Vizio Battery Charger VEC080 User Manual

VEC080  
2 AMP/1AMP  
BATTERY CHARGER  
IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR VECTOR  
PURCHASE CALL TOLL FREE (866) 584-5504. IN MOST CASES A  
VECTOR SERVICE REPRESENTATIVE CAN RESOLVE  
YOUR PROBLEM OVER THE PHONE.  
KEY INFORMATION YOU SHOULD  
KNOW:  
• Quick Disconnect Harness  
• Two-Stage Charging  
• DC Accessory Plug  
• Battery Terminal Rings  
• Battery Clips  
BEFORE RETURNING THIS PRODUCT FOR ANY  
REASON, PLEASE CALL TOLL FREE (866) 584-5504  
OWNER’S MANUAL AND  
WARRANTY INFORMATION  
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY,  
OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. READ  
CAREFULLY BEFORE USE, AND RETAIN FOR FUTURE REFERENCE.  
4140 S.W. 28th Way, Ft. Lauderdale, FL 33312  
Toll Free: (866) 584-5504  
 
PERSONAL PRECAUTIONS SAFETY  
1. Another person should be within range of your voice or close enough to come to  
your aid when you work near a lead-acid battery.  
2. Fresh water and soap should be nearby in case battery acid contacts skin, cloth-  
ing, or eyes.  
3. Wear complete eye protection and clothing protection. Avoid touching eyes while  
working with a battery. Acid, acid particles or corrosion may get into eyes.  
Immediately flood eye with cold water (Eye Wash Station) for at least 10 minutes  
and seek medical attention immediately.  
4. If battery acid contacts skin or clothing, wash immediately with soap and water.  
5. NEVER smoke or allow a spark or flame in vicinity of battery or engine.  
CAUTION: Dropping a metal tool onto battery might spark or short-circuit battery or  
other electrical part that may cause explosion.  
6. Remove personal metal items such as rings, bracelets, necklaces, and watches  
when working with a lead acid battery. A lead-acid battery can produce a short-  
circuit current high enough to cause a severe burn.  
AC POWER CORD CONNECTION  
Charger is equipped with an AC cord with a "polarized" plug. The plug must be  
plugged into a properly installed 110/120VAC polarized outlet in accordance with  
all local codes and ordinances. This battery charger is for use with a 110/120VAC  
polarized plug ONLY.  
DANGER: NEVER alter AC cord or plug – if it will not fit outlet, have proper outlet  
installed by a qualified electrician. Improper connection may result in an  
electric shock, and will void warranty.  
PREPARING TO CHARGE  
1. Determine voltage of battery by referring to car owner's manual.  
2. If it is necessary to remove battery from vehicle to charge, or to clean terminals,  
always remove grounded terminal from battery first. Make sure all accessories in  
the vehicle are off, so as not to cause an arc.  
3. Clean battery terminals. Do not allow corrosion to come in contact with eyes.  
4. Add distilled water in each cell until battery acid reaches level specified by bat-  
tery manufacturer. This helps purge excessive gas from cells. Do not overfill. For  
a battery without cell caps (maintenance free), carefully follow manufacturer's  
charging instructions.  
5. Study all battery manufacturers' specific precautions, such as removing or not  
removing cell caps, while charging and recommended rates of charge.  
6. Area around battery should be well ventilated while battery is being charged.  
7. Make sure the initial charging rate does not exceed battery manufacturers’  
requirement.  
2
 
CHARGER LOCATION  
1. Locate charger as far away from battery as cables permit.  
2. NEVER place charger directly above battery being charged; gases from battery  
will corrode and damage charger.  
3. NEVER allow battery acid to drip on charger when reading specific gravity or fill-  
ing battery.  
4. NEVER operate charger in a closed-in area or restrict ventilation in any way.  
5. Marine batteries must be removed and charged on shore.  
6. Do not set a battery on top of charger.  
DC CONNECTION PRECAUTIONS  
1. Connect and disconnect DC output clamps only after removing AC cord from  
electric outlet.  
2. Never allow clamps to touch each other.  
3. Attach clamps to battery posts and check for secure connection. This will hold  
clamps securely on terminals and helps to reduce risk of sparking.  
FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE. A SPARK  
NEAR BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE RISK OF A  
SPARK NEAR BATTERY:  
1. Position AC and DC cords to reduce risk of damage by hood, door, or moving  
engine part.  
2. Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to  
persons.  
3. Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has  
larger diameter than NEGATIVE (NEG, N,-) post.  
4. For negative-grounded vehicle, connect POSITIVE (RED) clamp from battery  
charger to POSITIVE (POS, P, +) post of battery. Connect NEGATIVE (BLACK)  
clamp to vehicle chassis or engine block away from battery. Do not connect clip  
to carburetor, fuel lines, or sheet-metal body parts. Connect to heavy gauge metal  
part of the frame or engine block.  
5. For positive-grounded vehicle, connect NEGATIVE (BLACK) clamp from battery  
charger to NEGATIVE (NEG, N, -) ungrounded post of battery. Connect POSITIVE  
(RED) clamp to vehicle chassis or engine block away from battery. Do not connect  
clip to carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gauge  
metal part of the frame or engine block.  
6. When disconnecting charger, turn switches to off, disconnect AC cord, remove  
clamp from vehicle chassis, and then remove clamp from battery terminal.  
7. See operating instructions for length of charge information.  
8. Do not charge the battery while the engine is operating.  
3
 
INTRODUCTION  
Thank you for selecting the Vector Battery Charger (VEC080). With proper care and  
use, it will give you years of dependable service. Please read and observe all safety  
warnings and cautions and this entire users manual, before installing or using this  
device. The manual should then be retained for quick reference whenever the unit is  
used. Figure 1 shows the battery charger and its components.  
FEATURES  
• The unit has two Charge Rate settings, controlled by one switch:  
a) 2 amp: for recharging motorcycles, lawn mowers, tractors, ATVs, snowmobiles  
and personal watercraft.  
b) 1 amp: for maintenance charging RVs, speciality vehicles, antique and classic  
cars, marine deep cycle batteries and more.  
• Maintains battery charge in stored vehicles  
• Excellent for winter pre-start battery warm-up.  
• Includes three connector sets:  
a) DC accessory plug.  
b) Battery harness clips.  
c) Battery ring terminal harness.  
• Charging indicators:  
a) Red - bad connection, battery not able to accept charge, reverse polarity  
hook-up.  
b) Yellow - connection correct and charging.  
c) Green - fully charged.  
• UL-Listed for safety  
• Fully automatic; powers on when needed, powers off when battery is fully-charged  
or topped-off  
• Built-in circuit protection guards against overcharging or short circuit  
• Automatically checks for correct polarity (requires a minimum of 4.0 volts battery  
voltage)  
• Convenient, color-coded ring terminals/clamps for easy, correct installation.  
• Charges with high frequency, pure, DC current.  
4
 
1/2 Amp Battery Charger  
110/120 Volt AC Plug End  
Cables  
Accessory Outlet  
DC Accessory Plug  
Battery Harness  
Clips  
Battery  
Battery Terminal  
Rings  
Chassis  
Battery  
FIGURE 1. 2 Amp Battery Charger Connection Diagram  
CONNECTING THE CHARGER WITH THE TERMINAL CLIPS  
The chargers output leads have color-coded battery clips  
(Figure 2) (RED-POSITIVE and BLACK-NEGATIVE). These  
connect directly to the corresponding connectors on the  
battery posts.  
Black  
1. Position the RED clip on the terminal of the POSITIVE  
battery post connector.  
2. Position the BLACK clip on the NEGATIVE post  
connector.  
Red  
3. Simply plug the AC plug of the AC/DC  
adapter/charger into any standard 110/120 volt  
AC wall outlet to begin charging.  
FIGURE 2. Battery Clips  
4. When charging is complete and the FULL light is on, remove the charger and  
store in a safe place.  
5
 
Nut  
Terminal Rings  
Bolt  
Connector  
FIGURE 3. - Ring Terminal Connection Diagram  
NOTE: ALWAYS disconnect the AC power cord from the AC power outlet before con-  
necting (or disconnecting) the charger to (or from) the battery.  
CONNECTING THE CHARGER WITH TERMINAL RINGS  
The chargers output leads have crimped, color-coded  
ring terminals (Figure 4) (RED-POSITIVE and BLACK-  
Black  
NEGATIVE). These rings connect directly to the corre-  
sponding connectors on the battery posts.  
1. Remove the nuts from the bolts of the battery posts  
Red  
connectors.  
2. Position the RED terminal on the bolt of the POSI-  
TIVE battery post connector.  
FIGURE 4. Terminal Rings  
3. Position the BLACK terminal on the NEGATIVE post  
connector; then replace the nuts. (Figure 3)  
4. If there is any problem connecting the output leads, check with a reputable auto  
supply store or contact the Customer Service Department toll free (866) 584-  
5504 for assistance in finding an appropriate connection device for your par-  
ticular application.  
6
 
CONNECTING THE CHARGER WITH THE DC ACCESSORY PLUG  
The chargers output leads also contain a DC acces-  
sory plug (Figure 5).  
1. Plug DC plug into vehicles DC accessory outlet.  
2. Plug the AC plug of the charger into any stan-  
dard 110/120 volt AC wall outlet.  
NOTE: The 12 volt DC recharging procedure is rec-  
ommended only when it is necessary, as con-  
tinued use of the 12 volt DC recharging pro-  
cedure may shorten the battery systems life .  
FIGURE 5. DC Accessory Plug  
If unit is fully discharged, it is recommended that the vehicle being used for recharging be  
left running while the unit is being charged via the 12 volt DC method.  
MAINTENANCE  
With proper care and minimal maintenance, the Vector® Battery Charger will pro-  
vide years of dependable service. For maximum performance, Vector® recommends:  
1. Storing the unit in a clean, dry, cool place when not in use.  
2. Cleaning the unit casing and cords (as necessary) with a dry (or slightly damp)  
cloth. Ensure that unit is completely disconnected from battery and power  
source, before cleaning.  
3. To maintain the operating condition and maximize the life of the charger cords,  
always coil them loosely for storage. Do not wrap them around the unit or crimp  
them with a tight band.  
SPECIFICATIONS  
Input:...............................................120V AC 0.5 amps  
Output:............................................Nominal 12 volt DC at up to 2 amperes  
Reverse Polarity Protection ................Output battery clips short circuit protection  
Bulk Charge.....................................2 amps constant current raises battery voltage  
until it reaches 14.4V +/- 0.2V  
Absorption.......................................Constant- holds voltage 14.4V +/- 0.2V and  
forces the current to fully charge the battery  
Float................................................When battery falls below 12.8V +/- 0.2V the  
charger will start charging from Bulk Charge  
stage again.  
7
 
TROUBLESHOOTING  
NOTE: Ensure that all installation and operating instructions and safety  
precautions are understood and carefully followed by anyone installing or  
using the charger. Refer to the following chart for some typical operating prob-  
lems and recommended actions:  
Charging Indicators  
Red LED  
Bad connection, battery not able to accept charge, reverse polarity  
connection  
Yellow LED  
Green LED  
Connection correct and charging.  
Battery fully charged.  
NOTE: When the charger is properly connected, the green LED will illuminate, indi-  
cating the inside smart circuit is functioning to judge the battery status. This  
procedure may take up to 2 minutes if the battery is lower than 12.8 volts.  
• Check that the correct charge rate has been selected for the battery being  
charged.  
• If the battery to be charged has fallen below 4 volts, the battery cannot be  
re-charged with this unit.  
VERY COLD BATTERY  
If the battery to be charged is extremely cold (in temperatures less than freezing -  
0º C/32º F) it cannot accept a high rate of charge, so the initial charge rate will be  
slow. The rate of charge will increase as the battery warms.  
CAUTION: Any changes or modifications not expressly approved by the party  
responsible for compliance could void the users authority to operate the  
equipment.  
NOTE: This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to part 15 of the FCC Rules. This limits are  
designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particu-  
lar installation. If equipment does cause harmful interference to radio or tele-  
vision reception, which can be determined by turning the equipment off and  
on, the user is encouraged to try to correct the interference by one or more  
of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
8
 
2 YEAR LIMITED WARRANTY PROGRAM  
This limited warranty program is the only one that applies to this product, and it sets forth all the  
responsibilities of Vector Manufacturing, Ltd., regarding this product. There is no other warranty,  
other than those described herein.  
This Vector Manufacturing, Ltd. product is warranted, to the original purchaser only, to be free of  
defects in materials and workmanship for two years from the date of purchase without additional  
charge. The warranty does not extend to subsequent purchasers or users. Vector Manufacturing,  
Ltd. will not be responsible for any amount of damage in excess of the retail purchase price of the  
product under any circumstances. Incidental and consequential damages are specifically excluded  
from coverage under this warranty.  
This product is not intended for commercial use. This warranty does not apply to accessories or dam-  
age to units from misuse or incorrect installation. Misuse includes wiring or connecting to improper  
polarity power sources.  
RETURN/REPAIR POLICY: Defective products, other than accessories, may be returned postage pre-  
paid to Vector Manufacturing. Any defective product, other than accessories, that is returned to  
Vector Manufacturing within 30 days of the date of purchase will be replaced free of charge. If  
such a product is returned more than 30 days but less than two years from the purchase date,  
Vector Manufacturing will repair the unit or, at its option, replace it free of charge.  
If the unit is repaired, new or reconditioned replacement parts may be used, at Vector  
Manufacturings option. A unit may be replaced with a new or reconditioned unit of the same or  
comparable design. The repaired or replaced unit will then be warranted under the terms of the  
remainder of the warranty period. The customer is responsible for the shipping charges on all  
returned items after 30 days. During the warranty period, Vector Manufacturing, Ltd. will be respon-  
sible for the return shipping charges.  
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting  
from normal wear and tear (including chips, scratches, abrasions, discoloration or fading due to  
usage or exposure to sunlight), accidents, damage during shipping to our service facility, alterations,  
unauthorized use or repair, neglect, misuse, abuse, failure to follow instructions for care and main-  
tenance, fire, flood and Acts of God.  
If your problem is not covered by this warranty, call our Technical Support Department at (954) 584-  
4446 or Toll Free at (866) 584-5504 for general repair information and charges if applicable. You  
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations  
on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential  
damages, so the exclusions or limitations stated herein may not apply. This warranty gives the pur-  
chaser specific legal rights; other rights, which vary from state to state, may apply.  
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Vector Manufacturing Technical Support by  
telephone, fax or mail. We suggest that you keep the original packaging in case you need to ship  
the unit. When returning a product, include your name, address, phone number, dated sales receipt  
(or copy) and a description of the reason for return and product serial number. After repairing or  
replacing the unit, we will make every effort to return it to you within four weeks.  
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector  
Manufacturing. Enter “VEC080” as Model and “2 Amp Battery Charger” as Product Type. All  
Vector Manufacturing, Ltd. products must be registered within 10 days of purchase to activate  
this warranty. Mail the completed registration form, along with a copy of the original sales receipt  
to:  
ATTN.: CUSTOMER SERVICE / VECTOR MANUFACTURING, Ltd.  
4140 SW 28th Way, Ft. Lauderdale, FL 33312  
PH: 954-584-4446 • TOLL FREE: 866-584-5504 • Fax: 954-584-5556.  
WARRANTY IS NON-TRANSFERABLE AND NON-REFUNDABLE.  
DS041204  
9
 

THB Bury Automobile Accessories LT 9100 User Manual
Tiger Games 65 122 User Manual
Toastmaster Convection Oven RA 5T User Manual
Tricity Bendix Refrigerator TB 57 L User Manual
True Fitness Treadmill Z54 User Manual
Vestax CD Player CDX 15 User Manual
Viking Oven DEDO User Manual
Vivitek DVD VCR Combo DVD Combo User Manual
Vivotek Home Security System FD8167 T User Manual
Watlow Electric Electric Heater FREEZE SAFE User Manual