Weed Eater Blower 530165291 01 User Manual

R
Trademark  
Instruction Manual  
Manual de Instrucciones  
Manuel d’Instructions  
B1750 LE  
IMPORTANT MANUAL - Do not throw away  
MANUAL IMPORTANTE - No lo descarte  
MANUEL IMPORTANT - À Conserver  
WARNING:  
Read and follow all Safety Rules and Operating Instructions before  
using this product. Failure to do so can result in serious injury.  
ADVERTENCIA:  
Lea el manual de instrucciones y siga todas las advertencias e  
instrucciones de seguridad. El no hacerlo puede resultar en lesiones  
graves.  
AVERTISSEMENT:  
Veuillez lire le manuel d’instructions et bien respecter tous les  
avertissements et toutes les instructions de sécurité. Tout défaut  
de le faire pourrait entraîner des blessures graves.  
Electrolux Home Products, Inc.  
104 Warren Road  
Augusta, GA 30907  
Copyright E2004 Electrolux Home Products, Inc.  
530165291-01  
6/28/04  
 
weather has beenlinked to blood vesseldam-  
age in otherwise healthy people. If symptoms  
occur such as numbness, pain, loss of  
strength, change in skin color or texture, or  
loss of feeling in the fingers, hands, or joints,  
discontinue the use of this tool and seek  
medical attention. An antivibration system  
does not guarantee the avoidance of these  
problems. Users who operate power tools on  
a continual and regular basis must monitor  
closely their physical condition and the condi-  
tion of this tool.  
MAINTAIN YOUR UNIT PROPERLY  
D Have all maintenance other than the rec-  
ommended procedures described in the in-  
struction manual performed by an autho-  
rized service dealer.  
D Disconnect spark plug before performing  
maintenance except for carburetor adjust-  
ments.  
D Use only recommended Weed EaterŽ re-  
placement parts; use of any other parts  
may void your warranty and cause damage  
to your unit.  
D Empty fuel tank before storing the unit. Use  
up fuel left in carburetor by starting engine and  
letting it run until it stops.  
D Do not use any accessory or attachment  
other than those recommended by manufac-  
turer for use with your unit.  
D Do not store the unit or fuel in a closed area  
where fuel vapors can reach sparks or an  
open flame from hot water heaters, electric  
motors or switches, furnaces, etc.  
D Store in a dry area out of reach of children.  
SPECIAL NOTICE: Exposure to vibra-  
tions through prolonged use of gasoline pow-  
ered hand tools could cause blood vessel or  
nerve damage in the fingers, hands, and  
joints of people prone to circulation disorders  
or abnormal swelling. Prolonged use in cold  
SPECIAL NOTICE: This unit is equipped  
with a temperature limiting muffler and spark  
arresting screen which meets the require-  
ments of California Codes 4442 and 4443. All  
U.S. forest land and the states of California,  
Idaho, Maine, Minnesota, New Jersey, Ore-  
gon, and Washington require by law that  
many internal combustion engines be  
equipped witha spark arresting screen. If you  
operatein alocalewhere such regulations ex-  
ist, you are legally responsible for maintaining  
the operating condition of these parts. Failure  
to do so is a violation of the law. Refer to the  
MAINTENANCE section for information on  
maintenance of the muffler and spark arrest-  
ing screen.  
ASSEMBLY  
NOTE: Knob must be loose enough to allow  
blower tube to be inserted in blower outlet.  
Loosen knob by turning counterclockwise.  
WARNING: This unit is intended for  
blower use only. Do not attempt to open inlet  
cover. Openedor damaged inlet cover can re-  
sult in serious injury. Discontinue use of blow-  
er immediately if inlet cover becomes opened  
or damaged. Take unit to your nearest autho-  
rized service dealer for repair.  
Blower  
Blower  
Outlet  
Tube  
WARNING: If you receive your unit  
assembled, check each step to insure your  
unit is properly assembled and all fasteners  
are secure. Follow all safety information in  
the manual and on the unit.  
BLOWER TUBE ASSEMBLY  
1. Align the rib on the blower tube with the  
groove in the blower outlet; slide the tube  
into place.  
Groove  
Rib  
2. Secure the tube by turning the knob clock-  
wise.  
3. To remove the tube, turn the knobcounter-  
clockwise to loosen the tube; remove the  
tube.  
-- 3 --  
 
OPERATION  
KNOW YOUR BLOWER  
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.  
Compare the illustrations with your unit to familiarize yourself with the location of the various controls  
and adjustments. Save this manual for future reference.  
Primer Button  
Choke Lever  
Fuel Mix  
Throttle  
Fill Cap  
Lever  
Starter  
Rope  
Spark Plug  
Blower  
Tube  
Rear  
Handle  
THROTTLE LEVER  
CHOKE LEVER  
The THROTTLE LEVER is used to select the  
desired engine speed and to stop the engine.  
The CHOKE helps to supply fuel to the engine  
to aid in cold starting. Activate the choke by  
moving the choke lever to the FULL CHOKE  
position. After engine attempts to start, move the  
choke lever to the HALF CHOKE position.  
Once engine starts, move choke lever to the  
RUN position.  
Movethethrottlelever to the  
full speed operation. Move the throttle lever  
position for  
to the  
positionfor idlespeed. To stop the  
engine, move the throttle lever to the STOP  
position.  
PRIMER BUTTON  
The PRIMER BUTTON removes air from the  
carburetor and fuel lines and fills them with fuel.  
This allows you to start the engine with fewer  
pulls on the starter rope. Activate primer button  
by pressing it and allowing it to return to its origi-  
nal position.  
S Operate power equipment only at reasonable  
hours--not early in the morning or late at night  
when people might be disturbed. Comply with  
times listed in local ordinances. Usual recom-  
mendations are 9:00 a.m. to 5:00 p.m.,  
Monday though Saturday.  
OPERATING POSITION  
Eye  
Protection  
S To reduce noise levels, limit the number of  
pieces of equipment used at any one time.  
S To reduce noise levels, operate power  
blowers at the lowest possible throttle  
speed to do the job.  
S Use rakes and brooms to loosen debris be-  
fore blowing.  
S In dusty conditions, slightly dampen sur-  
faces or use a mister attachment when wa-  
ter is available.  
Blower  
OPERATING TIPS  
S While blowing debris, hold the unit with the  
muffler side facing away from your body  
and clothes (see OPERATING POSITION  
illustration above).  
S To reduce the risk of hearing loss  
associated with sound level(s), hearing  
protection is required.  
S To reduce the risk of injury associated with  
contacting rotating parts, stop the engine be-  
fore installing or removing attachments. Do  
not operate without guard(s) in place.  
S Conserve water by using power blowers  
instead of hoses for many lawn and garden  
applications, including areas such as gutters,  
screens, patios, grills, porches, and gardens.  
S Watch out for children, pets, open windows,  
or freshly washed cars. Blow debris away  
safely.  
S Use the full blower nozzle extension so the  
air stream can work close to the ground.  
-- 4 --  
 
S After using blowers and other equipment,  
CLEAN UP! Dispose of debris in trash re-  
ceptacles.  
TO STOP THE ENGINE  
D To stop the engine, move the throttle lever  
to the STOP position.  
BEFORE STARTING ENGINE  
BEFORE STARTING THE ENGINE  
WARNING: Be sure to read the fuel  
information in the safety rules before you be-  
gin. If you do not understand the safety rules,  
do not attempt to fuel your unit. Call  
1-800-554-6723.  
WARNING: You MUST make sure  
the tubes are secure before using the unit.  
D
Fuel engine. Move at least 10 feet (3 me-  
ters) away from the fueling site.  
Hold the unit in the starting position as  
shown. Make sure the blower end is di-  
rected away from people, animals, glass,  
and solid objects.  
D
FUELING ENGINE  
WARNING: Remove fuel cap slowly  
when refueling.  
This engine is certified to operate on unleaded  
gasoline. Before operation, gasoline must be  
mixed with a good quality synthetic 2-cycle  
air-cooled engine oil designed to be mixed at a  
ratio of 40:1. Poulan/Weed Eater brand  
synthetic oil is recommended. Mix gasoline and  
oil at a ratio of 40:1. A 40:1 ratio is obtained by  
mixing 3.2 ounces (95 ml) of oil with 1 gallon (4  
liters) of unleaded gasoline. DO NOT USE  
automotive oil or boat oil. These oils will cause  
engine damage. When mixing fuel, follow  
instructions printed on container. Once oil is  
added to gasoline, shake container momentarily  
to assure that the fuel is thoroughly mixed.  
Always read and follow the safety rules relating  
to fuel before fueling your unit.  
STARTING POSITION  
WARNING: When starting engine,  
hold the unit as illustrated. Do not set unit on any  
surface except a clean, hard area when starting  
engine or while engine is running. Debris such  
as gravel, sand, dust, grass, etc. could be  
picked up by the air intake and thrown out  
through the discharge opening, damaging the  
unit or property, or causing serious injury to by-  
standers or the operator.  
IMPORTANT  
Experience indicates that alcohol blended  
fuels (called gasohol or using ethanol or  
methanol) can attract moisture which leads to  
separation and formation of acids during  
storage. Acidic gas can damage the fuel  
system of an engine while in storage. Toavoid  
engine problems, empty the fuel system  
before storage for 30 days or longer. Drain the  
gas tank, start theengine and let it run until the  
fuel lines and carburetor are empty. Use fresh  
fuel next season. Never use engine or  
carburetor cleaner products in the fuel tank or  
permanent damage may occur.  
STARTING A COLD ENGINE  
1. Move throttle lever to the  
position.  
2. Move choke lever to the FULL CHOKE  
position.  
3. Slowly press the primer button 8 times.  
T
NOTE: Unit must be placed on its side when  
adding fuel (see illustration below).  
Choke Lever  
4. Pull starter rope sharply until engine at-  
tempts to run, but nomore than 5 pulls (be-  
low 30_ F, 8 pulls).  
NOTE: If engine attempts to start before the  
th  
5
pull, go to next step immediately.  
5. Move the choke lever to the HALF  
CHOKE position.  
6. Pull the starter rope sharply until the en-  
gine runs, but no more than 5 pulls (below  
30_ F, 10 pulls).  
7. After a 5 second warm--up, move the  
choke lever to the RUN position.  
8. Allow the unit to run for 30 more seconds  
at the RUN position before moving the  
throttle lever to  
position.  
-- 5 --  
 
If engine has not started after 5 pulls (at HALF  
CHOKE), repeat STARTING A COLD ENGINE  
procedure. If engine still does not start, proceed  
to STARTING A FLOODED ENGINE.  
9. To stop the engine, move the throttle lever to  
the STOP position.  
STARTING A WARM ENGINE  
NOTE: If fuel tank is empty, add fuel; then,  
follow STARTING A COLD ENGINE proce-  
dure. Do not fill fuel tank while engine is hot.  
3. To stop the engine, move the throttle lever to  
the STOP position.  
STARTING A FLOODED ENGINE  
Flooded engines can be started by placing the  
choke lever in the RUN position. Move throttle  
lever to the fast position  
; then, pull rope  
until engine starts. After engine starts, move the  
throttle lever to the slow position  
engine to idle.  
to allow  
Starting could require pulling the starter rope  
many times depending on how badly the unit is  
flooded.  
1. Move throttle lever to the  
position.  
2. Pull starter rope sharply until engine runs,  
but no more than 5 pulls.  
If unit still doesn’t start refer to the TROUBLE-  
SHOOTING TABLE or call 1-800-554-6723.  
NOTE: If engine has not started, pull starter  
rope 5 more pulls. If engine still does not run,  
it is probably flooded.  
MAINTENANCE  
CLEAN AIR FILTER  
WARNING: Avoid touching muffler  
unless engine and muffler are cold. A hot  
muffler can cause serious burns.  
Air Filter  
Cover  
WARNING: This unit is intended for  
blower use only. Do not attempt to open inlet  
cover. Openedor damaged inlet cover can re-  
sult in serious injury. Discontinue use of blow-  
er immediately if inlet cover becomes opened  
or damaged. Take unit to your nearest autho-  
rized service dealer for repair.  
GENERAL RECOMMENDATIONS  
The warranty on this unit does not cover items  
that have been subjected to operator abuse  
or negligence. To receive full value from the  
warranty, the operator must maintain unit as  
instructed in this manual. Various adjust-  
ments will need to be made periodically to  
properly maintain your unit.  
CHECK FOR LOOSE  
FASTENERS AND PARTS  
S Spark Plug Boot  
S Air Filter  
S Housing Screws  
S Muffler  
Screws  
Air Filter  
Cleaning the air filter:  
A dirty air filter decreases engine perform-  
ance and increases fuel consumption and  
harmful emissions. Always clean or replace  
air filter after every 5 hours of operation or  
yearly, whichever comes first.  
1. Clean the cover and the area around it to  
keep debris from falling into the carburetor  
chamber when the cover is removed.  
2. Remove parts as illustrated.  
NOTE: Do not clean filter in gasoline or other  
flammable solvent. Doing so can create a fire  
hazard or produce harmful evaporative emis-  
sions.  
CHECK FOR DAMAGED OR WORN  
PARTS  
Contact an authorized service dealer for re-  
placement of damaged or worn parts.  
S Throttle Lever -- Ensure throttle lever func-  
tions properly by moving the throttle lever to  
the STOP position. Make sure engine  
stops; then restart engine and continue.  
S Fuel Tank -- Do not use unit if fuel tank shows  
signs of damage or leaks.  
3. Wash the filter in soap and water.  
4. Allow filter to dry.  
5. Apply a few drops of oil to the filter;  
squeeze filter to distribute oil.  
6. Replace parts.  
REPLACE SPARK PLUG  
INSPECT AND CLEAN UNIT AND  
DECALS  
Replace spark plug each year to ensure the  
engine starts easier and runs better. Set  
spark plug gap at 0.025 inch. Ignition timing is  
fixed, nonadjustable.  
S After each use, inspect complete unit for  
loose or damaged parts. Clean the unit and  
decals using a damp cloth with a milddeter-  
gent.  
1. Twist, then pull off spark plug boot.  
2. Remove spark plug from cylinder and dis-  
card.  
S Wipe off unit with a clean dry cloth.  
3. Replace with Champion RCJ-6Y spark  
plug and tighten securely with a 3/4 inch  
socket wrench.  
4. Reinstall the spark plug boot.  
-- 6 --  
 
As the unit is used, carbon deposits build up  
on the muffler and spark arresting screen,  
and must be removed to avoid creating a fire  
hazard or affecting engine performance.  
REPLACE FUEL FILTER  
Toreplace fuel filter, drain unit by running it dry  
of fuel, then remove fuel cap/retainer assem-  
bly from tank. Pull filter from tank and remove  
it fromthe fuel line. Install new fuelfilter on fuel  
line; reinstall parts.  
VIEW OF MUFFLER  
Spark arresting  
screen  
Fuel Line  
Exhaust  
Diverter  
Screws  
Fuel Filter  
CHECK MUFFLER MOUNTING  
SCREWS  
Replace the spark arresting screen every 50  
hours of operation or if any damage or breaks  
in the screen are noted.  
Once each year, ensure muffler mounting  
screws are secure and tightened properly to  
prevent damage.  
NOTE: Do not attempt to clean the spark ar-  
Mounting  
Screw  
resting screen.  
1. Loosen and remove the 2 screws from the  
muffler cover. Remove the muffler cover.  
2. Loosen and remove both screws from the  
exhaust diverter.  
Holes  
Muffler Cover  
3. Remove the exhaust diverter and spark  
arresting screen.  
4
Install new spark arresting screen.  
5. Reinstall exhaust diverter and both  
screws. Tighten screws securely.  
6. Reinstall muffler cover and 2 screws.  
Tighten securely.  
Screws  
NOTE: If any part of the muffler is cracked,  
broken or damaged, we recommend that the  
muffler be replaced.  
1. Loosen and remove the 2 screws from the  
muffler cover.  
2. Remove the muffler cover.  
3. Tighten the 2 muffler mounting screws se-  
curely.  
CARBURETOR ADJUSTMENT  
There is no screw for idle adjustment on your  
blower. The throttle lever is used to control  
engine speed. The throttle lever can be  
placed in one of four positions: STOP, IDLE  
4. Reinstall muffler cover and 2 screws.  
Tighten securely.  
INSPECT MUFFLER AND SPARK  
ARRESTING SCREEN  
or  
, FULL THROTTLE or  
, and one  
intermittent position. If your enginewill not run  
properly or you require further assistance,  
contact an authorized service dealer or call  
1--800--554--6723.  
WARNING: The muffler on this prod-  
uct contains chemicals known to the State of  
California to cause cancer.  
STORAGE  
SEASONAL STORAGE  
WARNING: Perform the following  
steps after each use:  
Prepare unit for storage at end of season or if  
it will not be used for 30 days or more.  
If your unit is to be stored for a period of time:  
S Clean the entire unit before lengthy stor-  
age.  
S Allow engine to cool, and secure the unit  
before storing or transporting.  
S Store unit and fuel in a well ventilated area  
where fuel vapors cannot reach sparks or  
open flames from water heaters, electric  
motors or switches, furnaces, etc.  
S Store unit with all guards in place. Position  
unit so that any sharp object cannot acci-  
dentally cause injury.  
S Store in a clean dry area.  
S Lightly oil external metal surfaces.  
FUEL SYSTEM  
Under FUELING ENGINE in the OPERA-  
TION section of this manual, see message la-  
beled IMPORTANT regarding the use of ga-  
sohol in your engine.  
S Store unit and fuel well out of the reach of  
children.  
-- 7 --  
 
Fuel stabilizer is an acceptable alternative in  
minimizing the formation of fuel gum deposits  
during storage. Add stabilizer to gasoline in fuel  
tank or fuel storage container. Follow the mix  
instructions found on stabilizer container. Run  
engine at least 5 minutes after adding stabilizer.  
S Clean air filter.  
S Check entire unit for loose screws, nuts,  
and bolts. Replace any damaged, broken,  
or worn parts.  
S At the beginning of the next season, use  
only fresh fuel having the proper gasolineto  
oil ratio.  
ENGINE  
S Remove spark plug and pour 1 teaspoon of  
40:1, 2-cycle engine oil (air cooled) through  
the spark plug opening. Slowly pull the  
starter rope 8 to 10 times to distribute oil.  
S Replace spark plug with new one of recom-  
mended type and heat range.  
OTHER  
S Do not store gasoline from one season to  
another.  
S Replace your gasoline can if it starts to rust.  
TROUBLESHOOTING TABLE  
WARNING: Always stop unit and disconnect spark plug before performing any of the  
recommended remedies below other than remedies that require operation of the unit.  
TROUBLE  
Engine will not  
start.  
CAUSE  
1. Engine flooded.  
REMEDY  
1. See “Starting a Flooded Engine”  
in Operation section.  
2. Fill tank with correct fuel mixture.  
3. Install new spark plug.  
2. Fuel tank empty.  
3. Spark plug not firing.  
4. Fuel not reaching  
carburetor.  
4. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
5. Contact an authorized service dealer.  
5. Compression low.  
1. Fuel not reaching  
1. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
Engine will not  
idle properly.  
carburetor.  
2. Carburetor requires  
adjustment.  
3. Crankshaft seals worn.  
4. Compression low.  
2. Contact an authorized service dealer.  
3. Contact an authorized service dealer  
4. Contact an authorized service dealer.  
1. Clean or replace air filter.  
2. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
1. Air filter dirty.  
2. Fuel not reaching  
carburetor.  
Engine will not  
accelerate,  
lacks power, or  
dies under a  
load.  
3. Clean or replace spark plug  
and re-gap.  
3. Spark plug fouled.  
4. Contact an authorized service dealer.  
4. Carburetor requires  
adjustment.  
5. Carbon build up.  
6. Compression low.  
5. Contact an authorized service dealer.  
6. Contact an authorized service dealer.  
1. Choke partially on.  
1. Adjust choke.  
Engine smokes  
excessively.  
2. Fuel mixture incorrect.  
2. Empty fuel tank and refill with  
correct fuel mixture.  
3. Air filter dirty.  
4. Carburetor requires  
adjustment.  
3. Clean or replace air filter.  
4. Contact an authorized service dealer.  
Engine runs hot.  
1. See “Fueling Engine” in Operation  
section.  
1. Fuel mixture incorrect.  
2. Replace with correct spark plug.  
3. Contact an authorized service dealer.  
2. Spark plug incorrect.  
3. Carburetor requires  
adjustment.  
4. Contact an authorized service dealer.  
4. Carbon build up.  
-- 8 --  
 
LIMITED WARRANTY  
ELECTROLUX HOME PRODUCTS, INC.,  
cover predelivery setup or normal adjustments  
warrants to the original purchaser that each  
new Weed Eaterr brand gasoline tool or at-  
tachment is free from defects in material and  
workmanship and agrees to repair or replace  
under this warranty any defective gasoline  
product or attachment as follows from the  
original date of purchase:  
explained in the instruction manual.  
THIS WARRANTY GIVES YOU SPECIFIC  
LEGAL RIGHTS, AND YOU MAY HAVE  
OTHER RIGHTS WHICH VARY FROM  
STATE TO STATE.  
NO CLAIMS FOR CONSEQUENTIAL OR  
OTHER DAMAGES WILL BE ALLOWED,  
AND THERE ARE NO OTHER EXPRESS  
WARRANTIES EXCEPT THOSE EX-  
PRESSLY STIPULATED HEREIN.  
SOME STATES DO NOT ALLOW LIMITA-  
TIONS ON HOW LONG AN IMPLIED WAR-  
RANTY LASTS OR THE EXCLUSION OR  
LIMITATIONS OF INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES, SO THE ABOVE  
LIMITATIONS OR EXCLUSION MAY NOT  
APPLY TO YOU.  
The policy of ELECTROLUX HOME PROD-  
UCTS, INC., is to continuously improve its prod-  
ucts. Therefore, ELECTROLUX HOME  
PRODUCTS, INC., reserves the right to  
change, modify, or discontinue models, de-  
signs, specifications, and accessories of all  
products at any time without notice or obligation  
to any purchaser.  
2 YEARS - Parts and Labor, when used for  
household purposes.  
90 DAYS - Parts and Labor, when used for  
commercial, professional, or income producing  
purposes.  
30 DAYS - Parts and Labor, if used for rental  
purposes.  
This warranty is not transferable and does not  
cover damage or liability caused by improper  
handling, improper maintenance, or the use of  
accessories and/or attachments not specifically  
recommended by ELECTROLUX HOME  
PRODUCTS, INC., for this tool. Additionally,  
this warranty does not cover tune-ups, spark  
plugs, filters, starter ropes, starter springs, cut-  
ting line, or rotating head parts that will wear and  
require replacement with reasonable use during  
the warranty period. This warranty does not  
U.S. EPA/CALIFORNIA  
EMISSION CONTROL WARRANTY STATEMENT  
YOUR WARRANTY RIGHTS AND OBLIGA-  
TIONS: The U.S. Environmental Protection  
Agency/California Air Resources Board and  
ELECTROLUX HOME PRODUCTS, INC., are  
pleased to explain the emissions control system  
warranty on your year 2002--2004 small off--  
road engine. In California, all new small off--road  
engines must be designed, built, and equipped  
to meet the State’s stringent anti--smog stan-  
dards. ELECTROLUX HOME PRODUCTS,  
INC., must warrant the emission control system  
on your small off--road engine for the periods of  
time listed below provided there has been no  
abuse, neglect, or improper maintenance of  
your small off--road engine engine. Your emis-  
sion control system includes parts such as the  
carburetor and the ignition system. Where a  
warrantable condition exists, ELECTROLUX  
HOME PRODUCTS, INC., will repair your small  
off--road engine engine at no cost to you. Ex-  
penses covered under warranty include diagno-  
sis, parts and labor. MANUFACTURER’S  
WARRANTY COVERAGE: If any emissions  
related part on your engine (as listed under  
Emissions Control Warranty Parts List) is defec-  
tive or a defect in the materials or workmanship  
of the engine causes the failure of such an emis-  
sion related part, the part will be repaired or re-  
placed by ELECTROLUX HOME PROD-  
UCTS, INC. OWNER’S WARRANTY RE-  
SPONSIBILITIES: As the small off--road en-  
gine engine owner, you are responsible for the  
performance of the required maintenance listed  
in your instruction manual. ELECTROLUX  
HOME PRODUCTS, INC., recommends that  
you retain all receipts covering maintenance on  
your small off--road engine, but ELECTROLUX  
HOME PRODUCTS, INC., cannot deny war-  
ranty solely for the lack of receipts or for your  
failure to ensure the performance of all sched-  
uled maintenance. As the small off--road en-  
gine engine owner, you should be aware that  
ELECTROLUX HOME PRODUCTS, INC.,  
may deny you warranty coverage if your small  
off--road engine engine or a part of it has failed  
due to abuse, neglect, improper maintenance,  
unapproved modifications, or the use of parts  
not made or approved by the original equipment  
manufacturer. You are responsible for present-  
ing your small off--road engine to an ELECTRO-  
LUX HOME PRODUCTS, INC., authorized re-  
pair center as soon as a problem exists. War-  
ranty repairs should be completed in a reason-  
able amount of time, not to exceed 30 days. If  
you have any questions regarding your warran-  
ty rights and responsibilities, you should contact  
your nearest authorized service center or call  
ELECTROLUX HOME PRODUCTS, INC., at  
1--800--554--6723.  
WARRANTY  
COM-  
MENCEMENT DATE: The warranty period be-  
gins on the date the small off--road engine is  
purchased. LENGTH OF COVERAGE: This  
warranty shall be for a period of two years from  
the initial date of purchase. WHAT IS COV-  
ERED: REPAIR OR REPLACEMENT OF  
PARTS. Repair or replacement of any war-  
ranted part will be performed at no charge to the  
owner at an approved ELECTROLUX HOME  
PRODUCTS, INC., servicing center. If you  
have any questions regarding your warranty  
rights and responsibilities, you should contact  
your nearest authorized service center or call  
-- 9 --  
 
ELECTROLUX HOME PRODUCTS, INC., at  
1--800--554--6723 WARRANTY PERIOD: Any  
warranted part which is not scheduled for re-  
placement as required maintenance, or which is  
scheduled only for regular inspection to the ef-  
fect of “repair or replace as necessary” shall be  
warranted for 2 years. Any warranted part which  
is scheduled for replacement as required main-  
tenance shall be warranted for the period of time  
up to the first scheduled replacement point for  
that part. DIAGNOSIS: The owner shall not be  
charged for diagnostic labor which leads to the  
determination that a warranted part is defective  
if the diagnostic work is performed at an ap-  
proved ELECTROLUX HOME PRODUCTS,  
INC., servicing center. CONSEQUENTIAL  
DAMAGES: ELECTROLUX HOME PROD-  
UCTS, INC., may be liable for damages to other  
engine components caused by the failure of a  
warranted part still under warranty. WHAT IS  
NOT COVERED: All failures caused by abuse,  
neglect, or improper maintenance are not cov-  
ered. ADD-ON OR MODIFIED PARTS: The  
use of add--on or modified parts can be grounds  
for disallowing a warranty claim. ELECTRO-  
LUX HOME PRODUCTS, INC., is not liable to  
cover failures of warranted parts caused by the  
use of add--on or modified parts. HOW TO FILE  
A CLAIM: If you have any questions regarding  
your warranty rights and responsibilities, you  
should contact your nearest authorized service  
center or call ELECTROLUX HOME PROD-  
UCTS, INC., at 1--800--554--6723. WHERE TO  
GET WARRANTY SERVICE: Warranty ser-  
vices or repairs shall be provided at all ELEC-  
TROLUX HOME PRODUCTS, INC., service  
centers. call: 1--800--554--6723 MAINTE-  
NANCE, REPLACEMENT AND REPAIR OF  
EMISSION RELATED PARTS: Any ELEC-  
TROLUX HOME PRODUCTS, INC., approved  
replacement part used in the performance of  
any warranty maintenance or repair on emis-  
sion related parts will be provided without  
charge to the owner if the part is under warranty.  
EMISSION CONTROL WARRANTY PARTS  
LIST: Carburetor, Ignition System: Spark Plug  
(covered up to maintenance schedule), Ignition  
Module, Muffler including catalyst. MAINTE-  
NANCE STATEMENT: The owner is responsi-  
ble for the performance of all required mainte-  
nance as defined in the instruction manual.  
This engine is certified to be emissions compliant for the following use:  
Moderate (50 hours)  
Intermediate (125 hours)  
Extended (300 hours)  
-- 1 0 --  
 

Technicolor Thomson Flat Panel Television EFC030 User Manual
TOA Electronics Microcassette Recorder AM 821 User Manual
Toshiba Network Router GN 1050 User Manual
Triarch Indoor Furnishings MR29230 User Manual
Tricity Bendix Cooktop SIE 532 User Manual
Uniden Answering Machine DECT3181 User Manual
Valcom Speaker V 1070 User Manual
Vermont Casting Electric Heater 1695CE User Manual
Vermont Casting Fan C34G624M User Manual
Vermont Casting Ventilation Hood 3926 User Manual