual
TRENDnet Network Hardware TEW455APBO User Manual
Tricity Bendix Oven SURREY User Manual
Tripp Lite TV Cables S457 010 User Manual
Tunturi Treadmill J661F User Manual
Uniden Telephone MC 722 User Manual
Verizon Telephone NSQ412 User Manual