Tripp Lite TV Mount DWM1737MN User Manual

Owner’s Manual  
Full Motion  
Flat Screen Wall Mount  
MODEL: DWM1737MN  
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR  
PROPERTY DAMAGE MAY OCCUR!  
75x75/100x100  
200x100/200x200  
42”  
52.1kg  
(115lbs)  
MAX  
MAX  
Русскоязычная версия настоящего руководства представлена на веб-сайте компании  
Copyright © 2013 Tripp Lite. All rights reserved.  
 
13-09-231-9332A1-EN.indd  
1
10/31/2013 11:50:15 AM  
Component Checklist  
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to  
4mm Allen Key (x1)  
DWM1737MN (x1)  
Package M  
M4X14 (x4)  
M5X14 (x4)  
M6X14 (x4)  
M8X20 (x4)  
D5 Washer (x4)  
D8 Washer (x4)  
Small Spacer (x8)  
Package W  
Anchor Bolt (x3)  
Concrete Anchor (x3)  
D6 Washer (x3)  
3
 
13-09-231-9332A1-EN.indd  
3
10/31/2013 11:50:16 AM  
1. Separate the VESA Plate from the Wall Mount  
2a. Mount on Wood Stud Wall  
Find and mark  
1
2
3
the exact  
location of  
mounting holes  
Drill pilot holes  
D6 Washer  
Anchor Bolt  
Screw the wall  
plate onto the  
wall  
WARNING  
• Make sure that mounting screws are anchored into the center of the studs.  
Use of a stud finder is highly recommended.  
• Installers are responsible to provide hardware for other types of mounting situations.  
• Installers must verify that the supporting surface will safely support the combined  
load of the equipment and all attached hardware and components.  
4
 
13-09-231-9332A1-EN.indd  
4
10/31/2013 11:50:16 AM  
2b. Mount on Solid Brick and Concrete Block  
Find and mark the  
exact location of  
mounting holes  
1
2
Drill pilot holes  
D6 Washer  
Concrete Anchor  
Anchor Bolt  
Screw the wall  
plate onto the  
wall  
WARNING  
• When installing wall mounts on cinder block, verify the actual concrete thickness  
is at least 1-3/8” (35mm) for using the concrete anchors. Do not drill into mortar  
joints! Be sure to mount in a solid part of the block, generally 1” (25mm) minimum  
from the side of the block. It is suggested an electric drill on a slow setting be used  
to drill the hole instead of a hammer drill to avoid breaking out the back of the hole  
when entering a void or cavity.  
• Installers must verify that the supporting surface will safely support the combined  
load of the equipment and all attached hardware and components.  
5
 
13-09-231-9332A1-EN.indd  
5
10/31/2013 11:50:18 AM  
3. Install VESA Plate  
TV  
TV  
TV  
TV  
M4X14 / M5X14  
M6X14 / M8X20  
D5 Washer  
D8 Washer  
Top of TV  
or  
M8X20  
D5 Washer  
Small Spacer  
Top of TV  
M8X20  
D5 Washer  
Small Spacer  
Small Spacer  
Note: Choose appropriate screws, washers and spacers (if necessary) according to the type of screen.  
Screw VESA plate onto the TV.  
Tighten all screws but do not over tighten.  
6
 
13-09-231-9332A1-EN.indd  
6
10/31/2013 11:50:18 AM  
4. Hang TV onto the Wall Plate  
• Level the TV.  
• Reattach the lower flat nut (removed in step 1) and tighten both nuts.  
7
 
13-09-231-9332A1-EN.indd  
7
10/31/2013 11:50:20 AM  
5. Adjustment  
4mm Allen Key  
Because the weight of displays vary, it is necessary to  
slightly tighten or loosen the adjustment screw with the  
supplied Allen Key.  
80°  
+15°  
-15°  
-4°  
+4°  
Adjust to the desired location or tilt.  
Maintenance  
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).  
13-09-231 93-32A1_RevA  
8
 
13-09-231-9332A1-EN.indd  
8
10/31/2013 11:50:22 AM  

Tiffen Camera Accessories Pro Mist and Warm Pro Mist Filter User Manual
TOA Electronics Microphone WM 5270UHF User Manual
Toastmaster Blender RRFP1A T TM User Manual
Toshiba Universal Remote RBC AS21UL User Manual
Triarch Indoor Furnishings 75010 User Manual
Troy Bilt Edger 554 User Manual
True Fitness Treadmill Excel Series User Manual
U Line Ice Maker CO2075DWR User Manual
Uniden Cordless Telephone D13842BK User Manual
VDO Dayton Car Stereo System CD1537x User Manual