Vector Work Light 90519434 User Manual

SLH100V  
Hig h In te n sity Disch a rg e Sp o tlig h t  
Co rd le ss Re ch a rg e a b le  
IN STRUCTIO N MAN UAL  
& WARRAN TY IN FO RMATIO N  
IMPO RTAN T SAFETY IN FO RMATIO N , SAVE THESE IN STRUCTIO N S  
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND  
THIS INSTRUCTION MANUAL. THIS MANUAL CONTAINS IMPORTANT  
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS PRODUCT.  
4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312  
Toll Free: (800) 544-6986  
Cat. # SLH100V  
MARCH 07  
Form # 90519434  
Printed in China  
 
O UTDO O R USE EXTEN SIO N CO RDS. When tool is used outdoors, use only extension cords  
intended for use outdoors and so marked.Safety guidelines / definitions  
Minimum Gage for Cord Sets  
Volts  
Total Length of Cord in Feet  
120V  
0-25  
(0-7,6m) (7,6-15,2m)  
0-50 51-100  
26-50  
51-100  
101-150  
(15,2-30,4m)  
101-200  
(30,4-45,7m)  
240V  
201-300  
(0-15,2m) (15,2-30,4m) (30,4-60,9m)  
(60,9-91,4m)  
Ampere Rating  
More  
Than  
Not more  
Than  
6
10  
12  
American Wire Gage  
0
6
-
-
18  
18  
16  
14  
16  
16  
16  
12  
16  
14  
14  
14  
12  
12  
10 -  
12 -  
16  
Not Recommended  
SAFETY GUIDELINES/DEFINITIONS  
DAN GER: Indicates an imminently hazardous situation which, if not avoided, will result in death or  
serious injury.  
WARN IN G: Indicates a potentially hazardous situation which, if not avoided, could result in death  
or serious injury.  
CAUTIO N : Indicates a potentially hazardous situation which, if not avoided, may result in minor or  
moderate injury.  
CAUTIO N : Used without the safety alert symbol indicates potentially hazardous situation which, if not  
avoided, may result in property damage.  
WARNING: RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety  
precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance  
or modification of tools or equipment could result in serious injury and property damage. There are certain  
applications for which tools and equipment are designed. Vector Products, Inc. strongly recommends that this  
product NOT be modified and/ or used for any application other than for which it was designed. Read and  
understand all warnings and operating instructions before using any tool or equipment.  
SAVE THESE INSTRUCTIO NS  
THIS MAN UAL CO N TAIN S IMPO RTAN T SAFETY AN D O PERATIN G IN STRUCTIO N S FO R  
THE HID SPO TLIGHT SLH1 0 0 V.  
WARN IN G: TO REDUCE THE RISK O F IN JURY:  
• Follow these instructions and those published by the manufacturer of any equipment you intend to use  
with this unit. Review cautionary markings on these products.  
IMPORTANT SAFETY INSTRUCTIONS  
WARN IN G: This product or its power cord contains lead, a chemical known to the State of  
California to cause cancer and birth defect or other reproductive harm. Wash hands after handling.  
WARN IN G: RISK O F ELECTRIC SHO CK: This light contains high voltage components. Do not  
disassemble this light other than to replace or recycle the battery. Should this light become damaged,  
immediately discontinue use and return it to an authorized service center for repair.  
This light is for dry location use only. Never expose this light to rain.  
Do not operate light with damaged cord or plug; or if the unit has received a sharp blow, been  
dropped, or otherwise damaged in any way. Evidence of tampering with the light will void the warranty.  
• Do not operate this unit with a missing or damaged guard or glass lamp containment barrier.  
• Do not immerse this spotlight in water. This unit is not waterproof.  
WARN IN G: RISK O F IN JURY TO EYES AN D SKIN FRO M UV EXPO SURE: The glass of the  
bulb reduces the amount of UV radiation emitted by the bulb. Never operate the light if you suspect the  
bulb is cracked or see that it is broken. Prior to each use look for evidence of bulb damage and if  
suspected or observed do not use the light. Return the light to an authorized service center for repair.  
2
 
Risk of injury to the eye. Never stare directly into the lit spotlight and never shine the spotlight  
into another persons eyes.  
Keep sharp objects away from lens – it is glass and can break.  
WARN IN G: HO T LEN S: Never block the lens of this light. If the light is operated with the lens  
blocked, the lens will get hot and damage materials it contacts and it can burn the skin.  
Never place the light with the lens face-down on any surface when lit.  
Keep lamp away from materials that may burn.  
• Do not touch hot lens, guard, or enclosure.  
Lens can get hot – do not touch lens while spotlight is operating.  
WARN IN G: TO REDUCE THE RISK O F IN JURY: This unit should only be operated by adults; it  
is not for use by children.  
CAUTIO N : TO REDUCE THE RISK O F IN JURY O R PRO PERTY DAMAGE:  
• Charge only with originally supplied 120 volt AC or 12 volt DC charging adapters. Consult your  
authorized service center for replacement.  
Replace batteries with the same size and type indicated in the Specifications in the back of this  
instruction manual.  
• Do not drop or throw spotlight.  
• Do not crush, cut, pull or expose charging adapter cords to extreme heat or sharp edges.  
• Position charging adapter cords so that they do not become entangled and away from lens so that  
they do not become a safety hazard.  
• Always charge in a dry location.  
• Plug in the charging adapter at the spotlight first, then plug into the charging source.  
• After recharge, disconnect charging adapter and wait 5 minutes before use.  
SAVE THESE INSTRUCTIONS  
3
 
TABLE O F CO N TEN TS  
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Unpacking your SLH100V HID Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Controls and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
120 Volt AC Charging/ Recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
12 Volt DC Charging/ Recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Using the Spotlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Using the Adjustable Work Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Safe Battery Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
8
IN TRO DUCTIO N  
Congratulations on purchasing the Vector® HID Sp otlig ht, an advanced design that  
uses powerful, proven-technology, rechargeable, non-spillable, sealed, lead acid  
battery for years of dependable use. It was designed to be the most versatile and  
practical light for travel, camping, picnicking, tailgate parties and boating. Extremely  
rugged construction protects the unit from most vibration and shock damage.  
Un p a ck in g yo u r SLH1 0 0 V HID Sp o tlig h t  
The following items are included in the HID Spotlight package:  
WARN IN G: PLEASE  
INSPECT THE LIGHT  
FO R DAMAGE BEFO RE  
USE. IN THE CASE THAT  
DAMAGE IS FO UND,  
1 2 0 VO LT AC  
AN D 1 2 VO LT DC  
CHARGIN G  
ADAPTERS  
RETURN THE LIGHT FOR  
EXCHANGE.  
HID SPO TLIGHT  
FEATURES  
• Powerful, prefocused, high intensity discharge metal halide bulb  
Replaceable 7 Amp hour sealed lead acid battery  
• AC and DC recharge adapters  
• Adjustable carry strap  
• Protective safety guard (bezel) around lens  
• Hands-free adjustable work stand  
• Automatic charging (switches to float mode once fully charged)  
• Charging and full charge LED indicators  
Battery status indicator pushbutton  
4
 
Co n tro ls a n d Fu n ctio n s  
PO W ER SW ITCH  
ADJUSTABLE  
CARRY STRAP  
3 5 WATT 6 0 0 0 K  
METAL HALIDE  
BULB  
CO N VEN IEN T  
CARRY HAN DLE  
BATTERY STATUS  
IN DICATO R  
PUSHBUTTO N  
CHARGIN G/ PO W ER  
O N IN DICATO R  
FULL CHARGE  
IN DICATO R  
AC CHARGIN G PO RT  
TO UGH, DURABLE  
HO USIN G  
ADJUSTABLE  
W O RK STAN D  
CHARGIN G THE BATTERY  
The unit is delivered in a partially charged state. It must  
be fully charged prior to first use by using the 120 volt  
AC method.  
1 2 0 VO LT AC  
AN D 1 2 VO LT DC  
CHARGIN G  
After charging, disconnect the Adapter from the  
external power source, then disconnect the Adapter  
from the AC Recharge Port.  
ADAPTERS  
No te : Before charging/ recharging the units battery,  
make sure the power switch is in the OFF position.  
1 2 0 Vo lt AC Ch a rg in g / Re ch a rg in g  
Plug the supplied 120 Volt AC Adapters plug  
CHARGIN G/ PO W ER  
O N IN DICATO R  
FULL CHARGE  
IN DICATO R  
into a  
standard North American outlet.  
Connect the adapters DC pin into the AC  
Recharge Port located on the side of the unit,  
next to the Ba ttery Sta tus Indica tor. The  
Charging LED will light to indicate that the unit  
is charging. The Full Charge LED indicator will  
light green when the unit is fully charged.  
Note: When the unit is not charging and the  
Power Switch is engaged, the Charging/ ON LED  
will light blue.  
1 2 Vo lt DC Ch a rg in g / Re ch a rg in g  
The DC recharging method will NOT recharge the unit as effectively as the 120 volt  
AC method. The 12 volt DC recharging procedure is recommended only when it is  
necessary, since frequent use of the 12 volt DC recharging procedure may shorten  
the battery systems life.  
1. Insert the end plug of the12 Volt DC Adapter plug into the vehicles 12 volt DC  
accessory outlet.  
5
 
2. Insert the DC pin in the charging port on the side of the light.  
3. Charging time using this method is approximately 5 to 6 hours.  
4. When charging is complete, remove the power cord.  
Note: When using a vehicles 12 volt DC accessory outlet as a charging source, be  
aware that some vehicles require the ignition be turned on to power the accessory outlet.  
O PERATIN G IN STRUCTIO N S  
Usin g th e Sp o tlig h t  
The HID Spotlight is operated by the switch located on the handle of the unit. The  
Charging/ ON LED indicator will light blue when the unit is turned ON.  
Usin g th e Ad ju sta b le Wo rk Sta n d  
Set the hands-free adjustable work stand to the desired position; the stand will click  
into position.  
CARE AN D MAIN TEN AN CE  
CAUTIO N  
To re d uce th e risk o f b urn s a n d a vo id d a m a g e to th e un it, m a k e sure  
a ll p o w e r sw itch e s a re in th e O FF p o sitio n , a ll a d a p te rs a re un p lug g e d  
a n d th e un it h a s b e e n a llo w e d to co o l d o w n b e fo re re p la cin g th e  
b a tte ry a n d p e rfo rm in g a n y ca re a n d m a in te n a n ce o n th e e x te rio r o f  
th e lig h t.  
All batteries lose charge with time. AC recharge is recommended after each use or  
every two months when not in frequent use.  
If the unit gets dirty, gently clean the outer surfaces of the Spotlight with a soft cloth  
moistened with a mild solution of water and detergent. Periodically inspect the  
condition of recharge adapters, connectors, and wires. Replace any components  
that may have become worn or broken.  
Re p la ce m e n t Pa rts  
The sealed lead acid battery is the only user-replaceable part in this light and it is  
available through Vector Products, Inc. These can also be purchased from popular  
automotive parts suppliers nationwide. Contact Vector Products, Inc.s Technical  
Support Department for replacement parts (including replacement adapters and  
cords) and any additional information that you may need. They may be reached toll  
free at (800) 544-6986.  
6
 
Ba tte ry Re p la ce m e n t  
1. Remove screws and rotate the back cover counterclockwise.  
2. Pull out and remove the battery.  
3. Disconnect the terminals and replace the battery with the same type and size  
listed in the Specifications section in the back of this manual.  
4. Replace the battery compartment cover and screws.  
5. Turn the spotlights ON/ OFF switch to the ON position to ensure proper  
operation of spotlight.  
Sa fe Ba tte ry Disp o sa l  
Contains a maintenance-free, sealed, non-spillable, lead acid battery,  
which must be disposed of properly. Recycling is required, contact your  
local authority for information. Failure to comply with local, state and  
federal regulations can result in fines, or imprisonment. For more  
information on recycling this battery, call toll-free (877) 288-7722.  
Pro b le m  
Po ssib le Ca use  
Po ssib le so lutio n  
Internal battery power is Low. Turn switch OFF and using the battery status  
indicator, check for Low battery and if Low  
recharge the spotlight with either the AC or DC  
charging adapter provided.  
Switch is ON,  
Power LED is lit  
AND Spotlight  
will not light.  
Power was interrupted to  
the spotlight while the  
bulb was hot.  
A hot bulb may take up to 10 minutes to turn on  
following a power interruption. Turn switch OFF  
and wait 10 minutes for bulb to cool down before  
reusing the light  
AC or DC recharge adapter Turn switch OFF, unplug the recharge adapter  
is plugged into the light  
and then turn the switch back ON.  
Spotlight needs to be  
manually reset.  
Turn switch OFF wait 2s and turn the switch back  
ON. If problem persists return the spotlight to an  
authorized service center for repair.  
Spotlight is damaged.  
Turn switch OFF and return the spotlight to an  
authorized service center for repair.  
Vehicle ignition is not  
in Accessory position.  
On some vehicles the ignition must be in the  
accessory position to supply power to the 12V  
receptacles. Turn the vehicle ignition to the  
accessory position and try charging the  
spotlight again.  
Unit will not  
recharge.  
Poor DC plug connection  
Check DC adapter plug is well connected and  
try recharging the light.  
DC recharge adapter  
is damaged  
See an authorized service center to get a  
replacement DC recharge adapter.  
Poor 120V AC recharge  
adapter connection  
Check that the adapter is well connected to the  
120V AC outlet and to the light and try  
recharging the light.  
No power at the 120V  
AC outlet  
Try another 120V AC powered device in the  
outlet to see if it has power. If it does not the 120V  
AC circuit breaker may need to be reset. Contact  
a certified electrician if you are not comfortable  
resetting the 120V AC branch circuit.  
7
 
SPECIFICATIO N S  
Spotlight:  
6000 K 35 W Mh  
Input voltage:  
Output power:  
Input current:  
12V  
42w  
3.5A  
Batteries:  
12V 7Ah SLA  
AC Adapter:  
DC Adapter:  
Output:  
Input:  
13.8V 750 mA  
120V/ 60Hz 25w  
12 V  
8
 
O N E YEAR LIMITED WARRAN TY PRO GRAM  
This limited warranty program is the only one that applies to this product, and it sets forth all the  
responsibilities of Vector Products, Inc., regarding this product. There is no other warranty, other than  
those described herein. Any implied warranty of merchantability or fitness for a particular purpose on  
this product is limited in duration to the duration of this warranty.  
This Vector Products, Inc. product is warranted, to the original purchaser only, to be free of defects in  
materials and workmanship for one year from the date of purchase without additional charge. The  
warranty does not extend to subsequent purchasers or users. Manufacturer will not be responsible for  
any amount of damage in excess of the retail purchase price of the product under any circumstances.  
Incidental and consequential damages are specifically excluded from coverage under this warranty.  
This product is not intended for commercial use. This warranty does not apply to damage to units from  
misuse or incorrect installation/ connection. Misuse includes wiring or connecting to improper polarity  
power sources.  
RETURN/ REPAIR POLICY: Defective products may be returned to manufacturer. Any defective product  
that is returned to manufacturer within 30 days of the date of purchase will be replaced free of charge.  
If such a product is returned more than 30 days but less than one year from the purchase date,  
manufacturer will repair the unit or, at its option, replace it, free of charge.  
If the unit is repaired, new or reconditioned replacement parts may be used, at manufacturers option.  
A unit may be replaced with a new or reconditioned unit of the same or comparable design. The  
repaired or replaced unit will then be warranted under the terms of the remainder of the warranty  
period. The customer is responsible for the shipping charges on all returned items. During the warranty  
period, manufacturer will be responsible for the return shipping charges to the customer in the United  
States.  
LIMITATIONS: This warranty does not cover accessories, such as charging adapters, bulbs, fuses and  
batteries, damage or defects resulting from normal wear and tear (including chips, scratches, abrasions,  
discoloration or fading due to usage or exposure to sunlight), accidents, damage during shipping to our  
service facility, alterations, unauthorized use or repair, neglect, misuse, abuse, failure to follow  
instructions for care and maintenance, fire, flood and Acts of God.  
If your problem is not covered by this warranty, call our Technical Support Department toll free at (800)  
544-6986 for general repair information and charges if applicable.  
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations  
on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential  
damages, so the exclusions or limitations stated herein may not apply. This warranty gives the purchaser  
specific legal rights; other rights, which vary from state to state, may apply.  
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Technical Support by telephone, fax  
or mail (see below). We suggest that you keep the original packaging in case you need to ship the unit.  
When returning a product, include your name, address, phone number, dated sales receipt (or copy)  
and a description of the reason for return and product serial number. After repairing or replacing the  
unit, we will make every effort to return it to you within four weeks.  
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector Products, Inc.  
Enter “SLH100V as Model and “High Intensity Discharge Spotlight” as Product Type. All Vector  
Products, Inc. products must be registered within 30 days of purchase to activate this warranty. Mail the  
completed registration form, along with a copy of the original sales receipt, to:  
ATTN.: CUSTOMER SERVICE  
4409 W. Wanda, McAllen, TX 78503  
TOLL FREE: (800) 544-6986 • FAX: (956) 630-0492 •  
WARRANTY IS NON-TRANSFERABLE.  
RD040207  
© 2007 VECTOR PRODUCTS, INC.  
MADE IN CHINA  
11  
 

Tascam CD Player CC 222SLmkII User Manual
Tascam Computer Drive US 1800 User Manual
Taylor Thermometer 9867 User Manual
Toshiba Car Satellite Radio System Satellite U840W User Manual
Tricity Bendix Clothes Dryer TM 560 User Manual
Tricity Bendix Kitchen Entertainment Center HG210 User Manual
UNICOM Electric TV Converter Box GEP 5300TF C User Manual
Uniden Scanner UBC 2500XLT User Manual
ViewSonic Electronic Keyboard KU201 User Manual
Viking Oven F20554 EN User Manual