User’s Manual
High Force 3 Ice Power
Subwoofer
We thank you very much for purchasing a Waterfall High Force Subwoofer. Our deliberate
choice for aesthetics and performance is constantly guiding our research and development
towards innovative technologies. In order to achieve the best performance with your Home
Cinema system, we recommend you read carefully the following set up instructions.
In order to achieve the best acoustical performance, the HF3 IP Evo,
ideally has to be positioned near an angle/corner in the room.
A) Functions & Set up of HF3 IP’s Amplifier
Warning :
Check the mains voltage selector (N°1) position (115V/230V) and use the correct voltage for your country before connecting the
mains plug. Changing the fuse : In the event of complete failure, first disconnect the powers cable from the mains, then check the
mains fuse.When replacing the fuse, only use a fuse which is absolutely identical to the original one. If this does not solve the
problem, contact your dealer.
• Only the subwoofer is to be connected to the mains supply. Never plug your speakers directly into the main power supply.
• Before proceeding with any connection, make sure that all your equipment is switched off.
• Before switching it on, please ensure that the "level" button (N°4) is on minimum.
•YourWaterfall Speakers are to be directly connected to the speaker output socket on your amplifier or A/VProcessor.
• Also ensure that the polarities are correct : + ( red ) and - ( black ).
• Do not expose this product to heat and humidity.
Mains voltage selector (115V/230V)
2 Fuse
1
13
10
9
8
7
6
5
4
LEVEL
Control panel
AUTO
12dB
LFE 24dB ON
DIRECT 1
VENTED
OFF
FREQ
PHASE
SUB FULL CLOSED
DIRECT
3
4
5
6
7
Main power switch (on - off)
Level :Volume adjustment of the integrated amplifier.
Phase :Alows you to adjust phase from 0 to 180°.
Freq :Adjustment of the frequency cut off, from 40 to 150Hz.
PRT : Standby LED indicates unit in standby mode with power connec-
ted.When the Sub is activated this standby LED is off and the Logo LED
lights up. Flashes in case of default.
On – Auto – Off : Recommended Setting should be : "Auto", so when
not in use for a while, amplifier goes back into standby, if "On" position
is used,this means the amplifier will continuously be on,and will not go
into standby.
40
150 0°
180°
0
MAX
Hz
LOW LEVEL INPUT
11
Mains cord
(supplied)
L
R
DIRECT 1
DIRECT 2
+
-
12
8
9
14
HI-LEVEL INPUT
SUBWOOFER
S300
ATOHM®
24-12-LFE :Switching of the active filter of the Sub.The choice of 24Db
per octave or 12Db per octave is to be determined through listening
and personal choice.
Main power
switch
(on - off)
3
OFF
ON
Factory settings. DO NOT CHANGE.
10
11
2
Low Level Input/Output :The "audio" signals are transmitted by a cinch
cable (supplied by our retailer) linking the "subwoofer Pre-out" of the
processor to one of the "Line in" of the Sub, (either white or red entry).
"High Level Input" :To be used only with conventional
stereo amplifiers.
DO NOT OPEN NE PAS OUVRIR
/
1
RISK OF ELECTRIC SHOCK
DANGER D'ELECTROCUTION
115V/60Hz 360W
115V
230V
:
:
FUSE T3.15AL
FUSE T1.60AL
Fuse
230V/50Hz T 360W
DESIGNED IN FRANCE TECHNOLOGIE FRANÇAISE
/
12
13
The subwoofer MUST be connected to the mains with the
enclosed connector cord.The main switch has to be on "on"
position and the (N°8) switch "on-auto-off" in the "auto"
position.Your HF3 IP Subwoofer is equipped with a wide range
of connection options for Hi Fi or AudiVideo, Home Cinema.
Input selector (for specific set up).
14 Connections for specific use.
|