Vision Fitness Bicycle E3600iNetTV User Manual

A s s e m b l y  
G u i d e  
E3600iNetTV  
COMMERCIAL FITNESS BIKE  
 
TOOLS & PARTS INCLUDED  
MM  
Screwdriver  
15 Pedal Wrench  
MM  
5 Allen Wrench  
PARTS BOX  
Console Mast Cover, Qty: 1  
Water Bottle & Cage, Qty: 1  
Heart Rate Chest Strap, Qty: 1  
Color-coded Hardware Bags  
Assembly Guide  
CONSOLE BOX  
iNetTV Console  
Owners Guide  
Warranty Card  
 
HARDWARE INCLUDED  
ORANGE BAG  
PINK BAG  
M8 x 65L Screw  
Quantity: 2  
M8 x 20L Screw  
Quantity: 2  
M8 Lock Washer  
Quantity: 4  
M8 x 20L Screw  
Quantity: 2  
M8 Lock Washer  
Quantity: 2  
BLUE BAG  
M8 Lock Washer  
Quantity: 6  
M8 x 15L Screw  
Quantity: 7  
 
STEP  
1
ORANGE BAG  
• Install the rear foot with the four lock  
washers (M8), two inside screws  
(M8x65L), and two outside screws  
STEP  
1
MM  
(M8x20L). Tighten with the 5 Allen  
wrench.  
5
 
STEP  
2
BLUE BAG  
STEP  
2
• Slide the rubber boot onto the  
console mast.  
• Locate the bundle of wires that  
comes from the bracket on top of the  
bike frame. Wrap these wires with the  
wire tie coming from the bottom of the  
console mast. Pull the wire tie and  
bundle of wires up through the top of  
the console mast while simultaneously  
sliding the mast into the frame  
bracket.  
• Secure the console mast to the  
frame bracket with six lock washers  
(M8) and six screws (M8x15L).  
MM  
Tighten with the 5 Allen wrench.  
Place the seventh screw (M8x15L) in  
the rear of the frame bracket and  
tighten until snug.  
• Slide the console mast boot down  
and snap it into place on the side  
cover.  
• Remove the nuts (M8) from the  
screws on the bottom of the seat.  
Attach the seat to the seat post with  
the nuts you just removed. Tighten with  
MM  
the 15 wrench.  
• Loosen the seat post knob and slide  
the seat post into place in the seat  
tube bracket.  
6
 
STEP  
3
PINK BAG  
• Feed the heart rate wires from the  
handlebars through the small hole  
located in the front of the console  
mast. Pull these wires up through the  
hole at the top of the console mast.  
Attach the handlebar to the console  
mast using two lock washers (M8)  
and two screws (M8x20L). Tighten  
STEP  
3
MM  
with the 5 Allen wrench.  
7
 
STEP  
4
CONSOLE  
• Remove the six mounting screws  
from the back of the console with the  
Phillips screwdriver. Set the console in  
place and secure it to the console  
mast with the screws you just  
removed. Connect all the wires to the  
proper locations in the back of the  
console (see diagram).  
STEP  
4
• With the Phillips screwdriver remove  
the two screws located half way up  
the console mast. Attach the water  
bottle bracket to the console mast with  
the two screws. Insert the water bottle.  
1 - Co-Axial Cable TV  
2 - USB - B  
3 - USB - A  
1
2
3
4
5
6
7
8
4 - VGA (PC Video)  
5 - Video IN  
6 - Audio - R  
7 - Audio - L  
9
WIRES  
8 - Microphone  
9 - Heart Rate Reciever 1  
10 - Heart Rate Reciever 2  
11 - 20 Pin Connector  
12 - Power Plug  
10  
12  
13  
11  
13 - Miles/Kilometers Switch  
14 - Data Port  
14  
500 South CP Avenue  
P.O. Box 280  
Lake Mills. WI 53551  
fax 1.920.648.3373  
toll free 1.800.335.4348  
phone 1.920.648.4090  
2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z36CB40-AG1824PRD  
AG18.24PRD  
REV1  
8
 

Toastmaster Slow Cooker TSC3W User Manual
Toastmaster Toaster WT75G WT75B User Manual
ToCAD Camcorder Accessories 9002TM User Manual
Toshiba Blu ray Player BDX3000KU User Manual
Toshiba DVD Player SD390EKB User Manual
Toshiba Personal Computer PSAG9X User Manual
Toshiba Security Camera IK WB30A User Manual
Toshiba TV DVD Combo 32LV17U User Manual
Tricity Bendix Dishwasher BDW 10 User Manual
Tyco Electronics Radio MM23016 User Manual