ViewSonic Flat Panel Television VX912 User Manual

®
ViewSonic  
VX912  
LCD Display  
- User Guide  
- Guide de l'utilisateur  
- Bedienungsanleitung  
- Guía del usuario  
- Guida dell'utente  
- Guia do usuário  
- Användarhandbok  
- Käyttöopas  
- Podręcznik użytkownika  
- Használati útmutató  
- Pyководство польэователя  
- Uživatelská píruka  
- ユーザーズイ ド  
- 使用手冊  
- 使用手冊  
- 사용자 안내서  
-
 
Compliance Information  
For U.S.A.  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation. This equipment generates,  
uses, and can radiate radio frequency energy, and if not installed and used in accordance with  
the instructions, may cause harmful interference to radio communications. However, there is  
no guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
FCC Warning  
To assure continued FCC compliance, the user must use grounded power supply cord and the  
cables which are included with the equipment or specified. Also, any unauthorized changes or  
modifications not expressly approved by the party responsible for compliance could void the  
user's authority to operate this device.  
For Canada  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing  
Equipment Regulations.  
Cet appareil numeique de la Classe B repecte toutes les exigences du Reglement sur le materiel  
brouilleur du Canada.  
CE Conformity for European Countries  
CE Conformity  
The device complies with the requirements of the EEC directive 89/336/EEC as  
amended by 92/31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic  
compatibility,” and 73/23/EEC as amended by 93/68/EEC Art.13 with regard to  
“Safety.”  
ViewSonic VX912  
1
 
Important Safety Instructions  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this unit near water.  
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s  
instructions.  
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other  
devices (including amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug  
has two blades with one wider than the other. A grounding type plug has two blades and a  
third grounding prong. The wide blade or the third prong are provided for your safety. If  
the provided plug does not fit into your outlet, consult an electrician for replacement of the  
obsolete outlet.  
10. Protect the power cord from being walked on or pinched particularly at plugs.  
Convenience receptacles and the point where they exit from the unit. Be sure that the  
power outlet is located near the unit so that it is easily accessible.  
11. Only use attachments/accessories specified by the manufacturer.  
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or  
sold with the unit. When a cart is used, use caution when moving the cart/unit combination  
to avoid injury from tip-over  
13. Unplug this unit when unused for long periods of time.  
14. Refer all servicing to qualified service personnel. Servicing is required when the unit has  
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been  
spilled or objects have fallen into the unit, the unit has been exposed to rain or moisture,  
does not operate normally, or has been dropped.  
ViewSonic VX912  
2
 
Copyright© ViewSonic Corporation, 2004. All rights reserved.  
Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.  
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of  
Microsoft Corporation in the United States and other countries.  
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered  
trademarks of ViewSonic Corporation.  
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and  
DDC are trademarks of VESA.  
ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency (EPA).  
As an ENERGY STAR® partner, ViewSonic Corporation has determined that this product meets  
the ENERGY STAR® guidelines for energy efficiency.  
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or  
omissions contained herein; nor for incidental or consequential damages resulting from  
furnishing this material, or the performance or use of this product.  
In the interest of continuing product improvement, ViewSonic Corporation reserves the right  
to change product specifications without notice. Information in this document may change  
without notice.  
No part of this document may be copied, reproduced, or transmitted by any means, for any  
purpose without prior written permission from ViewSonic Corporation.  
Product Registration  
To meet your future needs, and to receive any additional product information as it becomes  
available, please register your product on the Internet at: www.viewsonic.com. The  
ViewSonic® Wizard CD-ROM also provides an opportunity for you to print the registration  
form, which you may mail or fax to ViewSonic.  
For Your Records  
Product Name:  
Model Number:  
Document Number:  
Serial Number:  
Purchase Date:  
ViewSonic VX912  
VS10162  
VX912-2_UG_ENG Rev. 1A 11-15-04  
_____________________________  
_____________________________  
Product disposal at end of product life  
ViewSonic is concerned about the preservation of our environment. Please dispose of this  
product properly at the end of its useful life. For TCO'03 recycling information, please refer to  
our website:  
3. Taiwan: recycle.epa.gov.tw  
ViewSonic VX912  
3
 
Getting Started  
Congratulations on your purchase of a ViewSonic® LCD display.  
Important! Save the original box and all packing material for future shipping needs.  
NOTE: The word “Windows” in this user guide refers to the following Microsoft operating  
systems: Windows ‘95, Windows NT, Windows ‘98, Windows 2000, Windows Me  
(Millennium), and Windows XP.  
Package Contents  
Your LCD display package includes:  
• LCD display  
• Power cord  
• Video cable  
• ViewSonic Wizard CD-ROM  
NOTE: The CD jacket contains the Quick Start Guide, and the CD includes the User Guide  
PDF files and INF/ICM display optimization files. The INF file ensures compatibility with  
Windows operating systems, and the ICM file (Image Color Matching) ensures accurate on-  
screen colors. ViewSonic recommends that you install both files.  
Precautions  
• Sit at least 18” from your LCD display.  
your LCD display that prevents heat  
dissipation.  
Avoid touching the screen. Skin oils are  
difficult to remove.  
• Ensure the area around the LCD display is  
clean and free of moisture.  
Never remove the rear cover. Your LCD  
display contains high-voltage parts. You  
may be seriously injured if you touch  
them.  
• Do not place heavy objects on the LCD  
display, video cable, or power cord.  
• If smoke, abnormal noise, or strange odor  
is present, immediately switch the LCD  
display off and call your dealer or  
ViewSonic. It is dangerous to continue  
using the LCD display.  
• Avoid exposing your LCD display to direct  
sunlight or another heat source. Orient  
your LCD display away from direct  
sunlight to reduce glare.  
• Always handle your LCD display with  
care when moving it.  
• Do not rub or apply pressure to the LCD  
panel, as it may permanently damage the  
screen.  
• Place your LCD display in a well  
ventilated area. Do not place anything on  
ViewSonic VX912  
4
 
Quick Installation  
1. Remove two rear panel covers  
2. Connect power cord  
NOTE: If the CD-ROM does not auto-  
start: double-click on the CD-ROM icon in  
the Windows Explorer, then double-click  
on viewsonic.exe.  
3. Connect video cable  
• Make sure both the LCD display and  
computer are turned OFF  
• Follow the on-screen instructions.  
6. Windows users: Set the timing mode  
(resolution and refresh rate)  
• Connect the video cable from the LCD  
display to the computer  
Example: 1280 x 1024 @ 60 Hz.  
Macintosh users: Models older than G3  
require a Macintosh adapter. Attach the  
adapter to the computer and plug the video  
For instructions on changing the resolution  
and refresh rate, see the graphic card’s user  
guide.  
cable into the adapter.  
To order a ViewSonic® Macintosh adapter,  
contact ViewSonic Customer Support.  
Installation is complete. Enjoy your new  
ViewSonic, LCD display.  
To be best prepared for any future  
customer service needs: print this user  
guide and write the serial number in “For  
Your Records” on page 3. (See back of  
LCD display.)  
4. Turn ON LCD Display and computer  
Turn ON the LCD display, then turn ON  
the computer. This sequence (LCD display  
before computer) is important.  
You can register your product online at the  
website for your region. See the Customer  
Support table in this guide.  
NOTE: Windows users may receive a  
message asking them to install the INF  
file. This is on the CD.  
The ViewSonic Wizard CD-ROM also  
provides an opportunity for you to print  
the registration form which you may mail  
or fax to ViewSonic.  
5. Insert the ViewSonic Wizard CD into  
the computers CD drive.  
Follow the on-screen instructions. If your  
computer does not have a CD-ROM drive,  
see “Customer Support” on page 16.  
• Wait for the CD-ROM to auto-start.  
AC IN  
D-SUB  
Rear panel  
covers  
Power Code  
AC Outlet  
(Wall Socket)  
Computer Power Cord  
ViewSonic VX912  
5
 
Installation of Wall Mount (Optional)  
To obtain a wall-mounting kit, contact ViewSonic or your local dealer. Refer to the instructions  
that come with the base mounting kit. To convert your LCD display from a desk-mounted to a  
wall-mounted display, do the following:  
1. Disconnect Power.  
2. Lay the LCD display face down on a towel or blanket.  
3. Remove the Plastic Covers from the back of the LCD display.  
4. Remove the four screws attaching the base.  
5. Remove the Rubber Plugs from inside the four VESA screw holes.  
6. Attach the mounting bracket from the VESA compatible wall mounting kit (100 mm x 100  
mm distance).  
7. Attach the LCD display to the wall, following the instructions in the wall-mounting kit.  
Four vesa  
screw holes  
Plastic  
covers  
Rear panel  
covers  
Four base screws  
ViewSonic VX912  
6
 
Using the LCD Display  
Setting the Timing Mode  
Setting the timing mode is important for maximizing the quality of the screen image and  
minimizing eye strain. The timing mode consists of the resolution (example 1280 x 1024) and  
refresh rate (or vertical frequency; example 75 Hz). After setting the timing mode, use the  
OnView® controls to adjust the screen image.  
For the best picture quality set your LCD display timing mode to:  
VESA 1280 x 1024 @ 60Hz.  
To set the Timing Mode:  
1. Set the resolution: Right-click on the Windows desktop > Properties > Settings > set the  
resolution.  
2. Set the refresh rate: See your graphic card's user guide for instructions.  
WARNING: Do not set the graphics card in your computer to exceed the maximum refresh  
rate of 85Hz/1280 x 1024@75Hz; doing so may result in permanent damage to your LCD  
display.  
OSD and Power Lock Settings  
OSD Lock: Press and hold [1] and the up arrowSfor 10 seconds. If any buttons are pressed  
the message OSD Locked will display for few seconds.  
OSD Unlock: Press and hold [1] and the up arrowSagain for 10 seconds.  
Power Button Lock: Press and hold [1] and the down arrowTfor 10 seconds. If the power  
button is pressed the message Power Button Locked will display for few seconds. With or  
without this setting, after a power failure, your LCD display’s power will automatically turn  
ON when power is restored.  
Power Button Unlock: Press and hold [1] and the down arrowTagain for 10 seconds.  
ViewSonic VX912  
7
 
Adjusting the Screen Image  
Use the buttons on the front control panel to display and adjust the OnView® controls which  
display on the screen. The OnView controls are explained at the top of the next page and are  
defined in “Main Menu Controls” on page 10.  
Main Menu  
with OnView controls  
Front Control Panel  
shown below in detail  
Scrolls through menu options and adjusts the  
displayed control.  
Also a shortcut to display the Contrast adjustment  
control screen.  
Displays the Main  
Menu or exits the  
control screen  
and saves  
Displays the control screen for the  
highlighted control.  
Also toggles between two controls on  
some screens.  
adjustments.  
Also a shortcut to Auto Image Adjust.  
Power light  
Green = ON  
Orange = Power Saving  
Power On/Off  
ViewSonic VX912  
8
 
Do the following to adjust the screen image:  
1. To display the Main Menu, press button [1].  
NOTE: All OnView menus and adjustment screens disappear automatically after about 30  
seconds. This is adjustable through the OSD timeout setting in the setup menu.  
2. To select a control you want to adjust, pressSorTto scroll up or down the Main Menu.  
3. After the control is selected, press button [2]. A control screen like the one shown below  
appears.  
The line at the bottom of the screen tells  
you what you can do next: Exit or select the  
Brightness control.  
4. To adjust the control, press the upSor downTbuttons.  
5. To save the adjustments and exit the menu, press button [1] twice.  
The following tips may help you optimize your display:  
• Adjust your computer's graphic card so that it outputs a video signal 1280 x 1024 @ 60Hz  
to the LCD display. (Look for instructions on “changing the refresh rate” in your graphic  
card's user guide.)  
• If necessary, make small adjustments using H. POSITION and V. POSITION until the  
screen image is completely visible. (The black border around the edge of the screen should  
barely touch the illuminated “active area” of the LCD display.)  
ViewSonic VX912  
9
 
Main Menu Controls  
Adjust the menu items shown below by using the upSand downTbuttons.  
Control Explanation  
Auto Image Adjust automatically sizes, centers, and fine tunes the video signal  
to eliminate waviness and distortion. Press the [2] button to obtain a sharper  
image.  
NOTE: Auto Image Adjust works with most common video cards. If this  
function does not work on your LCD display, then lower the video refresh rate  
to 60 Hz and set the resolution to its pre-set value.  
Contrast adjusts the difference between the image background (black level)  
and the foreground (white level).  
Brightness adjusts background black level of the screen image.  
Color Adjust provides several color adjustment modes: preset color  
temperatures and RGB which allows you to adjust red (R), green (G), and blue  
(B) separately. The factory setting for this product is 6500K (6500 Kelvin).  
sRGB-RGB is quickly becoming the industry standard for color management,  
with support being included in many of the latest applications. Enabling this  
setting allows the LCD display to more accurately display colors the way they  
were originally intended. Enabling the sRGB setting will cause the Contrast and  
Brightness adjustments to be disabled.  
9300K-Adds blue to the screen image for cooler white (used in most office  
settings with fluorescent lighting).  
6500K-Adds red to the screen image for warmer white and richer red.  
5400K-Adds green to the screen image for a darker color.  
ViewSonic VX912  
10  
 
Control Explanation  
User Color Individual adjustments for red (R), green (G), and blue (B).  
1. To select color (R, G or B) press button [2].  
2. To adjust selected color, pressSorT.  
Important: If you select RECALL from the Main Menu when the product is set  
to a Preset Timing Mode, colors return to the 6500K factory preset.  
Information displays the timing mode (video signal input) coming from the  
graphics card in your computer, the LCD model number, the serial number, and  
the ViewSonic website URL. See your graphic cards user guide for instructions  
on changing the resolution and refresh rate (vertical frequency).  
NOTE: VESA 1280 x 1024 @ 60Hz (recommended) means that the resolution  
is 1280 x 1024 and the refresh rate is 60 Hertz.  
Manual Image Adjust displays the Manual Image Adjust menu.  
ViewSonic VX912  
11  
 
Control Explanation  
The Manual Image Adjust controls are explained below:  
H./V. Position (Horizontal/Vertical Position) moves the screen image left or  
right and up or down.  
H. Size (Horizontal Size) adjusts the width of the screen image.  
Fine Tune sharpens the focus by aligning the text and/or graphic characters.  
Sharpness adjusts the clarity and focus of the screen image.  
Setup menu displays the menu shown below:  
The Setup Menu controls are explained below:  
Language allows you to choose the language used in the menus and control  
screens.  
Resolution Notice displays the Resolution Notice menu shown below.  
Resolution Notice advises the optimal resolution to use.  
OSD Position allows you to move the on-screen display menus and control  
screens.  
ViewSonic VX912  
12  
 
Control Explanation  
OSD Timeout sets the length of time the on-screen display screen is displayed.  
For example, with a “15 second” setting, if a control is not pushed within 15  
seconds, the display screen disappears.  
OSD Background allows you to turn the On-Screen Display background On or  
Off.  
Memory Recall returns the adjustments back to factory settings if the display is  
operating in a factory Preset Timing Mode listed in the Specifications of this  
manual.  
Exception: This control does not affect changes made with the User Color  
control, Language and Power Lock setting.  
ViewSonic VX912  
13  
 
Other Information  
Specifications  
LCD  
Type  
19” (full 19" viewable diagonal area),  
TFT (Thin Film Transistor), Active Matrix SXGA LCD,  
0.294 mm pixel pitch  
Color Filter  
RGB vertical stripe  
Glass Surface  
Anti-Glare  
Input Signal  
Video Sync  
RGB analog (0.7/1.0 Vp-p, 75 ohms)  
Composite Sync, Separate Sync, Sync on Green  
f :24-82 kHz, f :50-85 Hz  
h
v
Compatibility  
Resolution  
PC  
Up to 1280 x 1024 Non-interlaced  
Power Macintosh up to 1280 x 1024  
1
Macintosh  
Recommended  
and supported  
1280 x 1024 @ 60, 75 Hz  
1024 x 768 @ 60, 70, 72, 75, 85 Hz  
800 x 600 @ 56, 60, 72, 75, 85 Hz  
640 x 480 @ 60, 75, 85 Hz  
720 x 400 @ 70 Hz  
1280 x 1027 @60 Hz (720p)  
HDTV  
Power  
Voltage  
Full Scan  
100-240 VAC, 50/60 Hz (auto switch)  
Display area  
376.32mm (H) x 301.6mm (V)  
14.8" (H) x 11.9" (V)  
Operating  
conditions  
Temperature  
Humidity  
32° F to + 104° F (0° C to + 40° C)  
10% to 90% (no condensation)  
To 10,000 feet  
Altitude  
Storage  
Temperature  
Humidity  
-4° F to + 140° F (-20° C to + 60° C)  
10% to 90% (no condensation)  
To 40,000 feet  
conditions  
Altitude  
Dimensions  
Weight  
Physical  
431 mm (W) x 469 mm (H) x 201 mm (D)  
17.0" (W) x 18.5" (H) x 7.9" (D)  
(LCD display only)  
Net  
14.8 lb (6.7 kg)  
(LCD display only)  
Regulations  
VCCI, BSMI, PSB, C-Tick,  
CE, GS, Ergo, TCO'99, PCT,  
®
CCC, UL/cUL, FCC-B, ICES, NOM, TUV-S, ENERGY STAR  
Power saving  
modes  
On  
Off  
Normal  
<1W  
(green LED)  
(orange LED)  
®
Preset Timing Mode (pre-adjusted to VESA 1280 x 1024 @ 60 Hz)  
Warning: Do not set the graphics card in your computer to exceed these refresh rates; doing so may result in  
permanent damage to the LCD display.  
1
Macintosh computers older than G3 require a ViewSonic® Macintosh adapter. To order an  
adapter, contact ViewSonic.  
ViewSonic VX912  
14  
 
Troubleshooting  
No power  
• Make sure power button (or switch) is ON.  
• Make sure A/C power cord is securely connected to the LCD display.  
• Plug another electrical device (like a radio) into the power outlet to verify that the outlet is  
supplying proper voltage.  
Power is ON but no screen image  
• Make sure the video cable supplied with the LCD display is tightly secured to the video  
output port on the back of the computer. If the other end of the video cable is not attached  
permanently to the LCD display, tightly secure it to the LCD display.  
• Adjust brightness and contrast.  
• If you are using an Macintosh older than G3, you need a Macintosh adapter.  
Wrong or abnormal colors  
• If any colors (red, green, or blue) are missing, check the video cable to make sure it is  
securely connected. Loose or broken pins in the cable connector could cause an improper  
connection.  
• Connect the LCD display to another computer.  
• If you have an older graphics card, contact ViewSonic for a non-DDC adapter.  
Control buttons do not work  
• Press only one button at a time.  
ViewSonic VX912  
15  
 
Customer Support  
For technical support or product service, see the table below or contact your reseller.  
NOTE: You will need the product serial number.  
T = Telephone  
F = FAX  
Country/Region Website  
Email  
T= (800) 688 6688  
F= (909) 468 1202  
United States  
Canada  
T= (886) 463 4775  
F= (909) 468 1202  
T= (0800) 833 648  
F= +44 (0) 1293 643 910  
Europe, Middle  
East, Baltic  
countries, and  
(Contact your reseller)  
North Africa  
T=+ 61 2 9906 6277  
F=+ 61 2 9906 6377  
Australia and  
New Zealand  
Singapore,  
Southeast Asia, www.viewsonic.com.sg  
and India  
T=+ 65 273 4018  
F=+ 65 273 1566  
T=+886 (2) 2246 3456  
F=+886 (2) 8242 3668  
South Africa and  
other countries  
T=+886 (2) 2246 3456  
F=+886 (2) 8242 3668  
Hong Kong  
ViewSonic VX912  
16  
 
Cleaning the LCD Display  
• MAKE SURE THE LCD DISPLAY IS TURNED OFF.  
• NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE.  
To clean the screen:  
1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.  
2. If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner  
onto a clean, soft, lint-free cloth, and wipe the screen.  
To clean the case:  
1. Use a soft, dry cloth.  
2. If still not clean, apply a small amount of a non-ammonia, non-alcohol based, mild non-  
abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.  
Disclaimer  
• ViewSonic does not recommend the use of any ammonia or alcohol-based cleaners on the  
LCD display screen or case. Some chemical cleaners have been reported to damage the  
screen and/or case of the LCD display.  
• ViewSonic will not be liable for damage resulting from use of any ammonia or alcohol-  
based cleaners.  
ViewSonic VX912  
17  
 
Limited Warranty  
VIEWSONIC LCD DISPLAY  
What the warranty covers:  
®
ViewSonic warrants its products to be free from defects in material and workmanship during the warranty period. If a product  
proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or  
replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or  
components.  
How long the warranty is effective:  
ViewSonic LCD displays are warranted for three (3) years for all parts including the light source and three (3) years for all  
labor from the date of the first consumer purchase.  
Who the warranty protects:  
This warranty is valid only for the first consumer purchaser.  
What the warranty does not cover:  
1. Any product on which the serial number has been defaced, modified or removed.  
2. Damage, deterioration or malfunction resulting from:  
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure  
to follow instructions supplied with the product.  
b. Repair or attempted repair by anyone not authorized by ViewSonic.  
c. Any damage of the product due to shipment.  
d. Removal or installation of the product.  
e. Causes external to the product, such as electrical power fluctuations or failure.  
f. Use of supplies or parts not meeting ViewSonic’s specifications.  
g. Normal wear and tear.  
h. Any other cause which does not relate to a product defect.  
3. Removal, installation, and set-up service charges.  
How to get service:  
1. For information about receiving service under warranty, contact ViewSonic Customer Support. You will need to provide  
your product's serial number.  
2. To obtain service under warranty, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your  
address, (d) a description of the problem, and (e) the serial number of the product.  
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic.  
4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.  
Limitation of implied warranties:  
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION  
CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE.  
Exclusion of damages:  
VIEWSONIC'S LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE  
PRODUCT. VIEWSONIC SHALL NOT BE LIABLE FOR:  
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES BASED UPON  
INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS  
OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COM-  
MERCIAL LOSS, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.  
3. ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.  
Effect of state law:  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do  
not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the  
above limitations and exclusions may not apply to you.  
Sales outside the U.S.A. and Canada:  
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact ViewSonic or  
your local ViewSonic dealer.  
ViewSonic LCD Warranty (V3.0)  
ViewSonic VX912  
18  
 
 

Tatung Network Card TVA 171 User Manual
Tech Craft TV Video Accessories XLN62 User Manual
Tektronix Marine Radio CSA 803C User Manual
Toshiba CRT Television 26AF45C User Manual
Toshiba Power Supply RMTI EMD HT User Manual
Trane Refrigerator CG PRC011 EN User Manual
Tripp Lite Fan MKH 800 P 48 User Manual
Tripp Lite TV Cables B125 101 60 User Manual
Verbatim Computer Drive 8cm DVD User Manual
Viper Automobile Alarm Model 160XV User Manual