Vizio Computer Accessories N 8510MS User Manual

INSTALLATION MANUAL  
IP STANDARD MASTER STATION N-8510MS  
Thank you for purchasing TOA's IP Standard Master  
Station.  
Please carefully follow the instructions in this manual to  
ensure long, trouble-free use of your equipment.  
1. SAFETY PRECAUTIONS  
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe  
operation.  
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or  
cautions regarding safety.  
• After reading, keep this manual handy for future reference.  
Indicates a potentially hazardous situation which, if mishandled, could  
result in moderate or minor personal injury, and/or property damage.  
CAUTION  
When the Unit is in Use  
• Use the dedicated AC adapter or its equivalent for the unit. Note that the use of other adapter may cause a  
fire.  
2. GENERAL DESCRIPTION  
The N-8510MS is an IP standard master station designed for use with TOA's packet intercom N-8000 system (IP network-  
compatible intercom system) that employs the packet audio technology*.  
By directly connecting the N-8510MS to a network (LAN or WAN), high quality hands-free or handset conversations  
between IP stations, and paging broadcasts (paging calls) can be made. Once an emergency message has been  
programmed into the station, it can be broadcast to the pre-programmed zones with the key operation or external control  
input.  
The ideal system for in-house or wide-area information transmission applications such as conversations between IP  
stations and N-8000 system's stations, paging broadcasts (paging calls), periodical broadcasts, and background music  
broadcasts can be built in conjunction with the N-8000EX or N-8010EX IP intercom exchange, or the N-8000MI Multi  
interface unit.  
Using an optional YC-280 Wall mounting bracket, the station can be mounted on a wall, or tilted for easy key operation  
when used on a desktop.  
* Technology related to audio transmission over a network.  
Warning  
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may  
be required to take adequate measures.  
 
6. WALL MOUNTING  
The optional YC-280 Wall mounting bracket is required.  
The YC-280 can be mounted to a one-gang electrical box.  
6.1. Mounting  
YC-280 Wall mounting  
bracket (optional)  
Step 1. Install the YC-280 to the wall.  
N-8510MS  
Notes  
• Use the appropriate screws for the construction  
of wall.  
Wall  
surface  
• Wood screws 3.5 x 20 are supplied with the  
YC-280.  
• No fitting screws for an electrical box are  
supplied.  
Use commercially available screws.  
2
Step 2. Hang the station on the wall mounting bracket  
hook to install.  
1
Hook  
Push down the station body in the arrow  
direction shown at right.  
Wood screw 3.5 x 20  
(supplied with the YC-280)  
6.2. Installation Completion Drawing  
6.3. YC-280 Dimensional Drawing  
Unit: mm  
Unit: mm  
148  
4.6 x 6  
Rubber foot mounting position  
(desktop application)  
2-ø4.5  
60  
YC-280  
80  
72.1  
83.5  
4.5 x 10  
YC-280  
100  
7. DESKTOP INSTALLATION  
The station can be used on a desk. In desktop installations, the front operation panel can be inclined 16˚ from the desk  
surface for easier operation by attaching the YC-280 Wall mounting bracket to its bottom surface.  
7.1. Attaching the Bracket  
7.2. Installation Completion Drawing  
Unit: mm  
Step 1. Attach the four rubber feet to the YC-280's bottom surface.  
205.2  
Step 2. Hang the YC-280's hook on the station's wall bracket  
mounting slot to install.  
Push up the YC-280 in the arrow direction shown below.  
N-8510MS  
YC-280 Wall mounting bracket  
YC-280  
Rubber foot  
(supplied with the YC-280)  
Hook  
 
8. WIRING  
[Power supply connection]  
N-8510MS rear  
The following 2 methods are available for  
supplying power to the station.  
• From a DC 12 V AC adapter  
• From an IEEE802.3af compliant PoE  
switching hub  
DC INPUT  
CONTACT IN  
LAN  
(For connection, refer to the instruction  
manual supplied with the switching hub.)  
C
H
12V  
400mA  
Cable  
[AC adapter connection]  
1
Connect the AC adapter* .  
Install the supplied ferrite  
clamp on the AC adapter  
cable by winding the  
cable around the ferrite  
clamp once.  
Ferrite clamp (accessory)  
1
* Use the AC adapter AD-1210P (optional) or its equivalent.  
As for the usable adapter, consult your TOA dealer.  
To network  
[Network connection]  
[Control line connection]  
Can be connected to a network of  
10BASE-T/100BASE-TX in auto-sensing.  
Use a UTP category 5 straight-through  
cable with an RJ-45 connector for this  
connection.  
Connect the external control equipment such  
as a switch or sensor to this terminal.  
Press down the desired push-in  
terminal button with a tip of standard  
driver, and insert the cable securely.  
Note  
When using a PoE hub, be sure to  
connect equipment having a protective  
earth terminal (or power cable with earth)  
and ground the earth terminal. Failure to  
do so may cause equipment malfunction.  
11 mm  
• Applicable cables are as follows.  
COM  
HOT  
Conductor diameter:  
ø0.4 – 1.3 mm (AWG16 – 26), Solid wire  
ø0.7 – 1.4 mm (AWG16 – 22), Stranded wire  
9. ACCESSORIES  
10. OPTIONAL PRODUCTS  
CD*2 .................................................. 1  
Ferrite clamp ..................................... 1  
AC adapter:  
Wall mounting bracket: YC-280  
AD-1210P*3  
*2 Contains the N-8000 setting software program and the  
N-8000 series instruction manual.  
*3 Consult your TOA dealer when using an equivalent  
adapter.  
The Setup Launcher is automatically started when the  
supplied CD-ROM is inserted into the PC's drive.  
Note  
If your PC's CD drive is not compatible with the  
AutoRun function, the setup guide is not automatically  
started even when the CD is inserted.  
Traceability Information for Europe  
(EMC directive 2004/108/EC)  
Use either "Explorer" or "My Computer" to execute the  
following files, or use [Start  
enter the following command.  
Manufacturer:  
TOA Corporation  
7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo, Japan  
Run] in the Task Bar and  
Authorized representative:  
TOA Electronics Europe GmbH  
Suederstrasse 282, 20537 Hamburg, Germany  
<Drive where CD is placed> \index.html  
For example, when the CD is placed in the "d" drive,  
d:\index.html  
133-06-295-10  
 

Teac Clock Radio SLD80R User Manual
Teac Electronic Accessory LP R550USB User Manual
Teledyne Carbon Monoxide Alarm gfc 7000ta User Manual
Timex Clock Radio T436 User Manual
Toshiba DVD Player SD7200 User Manual
Toshiba Personal Computer Tecra A6 EZ6312 User Manual
Triarch Indoor Furnishings 75362 10 User Manual
Turbo Air Freezer TGF 23F User Manual
United States Stove Gas Heater VF30IL User Manual
ViewSonic Computer Monitor E70f+ User Manual